Scribd
Upload
883 views21 pages

Eim NC II Pipe Bending

The document describes the parts and operation of a hydraulic pipe bender. It has a frame that holds rollers to position the pipe for bending. A bottle jack uses hydraulic oil to lift a die and bend the pipe when pumped. The operation involves placing the pipe between adjusted rollers, pumping the bottle jack with a handle to bend the pipe to the desired angle, then releasing the screw to remove the bent pipe. The hydraulic pipe bender is useful for consistently bending pipes to various angles.

Uploaded by

Wensore Cambia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
883 views21 pages

Eim NC II Pipe Bending

The document describes the parts and operation of a hydraulic pipe bender. It has a frame that holds rollers to position the pipe for bending. A bottle jack uses hydraulic oil to lift a die and bend the pipe when pumped. The operation involves placing the pipe between adjusted rollers, pumping the bottle jack with a handle to bend the pipe to the desired angle, then releasing the screw to remove the bent pipe. The hydraulic pipe bender is useful for consistently bending pipes to various angles.

Uploaded by

Wensore Cambia
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 21

ELECTRICAL INSTALLATION

AND MAINTENANCE NC II

ELECTRICAL POWER
AND HYDRAULIC
TOOLS
HYDRAULIC

PIPE BENDER

HYDRAULIC PIPE BENDER


Uses hydraulic oil
Heavy duty
performance

PARTS AND FUNCTIONS


ROLLERS
Hold back the
pipe to be
bended

PARTS AND FUNCTIONS


BOTTLE JACK

Container of
the hydraulic oil

PARTS AND FUNCTIONS


FRAME

Holds the rollers

PARTS AND FUNCTIONS


ROLLER BARS
The pins that
are inserted
inside the roller
and serve as the
connector of the
roller to the
frame.

PARTS AND FUNCTIONS


ROLLER BAR
HOLES
Holes in the
frame for roller
adjustments

PARTS AND FUNCTIONS

PUMP SLEEVE
Used to pump
air to the bottle
jack

PARTS AND FUNCTIONS


HANDLE

Inserted to
the pump
sleeve for
convenien
t pumping

PARTS AND FUNCTIONS

RELEASE
SCREW
Releases the
pumped air
when
unscrewed

PARTS AND FUNCTIONS

DIES
Sometimes
called shoes
supports the
pipe during
bending

PARTS OF HYDRAULIC PIPE


BENDER

OPERATION OF A HYDRAULIC
PIPE BENDER
1. Jack in its upright position.
Make sure that there is room
on all sides of the Pipe Bender
for the length of pipe you
intend to bend.
Place the unit on a solid, flat,
level surface capable of
supporting the weight of the Pipe
Bender, pipes, and all other tools
and accessories.
The Pipe Bender must always be
clamped or bolted down to the
workbench when used with a
workbench.

OPERATION OF A HYDRAULIC PIPE


BENDER
2. Select the Bending Die that
matches the size of pipe you
wish to bend. Each Die is
stamped with the pipe size.
Place the selected bending
Die onto the Bottle Jack

OPERATION OF A HYDRAULIC PIPE


BENDER
3. Measure the length
of the pipe with a
tape measure where
you need the bend
to be and then slide
the pipe into place
between the rollers
and the saddle.

OPERATION OF A HYDRAULIC PIPE


BENDER
4. The Rollers need to
be adjusted so that the
top of the pipe to be
bent rests against the
bottom of the Rollers.
Pipe can be bent from
a shallow curve up to
a 90 angle, depending
on the position of the
Rollers and the level of
the Bottle Jack Saddle
before operation

OPERATION OF A HYDRAULIC PIPE


BENDER

5. Using the slotted


end of the Handle
tighten (clockwise)
the Release Valve
on the Bottle Jack.

OPERATION OF A HYDRAULIC PIPE


BENDER

6. Insert the Handle into


the Pump Sleeve and
pump it up and down
to raise the Bottle Jack
and bend the pipe.

OPERATION OF A HYDRAULIC PIPE


BENDER
7. When the pipe has been
bent to the desired
angle, remove the
Handle from the Pump
Sleeve and use it to loosen
the Valve Release Screw
up to one full turn. This will
release the pipe from the
Pipe Bender and allow you
to carefully remove it.

OPERATION OF A HYDRAULIC PIPE


BENDER

END OF SHOW
THANK YOU FOR WATCHING..

You might also like