STEAM TURBINE
Presented by:- Guide by:-
M V DIWAKAR ACHARI Mr” Sri.P.NARENDER
M.Tech,PH.D
(Proffesor Dept of Mech in UCE.OU )
What is a Turbine ?
-A Turbine is a device which converts the heat energy of steam into
the kinetic energy & then to rotational energy.
-The Power in a steam turbine is obtained by the rate of change in
momentum of a high velocity jet of steam impinging on a curved
blade which is free to rotate.
-The basic cycle for the steam turbine power plant is the Rankine
cycle. The modern Power plant uses the rankine cycle modified to
include superheating, regenerative feed water heating & reheating.
INTRODUCTION OF STEAM TURBINE
STEAM TURBINE is a prime mover in which pressure energy of steam is converted
into mechanical energy & further electrical energy.
CLASSIFICATION OF STEAM TURBINE
(a) Simple impulse turbine
(b) Reaction turbine
A rotor of a
modern steam
turbine, used in a
power plant
Construction of steam turbines
Principles of operation
•The power in a steam turbine is obtained by the rate of change in
momentum of a high velocity jet of steam impinging on a curved blade
which is free to rotate.
•The steam from the boiler is expanded in a nozzle, resulting in the
emission of a high velocity jet. This jet of steam impinges on the moving
vanes or blades, mounted on a shaft. Here it undergoes a change of
direction of motion which gives rise to a change in momentum and
therefore a force.
•Steam turbines are mostly 'axial flow' types; the steam flows over the
blades in a direction Parallel to the axis of the wheel. 'Radial flow' types
are rarely used.
(a)Simple Impulse turbine
In this type, the drop in pressure takes place in fixed nozzles as well as moving
blades. The pressure drops suffered by steam while passing through the moving
blades causes a further generation of kinetic energy within these blades, giving rise
to reaction and add to the propelling force, which is applied through the rotor to the
turbine shaft. The blade passage cross-sectional area is varied (converging type).
[FIG-The simple Impulse turbine]
(b) Reaction turbine
In the reaction turbine high pressure steam from the boiler, passes
through the nozzle. When the steam comes out through these nozzles
the velocity of steam increases & then strike on fixed blade. In this type
of turbine there is a gradually pressure drop takes place over fixed &
moving blade.
Difference b/w Impulse and Reaction Turbine
The main difference between impulse and
reaction turbine lies in the way in which
steam is expanded while it moves throw
them In the former type steam expands in
the nozzle and its pressure doesn’t change
as it moves over the blades while in the
later types the steam expands
continuously as it passes over the blades
and thus there is a gradual fall in pressure
during expansion
Advantages of Steam turbines:
01) Thermal Efficiency of a Steam Turbine is much higher than that of a
steam engine.
02) The Steam Turbine develops power at a uniform rate and hence does not
required Flywheel.
03) If the Steam Turbine is properly designed and constructed then it is the
most durable Prime Mover.
04) In a steam turbine there is no loss due to initial condensation of steam.
05) In Steam Turbine no friction losses are there.
Disadvantages of steam turbines
1) High efficiency is ordinarily obtained only at high speed.
1) Gas turbine locomotives had similar problems, together with a range of
other difficulties.
3) These devices are heavy and cumbersome.
4) Turbines can rotate in only one direction.
Conclusion
The steam turbine is a prime mover in which the potential energy
of steam is transformed into kinetic energy, and then transferred
into mechanical energy by the turbine shaft. so it is concluded that
the steam turbine is very useful for mechanical work.
DESIGN OF hp TURBINE rotor
DESIGN OF lp TURBINE rotor
REFERENCES;
Thermal engineering R.K. Rajput
Power plant engineering P.K. Nag
Power plant engineering Arora & Domkundawar
Advanced class steam turbine blades
for improved efficieny T.K. Ghouse, P.k. Bansal
www.google.co.in/steam turbines
www.bhel.com
