Scribd
Upload
247 views

Abis Data Configuration

This document provides steps for configuring the data on the BSC and BTS sides for an Abis interface. On the BSC side, it describes planning the IP addresses, configuring the interface links, BTS basic information, cells and carriers. On the BTS side, it outlines configuring the basic information, cells, boards, links, RF modules and starting the BTS. It emphasizes the importance of coordination between transmission and site engineers during the BTS configuration.

Uploaded by

Habib Bale
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
247 views

Abis Data Configuration

This document provides steps for configuring the data on the BSC and BTS sides for an Abis interface. On the BSC side, it describes planning the IP addresses, configuring the interface links, BTS basic information, cells and carriers. On the BTS side, it outlines configuring the basic information, cells, boards, links, RF modules and starting the BTS. It emphasizes the importance of coordination between transmission and site engineers during the BTS configuration.

Uploaded by

Habib Bale
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 17

Abis data configuration

Contents:
• I- BSC side(data configuration)
• I-1 IP address planning
• I-2 steps of data configuration
• I-3 Commissioning
• II- BTS side (data configuration)
• II-1 Steps of the configuration
• II-2 Commissioning
I-BSC side
In this step according to the RNP planning
we choose the subrack where is locate the
BTS. The PEUB and the SPU (XPU)
should be locate on this subrack.
I-1 IP address planning
• PEUB/ BCIM address:
For this bords we use 168 network
segment.the second digit calculated by the
following formula:subrackNo*20+unit of
slot No. Set the third digit to 0 for the
PEUB and to the link group number for the
BCIM. Set the fourth digit to 1 for the
PEUB and 2 for the BCIM.
I-1 IP address planning
• MLPPP Local and Peer ADDR :
Set the ip addresses in the 172 network
segment. the second digit calculated by
the following formula:subrackNo*20+unit
of slot No. Set the third digit to the link
group number. Set the fourth to 1 for the
BSC and 2 for the BTS
I-2 steps of data configuration
• Abis interface link mode:
ADD MLPPPLNK: FN=2, SN=27, MLPPPGRP=1, LNKLST="1", E1T1LST=“0",E1T1MODE=E1,
E1TSBITMAP=TS_1&TS_2&TS_3&TS_4&TS_5&TS_6&TS_7&TS_8&TS_9&TS_10&TS_11&T
S_12&TS_13&TS_14&TS_15&TS_16&TS_17&TS_18&TS_19&TS_20&TS_21&TS_22&TS_23
&TS_24&TS_25&TS_26&TS_27&TS_28&TS_29&TS_30&TS_31,LIPADDR="172.47.0.1",
PIPADDR="172.47.0.2", LQR=NO, PFC=YES, ACFC=YES, HCMP=YES, HCMPTYP=UDP+IP,
MCTYPE=LONG, PPPMUXEN=ON, AUTHMODE=NO, BEARTYP=BOTHSIGTRF;

• BTS basic information:


ADD BSCBTSINF: BTSTP=IBSC, BTSID=1003, BTSNM="BTS1003", FN=2, SN=4, SSN=1,
ABISCAPOPTMSW=OFF, ABISOPTMCRCSW=OFF, ABISREVFRAMEPERIOD=3,
HIGHPW=NOHIGHPW, ABISREDUNDANCESW=OFF, INTRAFADAPFILTER=OFF;
I-2 steps of data configuration

• OML link:
ADD BTSOMLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,
BCIMIP="168.47.0.2", MLPPPGRP=0;

• Signaling link:
ADD BTSSIGLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,
BCIMIP="168.47.0.2", MLPPPGRP=0;

 Traffic link:
ADD BTSTRFLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,
BCIMIP="168.47.0.2", TRFLNKFLG=0, MLPPPGRP=0;
I-2 steps of data configuration
• Cell and Sector:
ADD CELL: BTSID=1003, FN=2, CN=1003, SCTIDLST="0", PNLST="88", SID=8704, NID=1,
PZID=1, LAC="0x102", LCN=1003, LSCTID="0", ASSALW1X=NO, ASSALWDO=NO,
IFBORDCELL=NO, REVRSSICARRASSNSW=OFF, DOAREVRSSICARRASSNSW=OFF,
DOAPRVPRIASSSW=OFF, DOMULTIBANDASSIGNSW=OFF,
AUTODWNFWDEQLCHANTHD=20, AUTODWNCOUNTTHD=600,
UNBLKFWDEQLCHANTHD=40, DOUSERCOUNTTHD=20, DOAUTODWNCOUNTTHD=600,
DOUNBLKUSERCOUNTTHD=40, CTLAC="0xFFF";

NB: We should add cell for 1x and EVDO services. The Cell No
for the EVDO start by 15xx.
You must separate the Sector ID Lists and Pseudo Noise Code Lists
entered by commas.
I-2 steps of data configuration
• carrier of local BSC:
ADD CDMACH: CN=1003, SCTID=0, CRRIDLST="11", BNDCLS=BC800,
ARFCNLST="185", TYP=CDMA2000, IFBCDMACH=NO, CCLMFLG=NO,
ECCLMFLG=NO, IFTCDMACH=NO, AUTODWNCDMACH=NO;

ADD CDMACH: CN=1503, SCTID=0, CRRIDLST="18", BNDCLS=BC800,


ARFCNLST="308", TYP=EVDO, COLORCODE=1, SECTORID24="0x001007",
EVDOPROVER=RELEASEA, AUTODWNCDMACH=NO;

• Add BTS:
ADD BTS: BTSID=1003, OMCIP=’129.11.99.235’, BTSTP=DBS3900_CDMA;
I-3 Commissioning

• Check the basic information:


LST BSCBTSINF
• Check the BTS link:
LST BTSLNK
LST BTS
• Query the Cell and carrierr information:
LST CELL
LST CDMACH
II- BTS side (data configuration)
• To achieve this step the transmission
between BSC and BTS must be up and
the BTS also must be power on. So it very
import to cooperate with the transmission
and site engineer.
II-1 Steps of the configuration

• Basic information cfg


CLR CBTSCFG: BTSID=1003;
SET CBTSINFO: BTSID=1003, BTSTP=CBTS, BTSCLASS=DBS3900_CDMA, CONFIRM=Y;

NB:
• BTS ID must be consistent with the ID which is already
configured in BSC side. (ADD BSCBTSINF).
• Use CLR CBTSCFG to clear the current configuration data of
the BTS .
II-1 Steps of the configuration
• Cell cfg:
ADD CBTSCELL: BTSID=1003,LOCALCELLID=1003,LOCALSECTORID=0;

• Basebande bord cfg:


ADD CBTSCMPT: BTSID=1003,BRDID=0,CONFIRM=Y;
ADD CBTSUTRP:BTSID=1003,BRDID=4,CONFIRM=Y;
NB: CMPT correspond to BCKM on the BTS 3606 and the UTRP to BCIM.

• CE pool CE board cfg:


ADD CBTSCPL:BTSID=1003,CPLID=0,CPLMODE=STATIC,CELLMODE=NORMAL;
ADD CBTSCPL:BTSID=1003,CPLID=1,CPLMODE=STATIC,CELLMODE=NORMAL;
ADD CBTSCPL:BTSID=1003,CPLID=2,CPLMODE=STATIC,CELLMODE=NORMAL;
ADD CBTSCPM: BTSID=1003,BRDID=2,CPLID=0;
ADD CBTSCPM: BTSID=1003,BRDID=3,CPLID=1;
ADD CBTSECM:BTSID=1003,BRDID=0,CPLID=2,WORKINGMODE=CHANNEL3_MODE;
II-1 Steps of the configuration
• MLPP transnission link cfg:
ADD CBTSLNKGRP:BTSID=1003,BRDTP=UTRP,BRDID=4,LNKGRPID=0,LNKGRPTP=MLPPP;

ADD CBTSLNK:BTSID=1003,BRDTP=UTRP,BRDID=4,LNKID=0,LNKGRPID=0;
II-1 Steps of the configuration
• Signaling link and traffic link cfg:
ADD CBTSTERSIGLNK:BTSID=1003,IPVER=IPV4,BSCIP="80.144.16.131",BTSIP="80.126.4.17
",BTSSNM="255.255.0.0",BRDTP=UTRP,BRDID=4,ABISLNKTP=CDMA1XONLY,BEARERTP=IP,P
ERIP="168.47.0.1",PROTOCOLTP=TCP;
ADDCBTSTERSIGLNK:BTSID=1003,IPVER=IPV4,BSCIP="80.144.16.131",BTSIP="80.126.4.17",B
TSSNM="255.255.0.0",BRDTP=UTRP,BRDID=4,ABISLNKTP=CDMADOONLY,BEARERTP=IP,PE
ERIP="168.47.0.1",PROTOCOLTP=TCP;
ADDCBTSIPTERTRFLNK:BTSID=1041,IPLNKID=0,SVCTP=ALL,BRDTP=UTRP,BRDID=4,BUFFM
NUM=3,LNKLAYERTP=PPP,LNKGRPID=0;

NB: for each service we should configure a signaling link. One traffic link is used the both service.
Use LST BTSLNK to query BTSIP address for signaling link and LST SUBSYSTEM to query
BSCIP address.
II-1 Steps of the configuration
• RF module cfg:
ADD CBTSTRM:BTSID=1003,TRMID=0,RCKTP=RRU,TRMDES="RRU0",MASTERBRD=CPM2,F
IBPN=0,FIBTS=0;
ADD CBTSSECTORCARRIER: BTSID=1003, LOCALCELLID=1, LOCALSECTORID=0, CRRID=0,
TRMID=0,CPLID=0,HPBFLG=NO;

NB: we have three RRUs to configure and each one is connect to one optical port of the HCPM.

• Start the BTS:


STR CBTS: BTSID=1003;

• Save the current configuration:


SAV CBTSCFG: BTSID=1003;
II-2 Commissioning
• Check the signaling link status
DSP SIGLNKSTAT
• Check the resources status:
DSP RES
• unblock the resources:
UBL RES
• Query CE information:
LST BSCBTSINF

You might also like