Gear Drive Flo-tap
Installation Instructions
Quick Installation Guides:
00825-0400-4809 rev. EA – 485 Flanged Flo-tap
00825-0500-4809 rev. DB – 485 Threaded Flo-tap
00825-0200-4585 rev. AA – 585 Flanged Flo-tap
Nomenclature
Instrument
Connections
Lift Rings Top Plate
Gear Drive Plate
Gear Box
Rod Protectors
Full Port
Isolation Valve
Weld the Mounting Hardware Onto
the Pipe
Threaded Flo-tap Flanged Flo-tap
Tack Weld the Mounting Hardware
with 4 Equal Length Tacks
Tack weld anywhere on
the mounting hardware
1
Then again directly across
from the first tack weld
Then on the other 2 sides
3 2
Check to See that the Mounting
Hardware is Level and Square
If it’s not, use a
rubber mallet to
lightly adjust the
hardware and
recheck
Verify that the
ODF Dimension
Matches What is
Listed in the QIG
The ODF is the
dimension from outside
pipe diameter to face
of flange
485 585
Verify that the ODF Dimension
Matches What is Listed in the QIG
The ODF is the
dimension from
outside pipe diameter
to face of flange
For Threaded Flo-tap the dimension
from the pipe OD to the top of the
threadolet is called LMH:
485 Sensor Size 1: 1.38-in. (35 mm)
485 Sensor Size 2: 1.56-in. (40 mm)
485 Sensor Size 3: 2.06-in. (52 mm)
Complete a Continuous Weld Around
the Perimeter of the Unit
Attached the Full Port Valve to the
Mounting Hardware
Threaded Flo-tap Flanged Flo-tap
First, thread the guide nipple into the
mounting then thread the valve
ODV
The valve stem should be in-line with the pipe
so it will not interfere with the insertion rods
The valve must be a full port valve to allow the
Annubar to pass through the valve into the pipe
Verify the ODV Dimension
The ODV is the dimension from the outer diameter of the pipe to the top
of the valve
Flo-tap / Flange 485 Sensor Size 585 Sensor Size ODV Dimension
Rating
1 --- 7.51-in. (190.9 mm)
Threaded
2 --- 8.17-in. (207.5 mm)
ANSI 150 # 1 11 10.5-in. (266.7 mm)
ANSI 300 # 1 11 11.75-in. (298.5 mm)
ANSI 600# 1 11 14.06-in. (357.2 mm)
ANSI 150 # 2 22 11.25-in. (285.8 mm)
ANSI 300 # 2 22 13.00-in. (330.2 mm)
ANSI 600# 2 22 16.38-in. (416.0 mm)
ANSI 150 # 3 44 12.75-in. (323.9 mm)
ANSI 300 # 3 44 16.25-in. (412.8 mm)
ANSI 600# 3 44 19.50-in. (495.3 mm)
Drill the Hole by Using a Hot Tap
Drilling Machine
Guide Ring in
Rosemount
Supplied
Mounting
Hardware
Tag with correct drill hole size
attached to the Annubar
After the Hole is Drilled, Retract the Drill
Past the Valve and Close the Valve
Vent drilling machine and remove the per manufacturers
and site procedures
Threaded Flo-tap Flanged Flo-tap
Remember that the hot tap drilling
machine is under pressure and
exposed to the process fluid
Attach the Fully Retracted Flo-tap
Assembly to the Valve
Threaded Flo-tap
Attach the Fully Retracted Flo-tap
Assembly to the Valve
Flanged Flo-tap – Use a hoist strap and
crane if needed
Quickly Open and Close the Valve to
Pressurize the Annubar, Check for Leaks
If Leaks are Present, Tighten the
Packing Gland Nuts
Attach Rod Protectors
Caution During Insertion
During insertion, the top plate can twist due to the
torque of the gear drive. To keep the Annubar
from twisting, hold the top plate in place during
insertion. Gear Drive
Plate
Top Plate Top Plate and Gear Drive
Plate should remain
Shown parallel during insertion
twisted
~90° from
Gear Drive
Plate
If Using a Drill for Insertion, Attach
the Drill to the Insertion Mechanism
Do not exceed
200 RPM on the
Drill
Insert the Annubar
Stop the
drill and
crank by
hand once
the orange
stripes
reach the
Gear Box
Plate
Continue to Insert the Sensor with
the Manual Crank
Place a finger above the packing
gland to feel for full insertion
CAUTION: Be
careful if doing
this with steam or
other harmful
fluids
When movement
stops, the
Annubar is fully
inserted
Turn the handle an additional ½ turn
to ensure it is fully inserted
Insert the Drive Lock Pin to Secure
the Sensor in Place
Tighten the Nuts to the Gear Box
Plate and Loosen ¼ turn
This gives
an
indication
of full
insertion if
the
Annubar is
retracted at
a later
date.
Retighten the Packing Gland Nuts
