Chapter 14
Fluid Mechanics
States of Matter
Solid
Has a definite volume and shape
Liquid
Has a definite volume but not a definite shape
Gas
unconfined
Has neither a definite volume nor shape
States of Matter, cont
All
of the previous definitions are somewhat
artificial
More generally, the time it takes a particular
substance to change its shape in response to
an external force determines whether the
substance is treated as a solid, liquid or gas
Fluids
A
fluid is a collection of molecules that are
randomly arranged and held together by
weak cohesive forces and by forces exerted
by the walls of a container
Both liquids and gases are fluids
Forces in Fluids
Fluids do not sustain shearing stresses or tensile
stresses
The only stress that can be exerted on an object
submerged in a static fluid is one that tends to
compress the object from all sides
The force exerted by a static fluid on an object is
always perpendicular to the surfaces of the object
Pressure
The pressure P of the
fluid at the level to
which the device has
been submerged is the
ratio of the force to the
area
F
P
A
Pressure, cont
Pressure
If
is a scalar quantity
Because it is proportional to the magnitude of the
force
the pressure varies over an area, evaluate
dF on a surface of area dA as dF = P dA
Unit of pressure is pascal (Pa)
1Pa 1 N/m2
Measuring Pressure
The spring is calibrated
by a known force
The force due to the
fluid presses on the top
of the piston and
compresses the spring
The force the fluid
exerts on the piston is
then measured
Density Notes
Density
is defined as the mass per unit
volume of the substance
The values of density for a substance vary
slightly with temperature since volume is
temperature dependent
The various densities indicate the average
molecular spacing in a gas is much greater
than that in a solid or liquid
Density Table
Pressure and Depth
Examine the darker
region, a sample of
liquid within a cylinder
It has a crosssectional area A
Extends from depth d
to d + h below the
surface
Three external forces
act on the region
Pressure and Depth, cont
The
liquid has a density of
Assume the density is the same throughout the
fluid
This means it is an incompressible liquid
The
three forces are:
Downward force on the top, P0A
Upward on the bottom, PA
Gravity acting downward, Mg
The mass can be found from the density:
M V Ah
Pressure and Depth, final
Since the net force must be zero:
PA
j
P
A
j
Mg
j
This chooses upward as positive
Solving for the pressure gives
P = P0 + gh
The pressure P at a depth h below a point in the
liquid at which the pressure is P0 is greater by an
amount gh
Atmospheric Pressure
If
the liquid is open to the atmosphere, and P0
is the pressure at the surface of the liquid,
then P0 is atmospheric pressure
P0
= 1.00 atm = 1.013 x 105 Pa
Pascals Law
The
pressure in a fluid depends on depth and
on the value of P0
An
increase in pressure at the surface must
be transmitted to every other point in the fluid
This is the basis of Pascals law
Pascals Law, cont
Named
for French scientist Blaise Pascal
A change in the pressure applied to a fluid
is transmitted undiminished to every point
of the fluid and to the walls of the
container
P1 P2
F1 F2
A1 A2
Pascals Law, Example
Diagram of a hydraulic
press (right)
A large output force can be
applied by means of a
small input force
The volume of liquid
pushed down on the left
must equal the volume
pushed up on the right
Pascals Law, Other
Applications
Hydraulic
Car
brakes
lifts
Hydraulic jacks
Forklifts
Pressure Measurements:
Barometer
Invented by Torricelli
A long closed tube is filled
with mercury and inverted in
a dish of mercury
The closed end is nearly a
vacuum
Measures atmospheric
pressure as Po = Hggh
One 1 atm = 0.760 m (of Hg)
Pressure Measurements:
Manometer
A device for measuring the
pressure of a gas contained
in a vessel
One end of the U-shaped
tube is open to the
atmosphere
The other end is connected
to the pressure to be
measured
Pressure at B is P = P0+gh
Absolute vs. Gauge Pressure
P
= P0 + gh
is the absolute pressure
The gauge pressure is P P0
This is also gh
This is what you measure in your tires
Buoyant Force
The buoyant force is
the upward force
exerted by a fluid on
any immersed object
The parcel is in
equilibrium
There must be an
upward force to
balance the downward
gravitational force
Archimedess Principle
The magnitude of the buoyant force always equals
the weight of the fluid displaced by the object
This is called Archimedess Principle
Archimedess Principle does not refer to the makeup
of the object experiencing the buoyant force
The objects composition is not a factor since the
buoyant force is exerted by the fluid
Archimedess Principle, cont
The pressure at the top
of the cube causes a
downward force of Ptop
A
The pressure at the
bottom of the cube
causes an upward
force of Pbot A
B = (Pbot Ptop) A
= fluid g V = Mg
Archimedes's Principle:
Totally Submerged Object
An
object is totally submerged in a fluid of
density fluid
The upward buoyant force is
B = fluid g V = fluid g Vobject
The downward gravitational force is
Fg = Mg = = obj g Vobj
The net force is B - Fg = (fluid obj) g Vobj
Archimedess Principle: Totally
Submerged Object, cont
If the density of the object is less
than the density of the fluid, the
unsupported object accelerates
upward
If the density of the object is
more than the density of the
fluid, the unsupported object
sinks
The direction of the motion of
an object in a fluid is
determined only by the
densities of the fluid and the
object
Archimedess Principle:
Floating Object
The
object is in static equilibrium
The upward buoyant force is balanced by the
downward force of gravity
Volume of the fluid displaced corresponds to
the volume of the object beneath the fluid
level
obj
Vfluid
Vobj
fluid
Archimedess Principle:
Floating Object, cont
The
fraction of the
volume of a floating
object that is below
the fluid surface is
equal to the ratio of
the density of the
object to that of the
fluid
Use the active figure
to vary the densities
Archimedess Principle, Crown
Example
Archimedes
was (supposedly) asked, Is the
crown made of pure gold?
Crowns weight in air = 7.84 N
Weight in water (submerged) = 6.84 N
Buoyant force will equal the apparent weight
loss
Difference in scale readings will be the buoyant
force
Archimedess Principle, Crown
Example, cont.
F = B + T2 Fg = 0
B = Fg T2
(Weight in air weight in
water)
Archimedess principle
says B = gV
Find V
Then to find the material
of the crown, crown =
mcrown in air / V
Archimedess Principle,
Iceberg Example
What
fraction of the iceberg is below water?
The iceberg is only partially submerged and
so Vseawater / Vice = ice / seawater applies
The fraction below the water will be the ratio
of the volumes (Vseawater / Vice)
Archimedess Principle,
Iceberg Example, cont
Vice is the total volume
of the iceberg
Vwater is the volume of
the water displaced
This will be equal to the
volume of the iceberg
submerged
About 89% of the ice is
below the waters
surface
Types of Fluid Flow Laminar
Laminar
flow
Steady flow
Each particle of the fluid follows a smooth path
The paths of the different particles never cross
each other
Every given fluid particle arriving at a given point
has the same velocity
The path taken by the particles is called a
streamline
Types of Fluid Flow
Turbulent
An
irregular flow characterized by small
whirlpool-like regions
Turbulent flow occurs when the particles go
above some critical speed
Viscosity
Characterizes
the degree of internal friction in
the fluid
This internal friction, viscous force, is
associated with the resistance that two
adjacent layers of fluid have to moving
relative to each other
It causes part of the kinetic energy of a fluid
to be converted to internal energy
Streamlines
The path the particle
takes in steady flow is
a streamline
The velocity of the
particle is tangent to
the streamline
A set of streamlines is
called a tube of flow
Equation of Continuity
Consider a fluid moving
through a pipe of
nonuniform size (diameter)
The particles move along
streamlines in steady flow
The mass that crosses A1 in
some time interval is the
same as the mass that
crosses A2 in that same
time interval
Equation of Continuity, cont
m1 = m2 or A1v1 = A2v2
Since the fluid is incompressible, is a constant
A1v1 = A2v2
This is called the equation of continuity for fluids
The product of the area and the fluid speed at all points
along a pipe is constant for an incompressible fluid
Equation of Continuity,
Implications
The speed is high where the tube is constricted
(small A)
The speed is low where the tube is wide (large A)
The product, Av, is called the volume flux or the flow
rate
Av = constant is equivalent to saying the volume
that enters one end of the tube in a given time
interval equals the volume leaving the other end in
the same time
If no leaks are present
Bernoullis Equation
As
a fluid moves through a region where its
speed and/or elevation above the Earths
surface changes, the pressure in the fluid
varies with these changes
The relationship between fluid speed,
pressure and elevation was first derived by
Daniel Bernoulli
Bernoullis Equation, 2
Consider the two shaded
segments
The volumes of both
segments are equal
The net work done on the
segment is W =(P1 P2) V
Part of the work goes into
changing the kinetic energy
and some to changing the
gravitational potential
energy
Bernoullis Equation, 3
The
change in kinetic energy:
K = mv22 - mv12
There is no change in the kinetic energy of the
unshaded portion since we are assuming
streamline flow
The masses are the same since the volumes are
the same
Bernoullis Equation, 4
The
change in gravitational potential energy:
U = mgy2 mgy1
The
work also equals the change in energy
Combining:
(P1 P2)V = mv22 - mv12 + mgy2 mgy1
Bernoullis Equation, 5
Rearranging and expressing in terms of density:
P1 + v12 + mgy1 = P2 + v22 + mgy2
This is Bernoullis Equation and is often expressed
as
P + v2 + gy = constant
When the fluid is at rest, this becomes P1 P2 = gh
which is consistent with the pressure variation with
depth we found earlier
Bernoullis Equation, Final
The
general behavior of pressure with speed
is true even for gases
As the speed increases, the pressure decreases
Applications of Fluid
Dynamics
Streamline flow around a
moving airplane wing
Lift is the upward force on
the wing from the air
Drag is the resistance
The lift depends on the
speed of the airplane, the
area of the wing, its
curvature, and the angle
between the wing and the
horizontal
Lift General
In
general, an object moving through a fluid
experiences lift as a result of any effect that
causes the fluid to change its direction as it
flows past the object
Some factors that influence lift are:
The shape of the object
The objects orientation with respect to the fluid
flow
Any spinning of the object
The texture of the objects surface
Golf Ball
The ball is given a rapid
backspin
The dimples increase
friction
Increases lift
It travels farther than if
it was not spinning
Atomizer
A stream of air passes over
one end of an open tube
The other end is immersed
in a liquid
The moving air reduces the
pressure above the tube
The fluid rises into the air
stream
The liquid is dispersed into
a fine spray of droplets