PUNJAB TECHNICALUNIVERSITY
JALANDHAR (PUNJAB)-144020
6 WEEK INDUSTRIAL TRAINING REPORT ON
EAST CENTRAL RAILWAY HAJIPUR HQ
SIGNAL & TELECOMMUNICATION
PRESENTED BY
SANJEET KUMAR
REGISTRATION NO. - 1308143
BRANCH: ELECTRICAL & ELECTRONICS ENGINEERING
Optical Fiber Communications
Fiber-optic communication is a method of transmitting information from one place to another by sending
pulses of light through an optical fiber. The optical fiber acts as a low loss, wide bandwidth
transmission channel. A light source is required to emit light signals, which are modulated by the signal
data. To enhance the performance of the system, a spectrally pure light source is required
System of Working of OFC System
Quad Cable
Conductor: Each conductor consists of round wire of annealed high conductivity copper.
Insulation: Each conductor is insulated with solid medium/ high density polyethylene insulation.
Quadding: Four insulated conductors stranded to form a star quad, two conductors diagonally opposite
forming one pair and the remaining two diagonally opposite conductors forming the second pairs of the
quad.
Telephone Exchange
The IR (Indian Railway) exchange network is a hierarchical architecture with 3 levels.
Highest level - Zonal Head Quarters (ZHQ) and Railway Board (RB)
Medium level - Divisional HQ (DHQ)
Lowest level - Important activity centers
All telephones shall be push button type. The signaling may be decadic or DTMF
Type. The telephones shall be of the following type:
- Ordinary
- Secretary and Executive type
- Digital
- Magneto
- 4 wire
Various components of the exchange system
a) Exchange hardware
b) Exchange software
c) Man Machine Interaction Terminal PC with Printer
d) Test and measuring instruments
e) Power supply Arrangement consisting of Batteries, Charger, Changeover panel and stand-by system.
f) Intermediate Distribution Frame
g) Main Distribution Frame
h) Protection arrangement
i) Cable (underground and switch board)
j) Subscriber telephone set
k) Maintenance tool
l) Lightning protection and earthling arrangement
STM-1
STM is used by telecommunication backbone networks to transfer packetized voice and data across long
distances. It is a circuit switched networking mechanism, where a connection is established between two
end points before data transfer commences, and torn down when the two end points are done
STM-1 63E1(1E1=2 mbps)
1E1=30 Channel
64 mbps=T ckt
Counting left to right
Mobile Communication
Mobile Train Radio communication is a digital wireless network based on GSM-R (Global System for
Mobile Communication-Railway) designed on EIRENE (European Integrated Railway Radio Enhanced
Network) Functional requirement specification (FRS) and System Requirement specification (SRS)
Basic features of GSM-R
Point to Point call
Voice Broad cast call
Allows user to make a distinct call.
Allows groups of user to receive common
information.
Voice Group call
Allows groups of user to make calls within
/among the groups.
Emergency call
Allows user to call controller by short code or
button during emergency.
Functional addressing
Allows a user or an application to be reached by means of a
number, which identifies the relevant function and not the
physical terminal.
Location dependent addressing
Provides the routing of mobile originated calls to
the correct controller.
geographic area.
Mobile communication process
Video Conferencing
A videoconference is a live connection between people in separate locations for the purpose of
communication, usually involving audio and often text as well as video.
Connect : 19 DRM Office , 5 Division
Required: mic,router/modum,mcu(multi conferencing unit)video phone with codec,large Display
Development of Rail Signalling: India
First Route Relay Interlocking :
Churchgate,WR
centralised Traffic Control
Became a Must for
Gorakhpur- Chappra)
MAUQ by 1950s
Double Wire Signalling
Interlocking: GhaziabadPeshawar 23 Stations
Axle Counter
First Train: Bombay VT Thane
1853
1894
1920
1958
1966
1972
Control system
The Control Organization of IR has primary responsibility for scheduling and running all trains, and
maintaining information on the positions and movements of all rolling stock. (These functions are
collectively known as control - an area of the railway network is said to be 'controlled' when a control
office is in charge of it).A control chart is drawn up by the section controller or his staff for each day.
Fig: Control Panel Room
Basic Signaling
The absolute block system is the most widespread method of train working on IR. The block sections may be
handled manually or automatically, or by some combination of those. Some sections still use different forms
of physical token systems such as the Neale's Ball Token instruments.
Fig: point machine
Interlocking
In railway signalling, an interlocking is an arrangement of signal apparatus that prevents conflicting movements
through an arrangement of tracks such as junctions or crossings. The signalling appliances and tracks are sometimes
collectively referred to as an interlocking plant. An interlocking is designed so that it is impossible to give clear signals
to trains unless the route to be used is proved to be safe.
PI and RRI
Panel Interlocking (PI) is the system used in most medium-sized stations on IR. In this, the points and
signals are worked by individual switches that control them.
Route Relay Interlocking (RRI) is the system used in large and busy stations that have to handle high
volumes of train movements. In this, an entire route through the station can be selected and all the
associated points and signals along the route can be set at once by a switch for receiving, holding,
blocking, or dispatching trains.
Electrical Interlocking(EI) In the more advanced electrical or electronic interlocking schemes, the points
and signals are worked from one integrated mechanism in a signal cabin which features a display of the
entire
Electrical equipment of some kinds may be used even in the mechanical interlocking systems described
above (e.g., electrical relays that operate slotting
Relays
Relays of various sorts are used to turn on or turn off circuits that control signals, points, slots, level
crossing gates, etc. Track relays are used for track circuits. Signal relays control signals.
Most railroad crossing train detection systems can detect trains within at least several hundred feet from
the crossing on either side of the road. Although some of the earliest crossings provided a warning
whenever a train was within detection range, even if the rear of that train had already cleared the crossing,
Track Circuit
Questions??
??
Presented By
Sanjeet Kumar
[email protected]
+91-8968143473
