Scribd
Upload
110 views

Power Quality Improvement and Reactive Power Compensation Using

This document discusses power quality improvement and reactive power compensation using a D-STATCOM. It introduces reactive power as a major concern that affects power quality and defines reactive power compensation as improving the power factor. A D-STATCOM is described as one of the FACTS devices that can be used for reactive power compensation to dynamically control voltage. The document proposes using MATLAB/Simulink software to model and test a D-STATCOM's ability to enhance reactive power compensation for different loads, improving the power system's performance.

Uploaded by

Ramu Lalam
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
110 views

Power Quality Improvement and Reactive Power Compensation Using

This document discusses power quality improvement and reactive power compensation using a D-STATCOM. It introduces reactive power as a major concern that affects power quality and defines reactive power compensation as improving the power factor. A D-STATCOM is described as one of the FACTS devices that can be used for reactive power compensation to dynamically control voltage. The document proposes using MATLAB/Simulink software to model and test a D-STATCOM's ability to enhance reactive power compensation for different loads, improving the power system's performance.

Uploaded by

Ramu Lalam
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 12

POWER QUALITY IMPROVEMENT AND

REACTIVE POWER COMPENSATION


USING D-STATCOM.
PRESENTING BY:
L . SRI RAMA RAO (15K11A0205)
M.Y.PAVANI ( 15K11A0210) UNDER GUIDANCE :
B.SAI PHANINDRA (16K15A0201) K. VENKATESH
G.SWATHI (16K15A0208) ( ASSISTANT
PROFESSOR)
B . SANTOSH KUMAR (15K14A0223)
INTRODUCTION:
 The term power quality is used in synonymous with supply reliability to indicate the
existence of an adequate and secure power supply. Power quality is generally used
to express the quality of the voltage. Power Generation, Transmission and Distribution
is a difficult process, requiring the working of many components of the power system
to maximize the quality of the output. The quality may be reduced by many factors
such as Harmonics, reactive power, voltage sag, swell, and transients. Among all, the
reactive power is the main component to decrease the quality of the waveform. So
we need to compensate the reactive power.
 Reactive power is required to meet the inductive and capacitive loads. Most of the
electrical loads are inductive; hence we need to compensate reactive power. The
Reactive power may be compensated in many ways including FACTS controller,
fixed capacitors and synchronous condensers etc. Nowadays, FACTS controllers are
used for compensating the reactive power. Here distributed static synchronous
compensator (DSTATCOM) is used to compensate the reactive power. DSTATCOM
has many advantages than other FACTS controllers. The advantages of DSTATCOM
are compensating reactive power, and used for reducing the voltage drops improve
the transfer capability of the power in the transmission and distribution lines .The
advantages of reactive power compensation are improved power factor, voltage
balancing, and improve system stability.
ABSTRACT
 In power system reactive power is one of the major concerns which affect the
quality of power. . Management of reactive power is defined as the
improvement of the power factor value so that we can cease the generation of
reactive power. The concept of reactive power compensation is related to the
issue faced in power quality but in general, the reactive power compensation
can be done by considering two parameters i.e., load compensation and
voltage support. In load compensation the aim is to increase the power factor
of the system thus the real power in the system can be increased .In voltage
support, the aim is to reduce the harmonic at the output due to fluctuating
supply. The compensation of reactive power is essential to improve power
quality using FACTS device such as DSTATCOM. A DSTATCOM is one of the
fundamental facts devices, which is used for dynamic voltage control. Using this
control strategy the reference voltage and current signals are generated. These
reference signals are used to generate pulses for the D-STATCOM.The proposed
model and control technique is to be implemented by using MATLAB/Simulink
software which offers a smart tool for enhancement of reactive power for
different loads using DSTATCOM, which increases the performance of system.
Electrical grid:
An electrical grid is a network of
synchronized power providers and consumers that are
connected by transmission and distribution lines and operated
by one or more control centres .
FACTS DEVICES:
Flexible Alternating Current Transmission
System (FACTS) is a static equipment used for the AC Transmission of
electrical energy. It is meant to enhance controllability and increase
power transfer capability . It is generally a power electronic based
device . Those are like SVC , TCSC , TCVR ,TCPCT , UPFC and
STATCOM.
POWERQUALITY:
electric power quality or simple power quality involves voltage,
frequency and harmonics. Good power quality can be defined as a study state
supply voltage that stays within the prescribed range, steady AC frequency close to
the rated value and smooth voltage curve waveform .“ In general , it is use full to
consider power quality as a compatibility between what comes out of an electric
outlet and the load that is plugged in .” zero distortion and disturbances and free
supply.
Power quality problems:
 Voltage sag (or dip)
 Harmonic distortions
 Voltage fluctuations
 Voltage unbalance
 Voltage spikes
HARMONICS:
IN A ELECTRIC POWER SYSTEM , A HARMONIC IS A VOLTGE OR
CURRENT At a integral multiple of fundamental frequency of the system, produced by the action of
non linear loads like such as rectifiers, inverters, discharging lights, or saturated magnetic drives.
Harmonics in power system results in increased heating in the equipment and conductors, misfiring in
variable speed drives and torque pulsations in motors .
NON LINEAR LOADS :
A load is considered non – linear if its impedance
changes with the applied voltage . the changing impedance means that
the current drawn by the non-linear load will not be sinusoidal even
when it is connected to a sinusoidal voltage.
REACTIVE POWER:
Real power is considered to be the
work producing power measured in Watts or kilo Watts. Real power produces the mechanical
output of a motor. Reactive power is not used but is needed to operate the equipment and is
measured in volt- amperes-reactive VAR or KVAR. From the power triangle shown below, the
compensation of reactive power decreases the apparent power. Thus, the total consumption of
power is also reduced. It reduces the payment of the electricity bill is measured.

NEEDFORREACTIVEPOWERCOMPENSATION:
The voltage regulation is used to increase the system stability, better utilization of machines connected to
the system and to reduce the losses associated with the system.. The impedance of transmission line and the
need for lagging VAR by most electrical machines in a generating system results in the consumption of
reactive power (Q), thus affecting the stability limits of the system and transmission lines. Unnecessary
voltage drops lead to increased losses which need to be supplied by the source and are leading to outages
in the line due to stress on the system to carry this imaginary power.
POWERFACTOR:
The ratio of the actual
electrical power dissipated by an AC circuit divided by product of the
RMS values of currents and voltages is known as “Power factor”.

Increasing the Power Factor:


As the power factor
(cos θ) increases, the ratio of true power to apparent power (which =
cos θ), increases and approaches unity (1), while the phase angle θ
decreases and the Q decreases. [As cos θ → 1, its maximum possible
value, θ → 0 and so reactive power= 0, as the load becomes less
reactive and more purely resistive].

Decreasing the Power Factor:


As the pf decreases, the
ratio of true power to apparent power also decreases, as the angle θ
increases and reactive power increases.
REACTIVE POWER COMPENSATION METHODS

 Shunt compensation
 Series compensation
 Synchronous condensers
 Static VAR compensators
 Static compensators
DSTATCOM:
A DSTATCOM (Distributed static
synchronous compensator),which is schematically depicted in
figure shown below, consists of a two level voltage source
inverter(VSI),a dc energy device, a coupling transformer are
connected in shunt to the distribution network through a
coupling transformer. VSI converts the dc voltage across the
energy device into a set of three phase ac output voltage.
These voltages are in phase and coupled with the system
undergo the reactance of the coupling transformer. Suitable
adjustment of the phase angle and magnitude of the D-
STATCOM output voltages grant effective control of active and
reactive power exchanges between the D-STATCOM and ac
system. The Voltage source inverter connected in shunt with the
ac system provides a multifunctional topology which can be
used for three quite distinct purposes:
1) Improves Voltage regulation and compensation of reactive
power .
2) Power factor correction.
3) Elimination of current harmonics.
FUTURE SCOPE
 Mathematical analysis.
 To learn the MATALAB software.

You might also like