Week 4 Part 1
1. What is the lightest known metal?
A. mercury
B. Steel
C. Chromium
D. aluminum
2. Material having a high electrical resistance and should not be
used as conductor of electrical current.
a. Magnesium
b. Copper
c. Nickel
d. iron
3. The property that characterizes a materials ability to be drawn
into a wire is known as:
a. Plasticity
b. Elasticity
c. Ductility
d. utility
4. Stress relieving is also_________ for the purpose of reducing
the internal stress of steel material/ metal.
a. Quenching
b. Normalizing
c. Tempering
d. drawing
5. A carbon content in the range of ____ in steel readily
responds to heat treatment
a. 0.35 to 0.40 % C
b. 0.28 to 0.30 % C
c. 0.18 to 0.25 % C
d. 0.12 to 0.15 % C
6.It indicates how many times a volume of material is heavier
than an equal volume of water.
a. Specific gravity
b. Specific volume
c. Specific weight
d. Specific density
7. Nickel;- chromium- Molybdenum steel designation SAE_____
a. 81xx
b. 74xx
c. 94xx
d. 64xx
8. Moment of inertia is also called
a. Modulus of elasticity
b. Weep strength
c. Radius of gyration
d. None of the above
9. It is hardening treatment whereby a cast metal is being heated
to a very high temperature then suddenly subjected to rapid
cooling to improve hardenability of wear resistance is called
a. Annealing
b. Normalizing
c. Tempering
d. quenching
10. A good general purpose deoxidizer which promotes fine
grains in steel.
a. Copper
b. Magnesium
c. Molybdenum
d. silicon
11. Treatment process that produces a residual compressive,
stress at the surface and residual tension on the inside that
results in considerable increase in fatigue strength for members
on torsion/ bending is known as.
a. Partial quenching
b. Heavy oil quenching
c. Quenching
d. Shallow quenching
12. The flux that should be provided in soldering electrical
connection or commutator wires as it tends to corrode the
connections.
a. Sal ammoniac
b. Zinc chloride
c. Stealin
d. Acid flumes
13. The characteristics of toll steel sustain shocks and major
impacts is due to its
a. Toughness
b. Stiffness
c. Ductility
d. machinability
14. The application of electrical current to the corrosion circuit to
counter the corrosion reaction is called.
a. Cathodic protection
b. Sacrificial anodes method
c. Chemical corrosion process
d. Galvanic action
15. A major component of cast steel is
a. Silicon
b. Iron
c. Manganese
d. chromium
16.Normally cast contains 2 % carbon or more and silicon in the
range of ___________ %
a. 1 to 3
b. 1 to 4
c. 2 to 3
d. 1 to 6
17. The material for engine radiation is usually made of
_________
a. Yellow brass
b. Silicon brass
c. Admiralty brass
d. Navy brass
18. A problem by-product used as an electrodes in an electric arc
furnace melting operation is called
a. Anthracite coke
b. Foundry coke
c. Graphite electrodes
d. Bituminous coke
19. Which of the following does not effect the tensile strength of
steel?
a. Sulfur
b. Cobalt
c. Phosphorous
d. boron
20. Alloy steel axle under repeated load/ stress will eventually fall
if the load/ stress is above the endurance for the steel under
consideration. The endurance limit of the steel is.
a. Equal to the allowable stress of the module of elasticity
b. Equal to half of the ultimate strength
c. Equal to module of elasticity
d. Equal to 80 % of the elastic limit
21. Mirror finish has surfaces fitness of ____________ ms
a. 1
b. 2 to 8
c. 1 to 3
d. 2 to 5
22. Chromium steel to include heat and corrosion resistant
designation.
a. SAE 56xx
b. SAE 514xx
c. SAE 61xx
d. SAE 9xx
23. Non- metallic material of high melting temperature being
used as furnace lining
a. Quartz bricks
b. Refractories
c. Silica sand
d. Dolomile clay bricks
24. In greater quantity this element is harmful to the molten
ferrous metal.
a. Silicon
b. Aluminum
c. Oxides
d. sulfur
25. Silicon- manganese steel designation, SAE ________
a. 72xx
b. 40xx
c. 92xx
d. 9xx
26. Cold drawing is also called
a. Hard drawn
b. Oxidized steel
c. Cold lap steel
d. Strain hardening
27. The brittleness in steel at elevated temperature is known as
a. Hard drawn
b. Cold lap
c. Red shortness
d. Residual stresses
28. Material may be stretched and still returns to its former form/
condition upon release of force is called
a. Plasticity
b. Modulus of elasticity
c. Ductility
d. Elastic limit
29. A ____ is a thread that has a lead
equal to pitch.
A. Right hand thread
B. Left hand thread
C. Single thread
D. Multiple thread
30. Distance between the crest and the base of the
thread, measured perpendicular to the axis.
A. Depth of thread
B. Length of engagement
C. Depth of engagement
D. Axis of thread
31. Used to permit lever shift for vertical travel of rail.
A. Ball crank
B. Clamp plates
C. Plunger knob
D. None of the above
32. It is mounted at the top of the column and is
guided in perfect alignment by the machined
dovetailed surfaces.
A. Over arm
B. Spindle
C. Arbor
D. Saddle
33. Refers to circular milling attachment that is bolted
to the top of the table of a plain or universal milling
machine.
A. Slotting attachment
B. Rotary attachment
C. Milling attachment
D. Spiral attachment
34. The process of removing burrs and the gates and
risers left on casting after the molding process.
A. Reaming
B. Snagging
C. Honing
D. Knurling
35. The _____ supports the table on the cross rail and
moves across it from left to right.
A. Apron
B. Bearing
C. Spindle
D. Handle
36. Name of mechanism, which a welding operator
holds during gas welding and at the end of which the
gases are burred to perform various gas welding
operation.
A. Hose
B. Torch
C. Gage
D. Switch
37. A tool used for measuring diameters.
A. Protractor
B. Scribber
C. Caliper
D. Compass
38. A fine grained, slaty silica rock used for sharpening
edged tools.
A. Oilstone
B. Surface grinder
C. Rocky oil
D. None of the above
39. Device used to prevent leakage of media.
A. Gasket
B. Seal
C. Shield
D. Stopper
40. Flexible material used to seal pressurized fluids
normally under dynamic conditions.
A. Packing
B. Gasket
C. Shield
D. Seal
41. A hand tool used to measure tension on bolts.
A. Tensile range
B. Torque wrench
C. Hooke’s gauge
D. Spring balance
42. A hand tool used to measure engine crank
web deflection.
A. Feeler gage
B. Compound gage
C. Distortion gage
D. Dial gage
43. A device used for accurately measuring
diameters.
A. Dial gage
B. Feeler gage
C. Caliper
D. Micrometer
44. It is used to true and align machine tools, fixtures
and works.
A. Dial indicator
B. Radial indicator
C. Dial gage
D. Feeler gage
45. The operation of making a cone-shaped
enlargement of the end of a hole, as for a recces for a
flattened screw.
A. Counter boring
B. Counter sinking
C. Reaming
D. Drilling
46. A kind of chuck, which has reversible jaws, which
could be adjusted separately.
A. Independent chuck
B. Combination chuck
C. Magnetic chuck
D. Universal chuck
47. It is used for cutting long pieces of metals.
A. Planer
B. Shaper
C. Power saw
D. Broaching machine
48. It is used for external, internal and relieving of
milling cutters and taps.
A. Milling attachment
B. Thread attachment
C. Taper attachment
D. Relieving attachment
49. It is the stretching or spreading of metal by
hammering.
A. Peening
B. Flaring
C. Upsetting
D. Bending
50. The ____ is the most common of the standard
tapers.
A. Brown
B. Jarno
C. Sharpe
D. Morse
