4G PMR SINGLE SITE OPTIMISATION

Check list activities GO/No GO (L1 Optimization)

1. Healthy Check: availability
2. Alarm clear PLR
3. RETU  must be in proper setting
4. Overshooting (TA), ISD, blocking
5. UL RSSI vs SINR
6. Neighbouring (cell pair HO, LNADJx, LNREL, ANR, ADJx, etc) & X2 available
7. Justification if not KPI achieve
8. Tracker Activity, starting from D-0

• All optim activity (NCR, escalation issue, etc) should put Nokia Regional Optim team
in to CC
• Inform site owner to Nokia Regional Optim team.
HOSR JUSTIFICATION

Mandatory Check :
- Site Health check (Alarm, config based NDB,etc)
- Neighbors creation ( LNADJ/LNADJL, LNREL, ANR uebased enable)
- Conscheck Intra Frequency Handover parameter (threshold1, A3 &
A5 event, etc)
- Conscheck Inter Frequency Handover parameter (LNHOIF, UFFIM,
IRFIM, Less priority due to focus on intrafreq HOSR, etc)
- Handover parameters see Page 5
HOSR IMPROVEMENT ACTION
1. Trace worst cell pair contributor : 4. Check overshooting :
• RSLTE031 Check High attempts , Low SR • Timing advance
target cell at cell pair. intrafreqAttempts • Cell to cell distance
<600 go exclusion 5. Coverage Tuning:
2. Check neighbouring : • Down Tilt RET overshooting Source or
• Neighbour creation (delete Target
LNADJ/LNADJL/LNREL- create by ANR) • Down/up Manual tilt : ET / MT (Max 8/10)
• PCI collision & PCI conflict • Power reduction setting (dlrsboost =700
• Blacklisting Target Cells (3dB))
• Adjust ANRPL (anrThresRSRPNbCellMobEv 6. Parameter tunning
= -95dBm) • CIO Tunning If target cell high utilised
3. Healthy check target cell • Pairing need to be tuned (cellIndOffNeigh)
• Alarm : S1 SCTP fail, GTPU fail, Operation • Initial agresive parameter tuning (Page 6)
Degrade ( alarm direct impact to
availability)
• Transport issue : packet loss, high
utilisation
Note : Mandatory to capture track of action at chart performance report (add line at chart show the action)
 EXCLUSION CRITERION – LOW ATTEMPTS
Low Call Attempts - Exclusion Criteria
Low Call Attempt - Criteria 1: Criteria 2: Criteria 3:
KPI Name PMR KPI Target
Exception Criteria's Higher imit for Low Attempts Lower Limit for KPI Target Higher Limit for Fail count
2G CSSR 94% Ongoing 2250 80% 206
2G DCR 2.5% Ongoing 100 15% 10
2G HOSR 93% Ongoing 80 80% 10

Low Call Attempt - Criteria 1: Criteria 2: Criteria 3:

KPI Name PMR KPI Target
Exception Criteria's Higher imit for Low Attempts Lower Limit for KPI Target Higher Limit for Fail count
3G CSSR CS 97% Agreed 100 85% 10
3G CSSR PS 97% Agreed 2000 90% 160
3G CDR CS 2% Agreed 100 10% 10
3G CDR PS 2% Agreed 3000 10% 200
3G SHO 95% Agreed 2000 90% 160

Low Call Attempt - Criteria 1: Criteria 2: Criteria 3:

KPI Name PMR KPI Target
Exception Criteria's Higher imit for Low Attempts Lower Limit for KPI Target Higher Limit for Fail count
4G CSSR 97% Agreed 4000 92% 400
4G DCR 2% Agreed 3000 5% 150
4G HOSR 95% Agreed 600 80% 50
AGGRESIVE PARAMETER TUNING
MO Parameter GP Aggressive Setting REMARK
SIB qrxlevmin -124 -110 Increase for better Coverage
LNCEL threshold3 30 30 Increase value for aggressive trigger HO Serving Cell - Intra HO Coverage HO A5
LNCEL threshold3a 32 33 Increase value for better Neighbour Target Cell - Intra HO Coverage HO A5
LNCEL a3Offset 6 6 Increase value for better Neighbour Target Cell - Intra HO Better Cell HO A3
SIB sNonIntrsearch 10 10 Increase value for Immediate measurement of InterFreq or InterRat
IRFIM qRxLevMinInterF -124 -110 Increase for better Neighbour Target Cell Coverage Inter Freq
IRFIM qRxLevMinInterF -124 -110 Increase for better Neighbour Target Cell Coverage Inter Freq
IRFIM qRxLevMinInterF -124 -110 Increase for better Neighbour Target Cell Coverage Inter Freq
UFFIM utraFrqThrL 6 12 Increase for better Neighbour Target Coverage
LNCEL hysThreshold2InterFreq 0 0 Increase value for Immediate measurement of InterFreq Coverage HO A2
LNCEL threshold2InterFreq 28 34 Increase value for Immediate measurement of InterFreq Coverage HO A2
LNCEL threshold2a 31 38 Increase value for Immediate stop measurement of InterFreq Coverage HO A1
LNHOIF threshold3InterFreq 25 if L18 or L21 then 34, if L9 then 30 Increase value for aggressive trigger HO InterFreq Coverage HO A5
LNHOIF threshold3InterFreq 25 if L18 or L21 then 34, if L9 then 30 Increase value for aggressive trigger HO InterFreq Coverage HO A5
LNHOIF threshold3InterFreq 25 if L18 or L21 then 34, if L9 then 30 Increase value for aggressive trigger HO InterFreq Coverage HO A5
LNHOIF threshold3aInterFreq 27 36 Increase for better Neighbour Target Cell InterFreq Coverage HO A5
LNHOIF threshold3aInterFreq 27 36 Increase for better Neighbour Target Cell InterFreq Coverage HO A5
LNHOIF threshold3aInterFreq 27 36 Increase for better Neighbour Target Cell InterFreq Coverage HO A5
LNCEL_FDD dlRsBoost 1000 700 reduce coverage 3dB
LNREL handoverAllowed 0 1 Black List NREL for selective Neighbour Only (High PLR,HW problem)
LNREL nrControl 0 1 Black List NREL for selective Neighbour Only (High PLR,HW problem)
LNREL removeAllowed 1 0 Black List NREL for selective Neighbour Only (High PLR,HW problem)
RETU angle 2 Degree Add 2 -4 Deg (Max tilt 8 deg) Reduce Overshooting. Done in Source and target Cell
ANRPL anrThresRSRPNbCellMobEv -95 add only strongest neighbor by Mobility event
BETTER CELL HANDOVER
• Better Cell Handover aims to keep the UE always on best cell
(measured by RSRP)
• Based on 3GPP reporting event “A3”:
- Event A3 defines relative offset LNCEL: a3-offset
- Timer to Trigger LNCEL: a3-TimeToTrigger
- Reporting Interval LNCEL: a3-ReportInterval

RSRP at serving cell + a3Offset < RSRP at neighbor cell

• Better Cell Handover can be enabled / disabled:

enableBetterCellHo
LNCEL; 0 (false), 1 (true); 1 (true)
 Handovers Event A3 used for Better Cell HO
RSRP at serving cell + a3Offset < RSRP at neighbor cell
a3Offset
LNCEL; -15..15dB; 0.5dB; -
RSRP
A3 condition met RSRP Neighbor Cell

a3ReportInterval
a3offset LNCEL; 120ms (0), 240ms (1),
480ms (2), 640ms (3), 1024ms
(4), 2048ms (5), 5120ms (6),
Serving Cell RSRP 10240ms (7), 1min (8), 6min (9),
12min (10), 30min (11), 60min
(12); -
time
a3TimeToTrigger a3TimeToTrigger a3Report Interval
LNCEL; 0ms (0), 40ms (1), 64ms
(2), 80ms (3), 100ms (4), 128ms Measurement Measurement
(5), 160ms (6), 256ms (7), 320ms Report Report
(8), 480ms (9), 512ms (10), 640ms reporting condition met
(11), 1024ms (12), 1280ms (13), eNB
after Time To Trigger
2560ms (14), 5120ms (15); -
Coverage Handover
• Coverage Handover is used to HO to other eUTRA cell in case:
• serving cell RSRP gets below an absolute threshold and (&&)
• neighbor cell RSRP gets better than an absolute threshold
• Based on 3GPP reporting event “A5”:
- 3GPP ”hresholdEUTRA” used to define absolute RSRP level for
a) serving cell: LNCEL: threshold3 and
b) neighbor cell: LNCEL: threshold3a
- Timer to Trigger LNCEL: a5-TimeToTrigger
- Reporting Interval LNCEL: a5-ReportInterval
• Coverage Handover can be enabled / disabled:
enableCovHo
LNCEL; 0 (false), 1 (true); 1
(true)
 Handovers Event A5 threshold3
LNCEL; 0..97dB; 1dB; -
Coverage RSRP at serving cell < threshold3 Baseline is -140dBm
Handover
AND (&&)
RSRP threshold3a
RSRP at target > threshold3a LNCEL; 0..97dB; 1dB; -
Baseline is -140dBm
Serving Cell RSRP threshold3a

threshold3
threshold3a
threshold3

Neighbor Cell RSRP time

a5TimeToTrigger a5TimeToTrigger a5Report Interval

LNCEL; 0ms (0), 40ms (1), 64ms Measurement Measurement
a5ReportInterval Report Report
(2), 80ms (3), 100ms (4), 128ms
(5), 160ms (6), 256ms (7), LNCEL; 120ms, 240ms,
320ms (8), 480ms (9), 512ms 480ms, 640ms, 1024ms,
-140 dBm (10), 640ms (11), 1024ms (12), 2048ms, 5120sm, 10240ms, eNB
1280ms (13), 2560ms (14), 1min, 6min, 12min, 30min,
5120ms (15); - 60min; -
UL RSSI IMPROVEMENT ACTION
1. All main KPI achieved, go for exclusion 4. High UL RSSI >-105
criterion - Check hourly performance UL
• Min ULRSSI : <= -107 dBm RSSI, if the figure is steady all hours
• Payload same time stamp min UL and not follow the traffic loading,
RSSI >= 3 GB check SINR <=0, escalated to project
2. UL RSSI -108~-109 dBm adjust to check installation and interference
p0NomPusch = -110 dBm issue
3. If UL RSSI - > 108 dBm adjust 5. Set ulpcLowlevSch from -103 to -
p0NomPusch 110/-114
• Power reduction setting (dlrsboost
=700 (3dB))