Remote Control 3 Modular Valve
1:1:Collaring
CollaringImpact
ImpactPressure
PressureAdjustment
Adjustment 3:3:Rod
RodRotation
RotationSpeed
SpeedAdjustment
Adjustment
2:2:Drilling
DrillingImpact
ImpactPressure
PressureAdjustment
Adjustment
2
33
Picture
Picture
To Hydraulic Schematic Back Front page Next
Valve location
Remote control 3 modular valve
In the cab Close
Closeview
view
To Hydraulic Schematic Back Front page Next
Close view
Rod rotation speed
Drilling impact adjustment
pressure adjustment
Collaring pressure
adjustment
To Hydraulic Schematic Back Front page Next
1: Collaring Impact
Pressure Adjustment
1: Collaring impact pressure adjustment 1/4
Adjustment procedure
Collaring impact pressure adjustment needs to be adjuste
d to match various rock conditions on the job site.
Obtain proper collaring impact pressure while drilling op
eration.
Factory settings for each model are as follows:
HCR1200: 14 MPa
HCR1500: 14 MPa
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 2/4
1 Push
Pushthe
thehydraulic
hydraulicpressure
pressurecut
cutlever
leverdown.
down.
To Hydraulic Schematic Back Front page Next
1: Collaring impact pressure adjustment 3/4
2 Push the impact switch and set the feed
lever in one gear to the forward position
Impact
switch
* Perform collaring impact pressure adjustment under drilling condition
To Hydraulic Schematic Back Front page Next
1: Collaring impact pressure adjustment 4/4
See the impact pressure gauge in the cab
3 Loosen the lock dial and
adjust the collaring pressure
adjustment valve
Clockwise:
pressure increase
Counterclockwise:
pressure decrease
Factory setting: 14MPa
To Hydraulic Schematic Back Front page Next
2: Drilling Impact Pressure Adjustment
2: Drilling impact pressure adjustment 1/4
Adjustment procedure
Drilling impact pressure adjustment needs to be adjusted to
match various rock conditions on the job site.
Obtain proper impact pressure while drilling operation.
Factory settings for each model are as follows
HCR1200: 17.5 MPa
HCR1500: 17.5 MPa
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 2/4
1 Push
Pushthe
thehydraulic
hydraulicpressure
pressurecut
cutlever
leverdown.
down.
To Hydraulic Schematic Back Front page Next
2: Drilling impact pressure adjustment 3/4
2 Push the impact switch and set the feed
lever in two-gear to the forward position
Impact
switch
* Perform drilling impact pressure adjustment under drilling condition
To Hydraulic Schematic Back Front page Next
2: Drilling impact pressure adjustment 4/4
See the impact pressure gauge in the cab
3 Loosen the lock dial and
adjust the collaring pressure
adjustment valve
Clockwise:
pressure increase
Counterclockwise:
pressure decrease
Factory setting: 14MPa
To Hydraulic Schematic Back Front page Next
3: Rod Rotation Speed Adjustment
3: Rod rotation speed adjustment 1/5
Adjustment procedure
Rod rotation speed adjustment need to be adjusted to match
various rock conditions on the job site.
Obtain proper rod rotation speed while drilling operation.
Factory settings are as follows:
T45 specification: 140 rpm
T51 specification: 120 rpm
To Hydraulic Schematic Back Front page Next
3: Rod rotation speed adjustment 2/5
1 Put a reflecting sticker on the
shank rod
Required tools:
• reflecting sticker
To Hydraulic Schematic Back Front page Next
3: Rod rotation speed adjustment 3/5
3
Push the normal
rotation switch once
2
Set the rotation mode
in the N mode.
Click
!
To Hydraulic Schematic Back Front page Next
3: Rod rotation speed adjustment 4 Measure rotation speed with 4/5
a rotation gauge by pointing it to
the reflecting sticker
Required tools
• Rotation gauge
* Perform rod rotation speed adjustment under drilling condition
To Hydraulic Schematic Back Front page Next
3: Rod rotation speed adjustment 5/5
5 Loosen the lock dial and
adjust the rod rotation speed
adjustment valve
Clockwise:
speed decrease
Counterclockwise:
speed increase
Factory setting
T45 specification: 140 rpm
T51 specification: 120 rpm
To Hydraulic Schematic Back Front page Next
