Scribd
Upload
263 views32 pages

Unit 2.1 Presentation Rock Slope Analysis

The document discusses rock slope failures and their causes. It describes four types of failures - planar, wedge, toppling and circular - which are dependent on the orientation of discontinuities like bedding, foliation and faults. It explains how to analyze slope stability using a stereonet to plot discontinuity data and identify potential failure surfaces based on their orientation relative to the slope. Factors like discontinuity dip and plunge angles are compared to slope angles to determine if kinematic failure criteria are met. The document also provides equations for calculating the factor of safety against slope failure.

Uploaded by

efcarrion
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
263 views32 pages

Unit 2.1 Presentation Rock Slope Analysis

The document discusses rock slope failures and their causes. It describes four types of failures - planar, wedge, toppling and circular - which are dependent on the orientation of discontinuities like bedding, foliation and faults. It explains how to analyze slope stability using a stereonet to plot discontinuity data and identify potential failure surfaces based on their orientation relative to the slope. Factors like discontinuity dip and plunge angles are compared to slope angles to determine if kinematic failure criteria are met. The document also provides equations for calculating the factor of safety against slope failure.

Uploaded by

efcarrion
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 32

Rock Slope Stability

Yonathan Admassu, PhD


James Madison University
Rock Slope Failure

Location: British Columbia, Canada


https://en.wikipedia.org/wiki/Rockfall#/media/File:Rockfall.jpg
Rock Slope Failure

Location: Lauria, Italy Landslide type: Wedge


failure
https://en.wikipedia.org/wiki/Landslide_classification#/media/File:Wedge_slide.JPG
Rock Slope Failure

Location: Canada Landslide type: Rock Slide


https://en.wikipedia.org/wiki/Landslide_classification#/media/File:Mica_Dam_spillway.jpg
Rock Slope Failure

Location: Afton, Virginia along I-64


Rock Slope Failure
Rock Slope Failure
What is the common cause of slope failures shown?

 Failure is along discontinuities


 Orientation of discontinuities controls failure
Types of Discontinuities

 Bedding
 Foliation
 Shear zones
 Fault planes
Kinematic Analysis

 Potential for global failure or releasing rockfalls


 Dependent of discontinuity orientations
 Bedding
 Foliation
 Shear zones
 Fault planes
Kinematic Analysis
Planar Wedge

Planar failure where the Two discontinuities


discontinuity intersects the intersect and also
slope face intersect the slope face

Topple Circular

Circular failure in soil,


Steeply dipping
waste or heavily fractured
discontinuities cause slabs
rock with no definable
and columns to separate
structural pattern
from face
Plane Failure
Plane Failure
Plane Failure Criteria

 Discontinuity should be
parallel to slope face
 Discontinuity should dip at a
gentler angle than slope
face
 Discontinuity dip should be
greater than friction angle
Wedge Failure
Wedge Failure
Wedge Failure Criteria

 Line of intersection should


intersect the slope face
 Line of intersection should
plunge at a gentler angle
than slope face
 Line of intersection should
be greater than friction
angle
Toppling Failure Criteria

The kinematic requirement for toppling failures according to Goodman


(1989) is “If layers have an angle of friction Φj, slip will occur only if the
direction of the applied compression makes an angle greater than the friction
angle with the normal to the layers. Thus, toppling failure with a slope
inclined α degrees with the horizontal and discontinuities dipping at σ can
occur if (90 - σ) + Φj < α”.
Stereonet-Based Kinematic
Analysis
Stereonet-Based Kinematic Analysis
Discontinuity Orientation Measurements

Strike and dip of


the beds.
1-Strike
2-Dip direction
3-Apparent dip
4-Angle of dip
Stereonet-Based Kinematic Analysis
Discontinuity Orientation Measurements

Great Circles
Stereonet-Based Kinematic Analysis
Plotting Discontinuity Orientation

045
045

Dip Vector

Pole
Stereonet-Based Kinematic Analysis
Plotting Discontinuity Orientation

Great Circles Dip Vectors

Poles
Stereonet-Based Kinematic Analysis
Plotting Discontinuity Orientation

Contoured Poles
Poles
Stereonet-Based Kinematic Analysis
Identifying representative great circles using Dips software
Stereonet-Based Kinematic Analysis
Plane failure criteria

Dip Vector Pole


Stereonet-Based Kinematic Analysis
Wedge failure criteria
Stereonet-Based Kinematic Analysis
Wedge failure criteria
Stereonet-Based Kinematic Analysis
Wedge failure criteria- based on lines of intersections
Stereonet-Based Kinematic Analysis
Toppling failure criteria
Factor of safety Calculation

 If kinematic analysis shows the potential for failure


 Factor of safety against failure should be
calculated
Factor of safety Calculation

Find resisting force (Fr): Uplift


Fr = ca + Fn tan  = ca + (W-U cos ) tan 
a=l*1

Find driving force (Fd):

W sin 

Uplift (free draining): U = ¼ aw Hw

Find Safety factor (FS): Uplift (Ice dammed): U = ½ a w Hw

FS = Resisting force/driving force

FS = Fr / Fd = ca+(W cos  - U) tan 

W sin 

You might also like