Electronic Product Assembly
and Servicing
EPAS Specialization Grade- 12
CHESTER ALLAN M. MENDEZ
Subject Teacher
• Most Essential Learning Competency 1 – Prepare to Assemble
Electronics Products (TLE_IAEPAS9- 12AEP-IVa-27)
• 1.1. Prepare assembly workplace in accordance with OHS policies and
procedures
• 1.2. Check required materials, tools, and equipment in accordance with
established procedures
Parts of Module
• Expectations - These are what you will be able to know after completing the lessons
in the module.
• Pre-test - This will measure your prior knowledge and the concepts to be mastered
throughout the lesson.
• Looking Back to your Lesson - This section will measure what learnings and skills did
you understand from the previous lesson.
• Brief Introduction- This section will give you an overview of the lesson.
• Activities - This is a set of activities you will perform with a partner.
• Remember - This section summarizes the concepts and applications of the lessons.
• Check your Understanding- It will verify how you learned from the lesson.
• Post-test - This will measure how much you have learned from the entire module.
1.1. Prepare assembly workplace in
accordance with OHS policies and
procedures
• EXPECTATIONS:
1. Identify occupational health and safety
2. Determine the workplace hazards
3. Differentiate the types of hazards
4. Explain the risk assessment
5. Explain WEEE
6. Discuss the 3R
7. Practice 5S in Workplace
8. Identify the importance of PPE
Pre-Test
• Direction: Read the questions carefully and encircle the letter of the correct answer.
1. OHS stands for what?
A. Occupation Healthy Safety C. Occupational Health and Safety
B. Occupational Healthy Services D. Occupation Health and Services
2. Anything that can cause injury, illness, damage to property or loss of material.
C. Chemicals C. Hazards
D. Danger D. Risks
3. The chance of the worker being harmed by the hazard.
E. Chemicals C. Hazards
F. Danger D. Risk
4. A systematic examination of a task, job or process that you carry out
at work for the purpose of identifying the significant hazards.
A. Risk Control C. Risk Management
B. Risk Identification D. Risk Managing
5. A type of occupational hazard caused by exposure to chemicals in
the workplace.
C. Chemical Hazard C. Electrical Hazard
D. Biological Hazard D. Physical Hazard
6. ____________ is used to drive or fasten negative slotted screws.
E. Flat Screwdirver C. Precision Screwdriver
F. Phillips Screwdriver D. Stubby Screwdriver
7. _____________ is used in removing soldered wires and components
on printed circuit boards for troubleshooting the repair purposes.
A. Desoldering Tool C. Soldering Lead
B. Soldering Iron D. Soldering Tool Stand
8. ___________ is a wire-cutting pliers, though they are not used to
grab or turn anything but are used to cut wires.
C. Combination Pliers C. Side Cutter
D. Long Nose Pliers D. Wire Stripper
9. ____________ is used to bore or drill holes in the printed circuit
board (PCB) with sizes from 1/32” – 1/16”.
E. Drill bit C. Metal Files
F. B. Mini-Drill D. Portable Drill
10. ____________ is a common tool used in cutting various trades and crafts for a
variety of purposes.
A. Hacksaw C. Third Hand
B. B. Magnifying Glass D. Utilitiy Knife
11-13. What are the three function of VOM? (choose 3)
C. Ammilimeter D. Ohmmeter
D. Milliammeter E. Voltage meter
E. Millimeter F. Voltmeter
14. It is a device which produces simple wave forms.
F. DC Powersupply C. Signal Generator
G. B. Oscilloscope D. VOM
15. A piece of electronic test equipment that allows signal voltages to be view.
H. DC Powersupply C. Signal Generator
I. B. Oscilloscope D. VOM
Direction: Use the clues below to fill in the crossword puzzle with the
correct words
TOPIC: WEEE, 3R, 5S and PPE
• Objectives:
1. Explain WEEE
2. Discuss the 3R
3. Practice 5S in Workplace
4. Identify the importance of PPE
