Distributed Control Systems

PROF.DR. JOYANTA KUMAR ROY

NARULA INSTITUTE OF TECHNOLOGY
DEPT. OF ELECTRONICS AND INSTRUMENTATION ENGINEERING
 DEFINATION

A distributed control system (DCS) refers to a control system

usually of a manufacturing system, process or any kind of
dynamic system, in which the controller elements are not central in
location (like the brain) but are distributed throughout the system
with each component sub-system

DCS (Distributed Control System) is a computerized control

system used to control the production line in the industry
.controlled by one or more controllers
DCS is a very broad term used in a variety of industries, to monitor
.and control distributed equipment
APPLICATION AREA

and electrical generation plants Electrical power grids

Environmental control systems
Traffic signals
Radio signals
Water management systems
Oil refining plants
process plants Metallurgical
Chemical plants
Pharmaceutical manufacturing
Sensor networks
Dry cargo and bulk oil carrier ships
 HISTORY

The DCS was introduced in 1975. Both Honeywell and Japanese

electrical engineering firm Yokogawa introduced their own
independently produced DCSs at roughly the same time, with the
TDC 2000 and CENTUM[3] systems, respectively. US-based
Bristol also introduced their UCS 3000 universal controller in 1975.
In 1978 Metso(known as Valmet in 1978) introduced their own
DCS system called Damatic (latest generation named Metso
DNA[4]). In 1980, Bailey (now part of ABB[5]) introduced the
NETWORK 90 system. Also in 1980, Fischer & Porter Company
(now also part of ABB[6]) introduced DCI-4000 (DCI stands for
.Distributed Control Instrumentation)
Distributed Control Systems

 Collection of hardware and instrumentation

necessary for implementing control systems

 Provide the infrastructure (platform) for

implementing advanced control algorithms
History of Control Hardware

 Pneumatic Implementation:
– Transmission: the signals transmitted
pneumatically are slow responding and
susceptible to interference.

– Calculation: Mechanical computation devices

must be relatively simple and tend to wear out
quickly.
History (cont.)

 Electron analog implementation:

– Transmission: analog signals are susceptible to
noise, and signal quality degrades over long
transmission line.

– Calculation: the type of computations possible

with electronic analog devices is still limited.
History (cont.)

 Digital Implementation:

– Transmission: Digital signals are far less sensitive

to noise.

– Calculation: The computational devices are digital

computers.
Advantages of Digital System

 Digital computers are more flexible because they

are programmable and no limitation to the
complexity of the computations it can carry out.
 Digital systems are more precise.
 Digital system cost less to install and maintain
 Digital data in electronic files can be printed out,
displayed on color terminals, stored in highly
compressed form.
Computer Control Networks

1. PC Control:
Display
 Good for small
processes such as
laboratory prototype
Main
or pilot plants, where Computer

the number of
control loops is Final
control PROCESS
Data
acquisition
relatively small element
Computer Control Networks

2. Programmable Logic Controllers:

 specialized for non-continuous systems such as
batch processes.

 It can be used when interlocks are required; e.g., a

flow control loop cannot be actuated unless a pump
has been turned on.

 During startup or shutdown of continuous processes.

Computer Control Networks
Supervisory (host)
Computer

3. DCS
Operator Main Operator Archival
Control Control Control Data

•Most Panel Computer Panel Storage

comprehensive
Data highway
To other Processes To other Processes

Local data acquisition and Local Local Local

control computers Computer Computer Computer
Local Display Local Display

PROCESS
DCS Elements-1

 Local Control Unit: This unit can handle 8 to 16

individual PID loops.
 Data Acquisition Unit: Digital (discrete) and analog I/O
can be handle.
 Batch Sequencing Unit: This unit controls a timing
counters, arbitrary function generators, and internal
logic.
 Local Display: This device provides analog display
stations, and video display for readout.
 Bulk Memory Unit: This unit is used to store and recall
process data.
DCS Elements-2

 General Purpose Computer : This unit is programmed

by a customer or third party to perform optimization,
advance control, expert system, etc
 Central Operator Display: This unit typically contain
several consoles for operator communication with the
system, and multiple video color graphics display units
 Data Highway : A serial digital data transmission link
connecting all other components in the system. It allow
for redundant data highway to reduce the risk of data loss
 Local area Network (LAN)
Advantages of DCS

 Access a large amount of current information from the data

highway.
 Monitoring trends of past process conditions.
 Readily install new on-line measurements together with local
computers.
 Alternate quickly among standard control strategies and
readjust controller parameters in software.
 A sight full engineer can use the flexibility of the framework to
implement his latest controller design ideas on the host
computer.
Modes of Computer control

1. Manual signals from digital

computer

Local PID
2. Automatic FC controller

• PID with local set point

Supervisory Control mode
3. Supervisory Flow measurement
to computer
• PID with remote set valve setting
from computer

point (supervisory)
Direct digital Control mode
4. Advanced
Additional Advantage

 Digital DCS systems are more flexible.

Control algorithms can be changed and
control configuration can be modified without
having rewiring the system.
Categories of process information

Example Type
Relay, Switch Digital .1
Solenoid valve
Motor drive
Alphanumerical displays Generalized .2
digital
Turbine flow meter Pulse .3
Stepping motor
Thermocouple or strain gauge (mill volt) Analog .4
Process instrumentation (4-20 am)
Other sensors (0-5 Volt)
Interface between digital computer and
analog instruments

 (A/D) Transducers convert analog signals to

digital signals. (Sensor Computer)

 (D/A) Transducers convert digital signals to

analog signals. (Computer Valve)
Data resolution due to digitization

 Accuracy depends on resolution.

 Resolution depends on number of bits:

Resolution = signal range × 1/(2m -1)

m = number of bits used by the digitizer (A/D)

to represent the analog data
Data Resolution

 Signal = 0 - 1 Volt, 3 bit digitizer:

Analog range Analog Digital Binary

covered equivalent Equivalent representation
to 1/14 0 0 0 000
to 3/14 1/14 1/7 1 001
to 5/14 3/14 2/7 2 010
to 7/14 5/14 3/7 3 011
to 9/14 7/14 4/7 4 100
to 11/14 9/14 5/7 5 101
to 13/14 11/14 6/7 6 110
to 14/14 13/14 1 7 111
Data Resolution

6
Digital data

4
3
2

1
0
0 1/7 2/7 3/7 4/7 5/7 6/7 1
Analog data
Utilization of DCS

 DCS vendor job:

– installation
 Control Engineer Job:
– Configuration
 Built-in PID control:
– How to Tune the PID control?
Utilization of DCS

 Implementation of advanced control:

– Developed software for control algorithms, DMC,
Aspen, etc.
– Control-oriented programming language supplied
by the DCS vendors.
– Self-developed programs using high-level
programming languages (Fortran, C++)
Advanced control topology
Two-ways
Data Bus

Process
DCS
PI
system

PI interface

Online: Real-time data

PI interface: C++ or Fortran

Workstation
DCS Vendors

 Honeywell
 Fisher-Rosemont
 Baily
 Foxboro
 Yokogawa
 Siemens
 GE Fanuc Intelligent Platform
 Schneider Electrics
 ABB
Thank You