8086 instruction set

• The 8086 microprocessor supports 8 types of instructions −

• Data Transfer Instructions
• Arithmetic Instructions
• Bit Manipulation Instructions
• String Instructions
• Program Execution Transfer Instructions (Branch & Loop Instructions)
• Processor Control Instructions
• Iteration Control Instructions
• Interrupt Instructions
Data Transfer Instructions

• These instructions are used to transfer the data from the source operand to the
destination operand.
• Instruction to transfer a word
• MOV − Used to copy the byte or word from the provided source to the provided
destination.
• PPUSH − Used to put a word at the top of the stack.
• POP − Used to get a word from the top of the stack to the provided location.
• PUSHA − Used to put all the registers into the stack.
• POPA − Used to get words from the stack to all registers.
• XCHG − Used to exchange the data from two locations.
• XLAT − Used to translate a byte in AL using a table in the memory.
• Instructions for input and output port transfer
• IN − Used to read a byte or word from the provided port to the accumulator.
• OUT − Used to send out a byte or word from the accumulator to the provided
port.
• Instructions to transfer the address
• LEA − Used to load the address of operand into the provided register.
• LDS − Used to load DS register and other provided register from the memory
• LES − Used to load ES register and other provided register from the memory.
• Instructions to transfer flag registers
• LAHF − Used to load AH with the low byte of the flag register.
• SAHF − Used to store AH register to low byte of the flag register.
• PUSHF − Used to copy the flag register at the top of the stack.
• POPF − Used to copy a word at the top of the stack to the flag register.
Arithmetic Instructions

• Instructions to perform addition

• ADD − Used to add the provided byte to byte/word to word.
• ADC − Used to add with carry.
• INC − Used to increment the provided byte/word by 1.
• AAA − Used to adjust ASCII after addition.
• DAA − Used to adjust the decimal after the addition/subtraction
operation.
• Instructions to perform subtraction
• SUB − Used to subtract the byte from byte/word from word.
• SBB − Used to perform subtraction with borrow.
• DEC − Used to decrement the provided byte/word by 1.
• NPG − Used to negate each bit of the provided byte/word and add
1/2’s complement.
• CMP − Used to compare 2 provided byte/word.
• AAS − Used to adjust ASCII codes after subtraction.
• DAS − Used to adjust decimal after subtraction.
• Instruction to perform multiplication
• MUL − Used to multiply unsigned byte by byte/word by word.
• IMUL − Used to multiply signed byte by byte/word by word.
• AAM − Used to adjust ASCII codes after multiplication.
• Instructions to perform division
• DIV − Used to divide the unsigned word by byte or unsigned double
word by word.
• IDIV − Used to divide the signed word by byte or signed double word by
word.
• AAD − Used to adjust ASCII codes after division.
• CBW − Used to fill the upper byte of the word with the copies of sign bit
of the lower byte.
• CWD − Used to fill the upper word of the double word with the sign bit
of the lower word.
Bit Manipulation Instructions

• These instructions are used to perform operations where data bits are
involved, i.e. operations like logical, shift, etc.
• Instructions to perform logical operation
• NOT − Used to invert each bit of a byte or word.
• AND − Used for adding each bit in a byte/word with the corresponding bit in
another byte/word.
• OR − Used to multiply each bit in a byte/word with the corresponding bit in
another byte/word.
• XOR − Used to perform Exclusive-OR operation over each bit in a byte/word
with the corresponding bit in another byte/word.
• TEST − Used to add operands to update flags, without affecting operands.
• Instructions to perform shift operations
• SHL/SAL − Used to shift bits of a byte/word towards left and put
zero(S) in LSBs.
• SHR − Used to shift bits of a byte/word towards the right and put
zero(S) in MSBs.
• SAR − Used to shift bits of a byte/word towards the right and copy the
old MSB into the new MSB.
• Instructions to perform rotate operations
• ROL − Used to rotate bits of byte/word towards the left, i.e. MSB to
LSB and to Carry Flag [CF].
• ROR − Used to rotate bits of byte/word towards the right, i.e. LSB to
MSB and to Carry Flag [CF].
• RCR − Used to rotate bits of byte/word towards the right, i.e. LSB to
CF and CF to MSB.
• RCL − Used to rotate bits of byte/word towards the left, i.e. MSB to CF
and CF to LSB.
String Instructions

• String is a group of bytes/words and their memory is always allocated in a sequential order.
• REP − Used to repeat the given instruction till CX ≠ 0.
• REPE/REPZ − Used to repeat the given instruction until CX = 0 or zero flag ZF = 1.
• REPNE/REPNZ − Used to repeat the given instruction until CX = 0 or zero flag ZF = 1.
• MOVS/MOVSB/MOVSW − Used to move the byte/word from one string to another.
• COMS/COMPSB/COMPSW − Used to compare two string bytes/words.
• INS/INSB/INSW − Used as an input string/byte/word from the I/O port to the provided memory
location.
• OUTS/OUTSB/OUTSW − Used as an output string/byte/word from the provided memory location
to the I/O port.
• SCAS/SCASB/SCASW − Used to scan a string and compare its byte with a byte in AL or string word
with a word in AX.
• LODS/LODSB/LODSW − Used to store the string byte into AL or string word into AX.
Program Execution Transfer Instructions (Branch and
Loop Instructions)

• These instructions are used to transfer/branch the instructions during

an execution. It includes the following instructions −
• Instructions to transfer the instruction during an execution without
any condition −
• CALL − Used to call a procedure and save their return address to the
stack.
• RET − Used to return from the procedure to the main program.
• JMP − Used to jump to the provided address to proceed to the next
instruction.
• Instructions to transfer the instruction during an execution with some conditions
• JA/JNBE − Used to jump if above/not below/equal instruction satisfies.
• JAE/JNB − Used to jump if above/not below instruction satisfies.
• JBE/JNA − Used to jump if below/equal/ not above instruction satisfies.
• JC − Used to jump if carry flag CF = 1
• JE/JZ − Used to jump if equal/zero flag ZF = 1
• JG/JNLE − Used to jump if greater/not less than/equal instruction satisfies.
• JGE/JNL − Used to jump if greater than/equal/not less than instruction satisfies.
• JL/JNGE − Used to jump if less than/not greater than/equal instruction satisfies.
• JLE/JNG − Used to jump if less than/equal/if not greater than instruction satisfies.
• JNC − Used to jump if no carry flag (CF = 0)
• JNE/JNZ − Used to jump if not equal/zero flag ZF = 0
• JNO − Used to jump if no overflow flag OF = 0
• JNP/JPO − Used to jump if not parity/parity odd PF = 0
• JNS − Used to jump if not sign SF = 0
• JO − Used to jump if overflow flag OF = 1
• JP/JPE − Used to jump if parity/parity even PF = 1
• JS − Used to jump if sign flag SF = 1
Processor Control Instructions

• These instructions are used to control the processor action by

setting/resetting the flag values.
• STC − Used to set carry flag CF to 1
• CLC − Used to clear/reset carry flag CF to 0
• CMC − Used to put complement at the state of carry flag CF.
• STD − Used to set the direction flag DF to 1
• CLD − Used to clear/reset the direction flag DF to 0
• STI − Used to set the interrupt enable flag to 1, i.e., enable INTR input.
• CLI − Used to clear the interrupt enable flag to 0, i.e., disable INTR input.
Iteration Control Instructions

• These instructions are used to execute the given instructions for

number of times.
• LOOP − Used to loop a group of instructions until the condition
satisfies, i.e., CX = 0
• LOOPE/LOOPZ − Used to loop a group of instructions till it satisfies ZF
= 1 & CX = 0
• LOOPNE/LOOPNZ − Used to loop a group of instructions till it satisfies
ZF = 0 & CX = 0
• JCXZ − Used to jump to the provided address if CX = 0
Interrupt Instructions

• These instructions are used to call the interrupt during program

execution.
• INT − Used to interrupt the program during execution and calling
service specified.
• INTO − Used to interrupt the program during execution if OF = 1
• IRET − Used to return from interrupt service to the main program
Addressing modes in 8086
microprocessor
• The way of specifying data to be operated by an instruction is known
as addressing modes. This specifies that the given data is an
immediate data or an address. It also specifies whether the given
operand is register or register pair.
• Types of addressing modes:
• Register mode – In this type of addressing mode both the operands
are registers.
Example: MOV AX,BX
• XOR AX,DX
• ADD AL,BL
• Immediate mode – In this type of addressing mode the source
operand is a 8 bit or 16 bit data. Destination operand can never be
immediate data.
Example: MOV AX,2000
• MOV CL, 0A
• ADD AL, 45
• AND AX, 0000
• to initialize the value of segment register an register is required.
• MOV AX,2000
• MOV CS,AX
• Displacement or direct mode –
• In this type of addressing mode the effective address is directly given
in the instruction as displacement.
Example:
• MOV AX, [DISP]
• MOV AX, [0500]
• Register indirect mode – In this addressing mode the effective
address is in SI, DI or BX.
Example: Physical Address = Segment Address + Effective Address
• MOV AX,[DI]
• ADD AL, [BX]
• MOV AX, [SI]
• Based indexed mode – In this the effective address is sum of base
register and index register.
• Base register : BX, BP
• Index register : SI,DI
• The physical memory address is calculated according to the base
register.
• Example: MOV AL, [BP+SI]
• MOV AX, [BX+DI]
• Indexed mode – In this type of addressing mode the effective address
is sum of index register and displacement.
• Example: MOV AX, [SI+2000]
• MOV AL, [DI+3000]
• Based mode – In this the effective address is the sum of base register
and displacement.
Example: MOV AL, [BP+0100]
• Based indexed displacement mode – In this type of addressing mode
the effective address is the sum of index register, base register and
displacement.
Example: MOV AL, [SI+BP++2000]
• String mode – This addressing mode is related to string instructions.
In this the value of SI and DI are auto incremented and decremented
depending upon the value of directional flag.
Example: MOVS B
• MOVS W
• Input/Output mode – This addressing mode is related with input
output operations.
Example: IN A, 45
• OUT A, 50
• Relative mode –
In this the effective address is calculated with reference to instruction
pointer.
Example: JNZ 8 bit address
• IP = IP+ 8 bit address