Scribd
Upload
87 views

Transformers: Basics and Types: " Transformers Are The Heart of The Alternating Current System."

Transformers are the heart of the alternating current system. They transfer electrical energy from one circuit to another through electromagnetic induction without changing frequency, but allowing adjustment of voltage. This document discusses the construction, working principle, types and applications of transformers.

Uploaded by

Girish Shankar Mishra
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
87 views

Transformers: Basics and Types: " Transformers Are The Heart of The Alternating Current System."

Transformers are the heart of the alternating current system. They transfer electrical energy from one circuit to another through electromagnetic induction without changing frequency, but allowing adjustment of voltage. This document discusses the construction, working principle, types and applications of transformers.

Uploaded by

Girish Shankar Mishra
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 28

“ Transformers are the heart of the

alternating current system.”


.

*Transformers:
Basics and Types
Contents
Transformers:
Constructional details and working
EMF equation
Voltage regulation, losses and efficiency
Open/short- circuit tests and determination of
efficiency.
Three Phase Induction Motors:
Construction of Induction Motors
Working principle of three phase induction motor
Torque and Torque-Slip characteristics
Transformer Working Video Link
* Need of transformer
In most cases, appliances are manufactured to work
under some specific voltages. Transformers are used to
adjust the voltages to a proper level.
The transformers are the basic components for the
transmission of the electricity.
Transformer is used to increase the voltage at the
power generating station(Step up) and used to decrease
the voltage(Step down) for house hold purpose.

By increasing the voltages the loss of the electricity in


the transmission purpose is minimized.
* Introduction
 Transformer is a static device.
 It transfer electrical energy from one part of the
electrical or electronic circuit to other part of circuit
without changing the frequency.
 It works on the Michal Faradays law of Electromagnetic
Mutual Induction.
WORKING PRINCIPLE
 The transformer works in the principle of mutual induction

“The principle of mutual induction states that when the two coils are
inductively coupled and if the current in coil change uniformly then the
e.m.f. induced in the other coils. This e.m.f can drive a current when a closed
path is provide to it.”

 When the alternating current flows in the


primary coils, a changing magnetic flux is generated around
the primary coil.
 The changing magnetic flux is transferred to the secondary coil
through the iron core
 The changing magnetic flux is cut by the secondary coil, hence
induces an e.m.f in the secondary coil
 Now if load is connected to a secondary winding, this e.m.f
drives a current through it
 The magnitude of the output voltage can be controlled by the
ratio of the no. of primary coil and secondary coil

The frequency of mutually induced e.m.f as same that of the


alternating source which supplying to the primary winding
b
* Construction
Laminated • Cores are designed not to have current in it. But still there is a
leakages current Or the eddy current present in it. To
Core minimize these current the cores are laminated.

• Made up of copper or aluminum coated with


Winding very thin layer of insulation.

• The main function of conservator tank of transformer is to


Tan provide adequate space for expansion of oil inside the
transformer. It is usually Cylindrical or cubical.
k
Isolation • It is provided by using Synthetic Oil between
Core
and Tank.
• When the temperature changes occur in Transformer insulating oil, the
Breather oil expands or contracts and there an exchange of air also occurs when
transformer is fully loaded. When transformer gets cooled, the oil level
goes down and air gets absorbed within.
* Types of Transformers
Transformer

Basis of Basis of coolant


Basis of Winding
Construction material used

Core type Step up Oil filled self


transformer transformer cooling

Shell type Step down Oil filled


transformer transformer water cooling

Spiral core Isolation


Air blast
transformer transformer
CONSTRUCTION OF TRANSFORMER
 These are two basic of transformer construction
 Magnetic core

 Windings or coils

 Magnetic core

 The core of transformer either square or


rectangular type in size
 It is further divided into two parts vertical and horizontal

 The vertical portion on which coils are


wounds called limb while horizontal portion is called
yoke. these parts are
 Core is made of laminated core type
constructions, eddy
current losses get minimize.
 Generally high grade silicon steel laminations (0.3 to 0.5mm)
WINDING
 Conducting material is used in the winding of the transformer
 The coils are used are wound on the limbs and insulated from
each other
 The two different windings are wounds on two different limbs

 The leakage flux increases which affects the performance and


efficiency of transformer
 To reduce the leakage flux it is necessary that the windings
should be very close to each other to have high mutual
induction
CORE TYPE CONSTRUCTION

 In this one magnetic circuit and cylindrical coils are


used
 Normally L and T shaped laminations are used
 Commonly primary winding would on one limb while
secondary on the other but performance will be reduce
 To get high performance it is necessary that other the two
winding should be very close to each other
SHELL TYPE CONSTRUCTION

 In this type two magnetic circuit are used


 The winding is wound on central limbs

 For the cell type each high voltage winding lie between
two voltage portion sandwiching the high voltage winding
 Sub division of windings reduces the leakage flux

 Greater the number of sub division lesser the reactance

 This type of construction is used for high voltage


* Basis of Windings
*Step up Transformer: The no of
windings on Primary side is less than the
no. of windings on the secondary side.
Np < Ns
*Step down Transformer: The no. of
winding on Primary side are more than
the no. of windings on the secondary side.
Np > Ns
*Isolation Transformer: The no. of
winding on Primary side are equal to the
no. of windings on the secondary side.
Np = Ns
* Basis of coolant
*Oil filled self cooling: Oil filled self cooled type uses small and
medium-sized distribution transformers. The assembled windings
and core of such transformers are mounted in a welded, oil-tight steel
tanks provided with a steel cover.. The oil helps in transferring the
heat from the core and the windings to the case from where it is
radiated out to the surroundings.
*Oil filled water cooled: This type is used for much more
economic construction of large transformers. The cooling coil is
mounted near the surface of the oil, through which cold water keeps
circulating. This water carries the heat from the device.
*Air Blast: This type is used for transformers that use voltages
below 25,000 volts. The transformer is used at houses.
* Applications
1. Transmitting electrical energy over long distances
through wires.
2. Transformers with several secondary's are used in
television and radio receivers where several
different voltages are required.
3. Used as voltage regulator
4. Used almost everywhere in day to day life.
* Auto Transformer
The autotransformer has only one winding. The
winding is common to both the primary and the secondary
one.
The working principle is same as that of normal
transformer difference is that it has one winding divided into
primary and secondary.
Advantages:
Less costly
Better regulation
Low losses as compared to ordinary two winding
transformer of the same rating.
Disadvantages;
An autotransformer does not provide electrical isolation
between its windings.
 The secondary winding is not insulated from the
primary winding.
 Used only in the limited places where a slight variation
of
the output voltage from input voltage is required.

 Applications
 It is used as a starter to give upto 50 to 60% of full
voltage to the stator of a squirrel cage induction motor
during starting.
 It is used to give a small boost to a distribution cable, to
correct the voltage drop.
 Changing fan speed over a narrow range.

You might also like