Scribd
Upload
52 views

Data & Signals (Part 1) : Dept. of Computer Engineering Faculty of Engineering

This document provides an overview of key concepts in digital to digital conversion for data communication. It discusses signal element vs data element, signal rate vs data rate, baseline wandering, DC component, synchronization, and various line coding schemes including unipolar, polar, bipolar, multilevel, and multiline transmission. Line coding is used to represent digital data as digital signals for transmission. Concepts like signal to data ratio, bandwidth, and synchronization are also covered. Examples and problems are provided to illustrate key points about different coding schemes.

Uploaded by

আসিফ রেজা
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
52 views

Data & Signals (Part 1) : Dept. of Computer Engineering Faculty of Engineering

This document provides an overview of key concepts in digital to digital conversion for data communication. It discusses signal element vs data element, signal rate vs data rate, baseline wandering, DC component, synchronization, and various line coding schemes including unipolar, polar, bipolar, multilevel, and multiline transmission. Line coding is used to represent digital data as digital signals for transmission. Concepts like signal to data ratio, bandwidth, and synchronization are also covered. Examples and problems are provided to illustrate key points about different coding schemes.

Uploaded by

আসিফ রেজা
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 36

Data & Signals (Part 1)

Course Code: COE 3201 Course Title: Data Communication

Dept. of Computer Engineering


Faculty of Engineering

Lecture No: 5 Week No: 5 Semester:


Lecturer:
Lecture Outline

1. Digital to Digital Conversion


2. Signal Element vs Data Element
3. Signal Rate vs Data Rate
4. Baseline Wandering
5. DC Component
6. Synchronization
7. Line Coding: a) Unipolar
b) Polar
c) Bipolar
d) Multilevel
e) Multitransition
Digital to Digital Conversion

 Digital to digital conversion is the way of representing digital


data by using digital signals. The conversion involves three
techniques: line coding, block coding, and scrambling.

 Line coding is always needed. We will mainly discuss line


coding in this lecture.

 Block coding and scrambling may or may not be needed.


Signal Element vs Data Element

 Signal element
• The shortest unit (timewise) of a digital signal.
 Data element
• The smallest entity that can represent a piece of
information: this is bit.
 In other words
• Data elements are what we need to send.
• Signal elements are what we can send.
Signal Element vs Data Element
Signal Rate vs Data Rate
 Signal rate
• The number of signal elements sent in 1s
• The unit is baud
 Data rate
• The number of data elements (bits) sent in 1s
• The unit is bits per second (bps)
 Relationship between data rate and signal rate
1
S  c N  baud
r
 S: signal rate (baud), c: case factor, N: data rate (bps), r: data elements per
signal elements
Signal Rate vs Data Rate

Problem:
A signal is carrying data in which one data element is encoded
as one signal element (r = 1). If the bit rate is 100 kbps, what is
the average value of the baud rate if c is assumed to vary
between 0 and 1?
Solution:
We assume that the average value of c is 1/2 . The baud rate is
then
Signal Rate vs Data Rate

Problem:
The maximum data rate of a channel is Nmax = 2 × B × log2 L
(defined by the Nyquist formula). Does this agree with the
previous formula for Nmax?

Solution:
A signal with L levels can carry log2L bits per level. If each
level corresponds to one signal element and we assume the
average case (c = 1/2), then we have
Baseline Wandering

 In decoding a digital signal, the receiver calculates a running average


of the received signal power.
 This average is called the baseline.
 The incoming signal power is evaluated against this baseline to
determine the value of the data element.
 A long string of 0s or 1s can cause a drift in the baseline (baseline
wandering) and make it difficult for the receiver to decode correctly.
 A good line coding scheme needs to prevent baseline wandering.
DC Component

 When the voltage level in a digital signal is constant for a


while, the spectrum creates very low frequencies (results of
Fourier analysis).
 These frequencies around zero, call DC (direct-current)
components, present problems for a system that cannot pass
low frequencies or a system that uses electrical coupling (via
a transformer).
 For example, a telephone line cannot pass frequencies below
200 Hz.
Synchronization
 To correctly interpret the signals received from the sender, the
receiver’s bit intervals must correspond exactly to the sender’s bit
intervals. If the receiver clock is faster or slower, the bit intervals are
not matched, and the receiver might misinterpret the signals.
 Self-synchronization
• Digital signal includes timing information in the data being
transmitted.
• This can be achieved if there are transitions in the signal that alert
the receiver to the beginning, middle, or end of the pulse.
Effect of Lack of Synchronization
Effect of Lack of Synchronization

Problem:
In a digital transmission, the receiver clock is 0.1 percent faster than the
sender clock. How many extra bits per second does the receiver receive
if the data rate is 1 kbps? How many if the data rate is 1 Mbps?

Solution:
At 1 kbps, the receiver receives 1001 bps instead of 1000 bps.

At 1 Mbps, the receiver receives 1,001,000 bps instead of 1,000,000


bps.
Line Coding
Line coding schemes
Unipolar
Non-Return to Zero

It is called NRZ because the signal does not return to zero at


the middle of the bit.
Polar
NRZ-L (NRZ-Level), NRZ-I (NRZ-Invert)
Polar: NRZ-L (NRZ-Level), NRZ-I (NRZ-Invert)

 In NRZ-L the level of the voltage determines the value of


the bit.

 In NRZ-I the inversion or the lack of inversion


determines the value of the bit.

 NRZ-L and NRZ-I both have an average signal rate of N/2


Baud.

 NRZ-L and NRZ-I both have a DC component problem.


Polar: NRZ-L (NRZ-Level), NRZ-I (NRZ-Invert)

Problem:
A system is using NRZ-I to transfer 10-Mbps data. What are
the average signal rate and minimum bandwidth?

Solution:
The average signal rate,
S = N/2 = 5000 kbaud
The minimum bandwidth for this average baud rate,
Bmin = S = 5000 kHz.
Polar
RZ: Return-to-Zero Scheme
Polar Biphase
Manchester and Differential Manchester Schemes
Manchester and differential Manchester schemes

 In Manchester and differential Manchester encoding, the


transition at the middle of the bit is used for synchronization.

 The minimum bandwidth of Manchester and differential


Manchester is 2 times that of NRZ.
Bipolar Schemes
AMI and Pseudoternary

 Bipolar encoding (sometimes called multilevel binary)


• Three voltage levels: positive, negative, and zero
 Two variations of bipolar encoding
o AMI (alternate mark inversion)
• 0: neutral zero voltage
• 1: alternating positive and negative voltages
o Pseudoternary
• 1: neutral zero voltage
• 0: alternating positive and negative voltages
 Bipolar schemes have no DC component problem
 In bipolar encoding, we use three levels: positive, zero, and negative.
AMI and Pseudoternary

 AMI (alternate mark inversion)


• The word mark comes from telegraphy and means 1
• AMI means alternate 1 inversion
• The neutral zero voltage represents binary 0
• Binary 1s are represented by alternating positive and
negative voltages
 Pesudoternary
• Same as AMI, but 1 bit is encoded as a zero voltage and
the 0 bit is encoded as alternating positive and
negative voltages.
AMI and Pseudoternary
Multilevel Schemes

 The desire to increase the data speed or decrease the required


bandwidth has resulted in the creation of many schemes.

 The goal is to increase the number of bits per baud by encoding a


pattern of m data elements into a pattern of n signal elements.

 Different types of signal elements can be allowed for different


signal levels.
Multilevel Schemes

 If we have L different levels, then we can produce Ln


combinations of signal patterns.

 The data element and signal element relation is

 mBnL coding, where m is the length of the binary pattern, B


means binary data, n is the length of the signal pattern, and
L is the number of levels in the signaling.

 B (binary, L=2), T (tenary, L=3), and Q (quaternary, L=4).


Multilevel: 2B1Q scheme

 2B1Q (two binary, one quaternary)


• m=2, n=1, and L=4
• The signal rate (baud rate)
1 1 1 N
S  cN   N  
r 2 2 4

 2B1Q is used in DSL (digital subscriber line) technology to


provide a high-speed connection to the Internet by using
subscriber telephone lines.
Multilevel: 2B1Q scheme
Multilevel: 8B6T scheme

 This code is used with 100BASE-4T cable.


 Encode a pattern of 8 bits as a pattern of 6 signal elements,
where the signal has three levels (ternary).
 28=256 different data patterns and 36=729 different signal
patterns. (The mapping is shown in Appendix D.)
 There are 729-256=473 redundant signal elements that
provide synchronization and error detection.
 Part of the redundancy is also used to provide DC (direct-
current) balance.
Multilevel: 8B6T scheme

 + (positive signal), - (negative signal), and 0 (lack of signal)


notation.
 To make whole stream DC-balanced, the sender keeps track
of the weight Invert - + + - 0 - = -1
Multiline Transmission: MLT-3

Three levels (+V, 0, and –V) and three transition rules to move
the levels
• If the next bit is 0, there is no transition
• If the next bit is 1 and the current level is not 0, the
next level is 0.
• If the next bit is 1 and the current level is 0, the next
level is the opposite of the last nonzero level.
Multiline Transmission: MLT-3

Why do we need to use MLT-3?

• The signal rate for MLT-3 is one-fourth the bit rate


(N/4).
• This makes MLT-3 a suitable choice when we need to
send 100 Mbps on a copper wire that cannot support
more than 32 MHz (frequencies above this level create
electromagnetic emission).
Multiline Transmission: MLT-3
Summary
Books

1. Forouzan, B. A. "Data Communication and Networking. Tata McGraw." (2005).


References

1. Prakash C. Gupta, “Data communications”, Prentice Hall India Pvt.


2. William Stallings, "Data and Computer Communications”, Pearson
3. Forouzan, B. A. "Data Communication and Networking. Tata McGraw." (2005).

You might also like