Scribd
Upload
55 views

Sequential Circuit Analysis

Sequential circuit analysis involves using state tables or state diagrams to show the inputs, outputs, current states, and next states of a circuit. State tables are analogous to truth tables for combinational circuits. They are used to determine the flip-flop input values needed to generate the next states based on the present states and inputs. Finally, flip-flop characteristic tables or equations are used to find the actual next states.

Uploaded by

mankinda
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
55 views

Sequential Circuit Analysis

Sequential circuit analysis involves using state tables or state diagrams to show the inputs, outputs, current states, and next states of a circuit. State tables are analogous to truth tables for combinational circuits. They are used to determine the flip-flop input values needed to generate the next states based on the present states and inputs. Finally, flip-flop characteristic tables or equations are used to find the actual next states.

Uploaded by

mankinda
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 13

Sequential Circuit Analysis

State tables show the inputs, outputs, and flip-flop state changes
for sequential circuits. State diagrams are an alternative but equivalent way of showing the same information.

Inputs

Combinational circuit Memory

Outputs

Sequential circuit analysis

How do you analyze a sequential circuit?



For a combinational circuit we could find a truth table, which shows how the outputs are related to the inputs. A state table is the sequential analog of a truth table. It shows inputs and current states on the left, and outputs and next states on the right. For a sequential circuit, the outputs are dependent upon not only the inputs, but also the current state of the flip-flops. In addition to finding outputs, we also need to find the state of the flip-flops on the next clock cycle.

Sequential circuit analysis

Flip-flop input equations

Finding the next states is harder. To do this, we have to figure out how the flip-flops are changing. Step 1: Find Boolean expressions for the flip-flop inputs. I.e. How do the inputs (say, J & K) to the flip-flops depend on the current state and input Step 2: Use these expressions to find the actual flip-flop input values for each possible combination of present states and inputs. I.e. Fill in the state table (with new intermediate columns) Step 3: Use flip-flop characteristic tables or equations to find the next states, based on the flip-flop input values and the present states.

Sequential circuit analysis

Derive the state table and state diagram.


X Y D X Y X B D Q C Z B X' A C Q A

Sequential circuit analysis

Derive the state diagram


J1

J
Q1

K 0 1 0 1

Q (t+1) Q (t) 0 1 Q (t)

Ope ration No change Re t se St e Comple nt me

J1 K1

S J Q C KR Q

Q0

J Q C K2 K R Q

J2

0 0 1 1
Z

Sequential circuit analysis

Step 3: Find the next states



Finally, use the JK flip-flop characteristic tables or equations to find the next state of each flip-flop, based on its present state and inputs. The general JK flip-flop characteristic equation is: Q(t+1) = KQ(t) + JQ(t) In our example circuit, we have two JK flip-flops, so we have to apply this equation to each of them: Q1(t+1) = K1Q1(t) + J1Q1(t) Q0(t+1) = K0Q0(t) + J0Q0(t)

We can also determine the next state for J K each input/current state combination 0 0 directly from the characteristic table.
0 1 1
Sequential circuit analysis

Q (t+1) Q (t) 0 1 Q (t)

Ope ration No change Re t se St e Comple nt me


6

1 1

Sequential circuit design procedure


Step 1: Make a state table based on the problem statement. The table should show the present states, inputs, next states and outputs. (It may be easier to find a state diagram first, and then convert that to a table.) Step 2: Assign binary codes to the states in the state table, if you havent already. If you have n states, your binary codes will have at least log2 n digits, and your circuit will have at least log2 n flip-flops. Step 3: For each flip-flop and each row of your state table, find the flip-flop input values that are needed to generate the next state from the present state. You can use flip-flop excitation tables here. Step 4: Find simplified equations for the flip-flop inputs and the outputs. Step 5: Build the circuit!
Sequential circuit analysis 7

Class example revisited


1) Find non overlapping sequence: 1001. Design using D-flipflops.

Sequential circuit analysis

Blank Sheet
Q (t) 0 0 1 1 Q (t+1) 0 1 0 1 D 0 1 0 1 Ope ation r Re t se St e Re t se St e

Sequential circuit analysis

Design a twos complementer using J-K flip-flops

Input:X,Y. Input Sequence: a binary number of arbitrary length. Sequence represented by sequential values of X. Output: Z, the corresponding bit in the twos complement. When y=1 => the sequence is complete, Y=0 => Sequence ongoing.
Solution: The trick is in identifying that whenever we compute a 2's complement, we complement each bit and add a 1. So as long as we keep receiving 0's, we complement them to convert to 1's and then we add a 1. So until we hit our first 1, we stay on the same state outputting 0's. As soon as we hit a 1, the complement for that is a 0 to which we add a 1 getting a 1. And then we have no carry so we move onto a state where we just complement each bit we receive.

Sequential circuit analysis

10

Blank Sheet
Q(t) 0 0 1 1 Q(t+1) 0 1 0 1 J 0 1 x x K x x 1 0 Operation No change/reset Set/complement Reset/complement No change/set

Sequential circuit analysis

11

Excitation tables for all flip-flops


Q (t) 0 0 1 1 Q (t+1) 0 1 0 1 D 0 1 0 1 Ope ration Re t se St e Re t se St e

Q (t) 0 0 1 1

Q (t+1) 0 1 0 1

J 0 1 x x

K x x 1 0

Ope ration No change se /re t S t/comple nt e me Re t/comple nt se me No change t /se

Q (t) 0 0 1 1

Q (t+1) 0 1 0 1

T 0 1 1 0

Ope ration No change Comple nt me Comple nt me No change


12

Sequential circuit analysis

Summary

The basic sequential circuit design procedure: Make a state table and, if desired, a state diagram. This step is usually the hardest. Assign binary codes to the states if you didnt already. Use the present states, next states, and flip-flop excitation tables to find the flip-flop input values. Write simplified equations for the flip-flop inputs and outputs and build the circuit. Next, well look at common examples of sequential circuits, including different types of counters.

Sequential circuit analysis

13

You might also like