USER MANUAL Ver2.

CS-2000
BANKNOTE SORTER

SHINSUNG ELECTRONICS CO., LTD.

-1-
 INTRODUCTION

We thank our customers for choosing products of Shinsung Electronics and hope you thoroughly enjoy
our products. This users’ manual is to help our customers understand various features of this product in a
more convenient way. We strongly recommend you all to read the manual before using the product for
your convenience. All rights with regard to patent, trademark, copyright, and other intellectual properties
are reserved to Shinsung Electronics Co. Ltd. All contents of this manual cannot be illegally copied or
reprinted in any means or form without a prior permission from Shinsung Electronics Co. Ltd. Any attempt
or action to use whole or part of the manual without consent can be punished.

Manufacturers, importers, and selling agencies do not and will not hold any responsibility of accidental
damages or any damage made by inadequate usage and mishandling of this product including injuries
occurred by users.

Information that the users’ manual contains is written based on specification of current products.

The product manufacturer, Shinsung Electronics Co. Ltd., is committed to supplement new features and
will continue to update any new technology application. All standards and specification can be changed
without a prior notice to individual users.

-2-
 SAFTY INSTRUCTION

Please read following instructions carefully to prevent any danger

or property damage in advance. We also notify that product
guarantee can no longer be valid even one of following
instructions is not fulfilled. .

※ Safety procedure

1. Make sure to use an authentic plug for power supply plug.

2. Do not use a damaged plug or loose outlet.

3. Do not plug in many plugs on one outlet.

4. Make sure to unplug when moving the product.

5. Do not bend power supply plug compulsively and be careful not break by placing

a heavy object (It can cause a fire).

6. Do not touch a plug with wet hands (It can cause a fire or electric shock).

7. Do not let any part of your body or uniform touch the device while operating.

8. Do not open the door of the device while operating.

9. Make sure to turn off the power when using upper and lower stacker.

10. Make sure to open after confirming the device is completely stopped and off.

11. Do not spill any beverage on the device.

12. If power switch is damaged, please contact our customer’s service for repair.

※ We will not be responsible for any damage occurred by exchanging parts or repairing from
unauthorized agencies.

-3-
※ Use for long hours

1. Keep this device out of direct sunlight

2. Keep this device out of extremely hot and cold places with no exception to humid and dusty
places.

3. Do not touch or press control keys or LCD Panel with anything pointy such as pin or pen

4. Be careful not to add any metal clip or pin into the device.

5. Device installation place should be firm and stable to the weight of device and secure from
vibration.

※ Important

1. About the inserting paper money

1) Avoid wet or damaged bills

2) Folded bills or even folded in the edge should be unfolded and flattened before insert them.

3) Remove any unnecessary substance on the bill.

4) Any oily stained bill or that covered with chemicals can cause error.

2. When inserting paper money

1) Make sure the bill is arranged and in order (right-left, top-bottom) when you insert.

2) If the bill is not properly arranged when inserting, it can cause error.

3) Do not place your hand or any other substance while operating.

※ Check up for maintenance

1. When you conduct inspection, make sure to turn the power off and unplug.

2. Do not use chemicals for removing stains and cleaning. It can change in quality or color.

3. When using for long hours, make sure to remove dust, stain, or other substances on the
sensor before the operation.

4. Carefully wipe with soft fabrics when cleaning main device.

5. Please contact our customer’s service when the device makes funny sound.

-4-
INTRODUCTION

SAFTY INSTRUCTION

1. EXTERNAL DESIGN AND DESCRIPTION

2. SPECIFICATION

3. FEATURES

4. OPERATION

5. SELF-DIAGNOSTIC

6. FUNCTION(OPERATION MODE)

7. INITIAL SETTING

8. TROUBLESHOOTING

9. RESET(RETURNING TO FACTORY SETTING)

10. FEEDER ADJUSTMENT

11. JAM RECOVERY

APPENDIX 1. IMAGE BOARD PROGRAMMING INSTRUCTIONS

APPENDIX 2. C16XFLASHER INSTRUCTIONS

APPENDIX 3. MACHINE ID, TIME, PASSWORD INPUT

-5-
1. EXTERNAL DESIGN AND DESCRIPTION

Upper Cover
Key Hopper
Display

Side
Cover

Reject
Stacker 1
Stacker 2
ADD Stacker

Dust Collector Fan

-6-
 1-1. CONTROL PANEL

1 2 3 6 1 14
3

4
5

7
1 8 1 91 1 1
1. 0 2
1 Mode (Function)
Function. : To select 5 6
Counting (CNT) – Mixed Denomination Sorting (MDC) – Face and Back Sorting (FAC) – Orientation
Sorting (ORT) – Fitness Sorting (FIT)

2. Kind : To select Sing denomination (FDC) or Mixed denomination (MIX) processing

3. CF/Rej. Table : To display details of rejected notes

4. Fit A : To select Fit A mode

5. Fit B : To select Fit B mode

6. ADD : To accumulate the notes including the quantity in pocket which is not full.

7. Fit C : To select Fit C mode

8. O/N : To select Old / New / Old&New

9. ADD/Value C : To clear the Number and Value of processed banknotes with ADD function.

10. * : To enter Setting mode by combination with other keys.

11. Print: To print the result of processed banknotes

12. Value/Del. Table : To display Number and Value of each denomination.

13: LCD Display : To show current operation of machine

14. Number Key: To enter the number of note to complete the batch.

15. Clear key : To clear the Number and Value of processed notes.

16. Start / Stop : Start or Stop while machine operation

*** Direction Key used in Setting Mode

Movement of “Page” Movement of “Cursor”

O/N

-7-
2. SPECIFICATION

1) Structure : Extendable Stacker Type Banknote Sorter

2) Speed : Approx 760 ~ 800 notes/Min.

3) Recognition : Full Scanning Technology with high speed CIS

4) Hopper Capacity : Approx. 700notes

5) Stacker Capacity:

REJECT : Approx. 200notes

STACKER : 200notes

6) Affordable Banknote Spec.

Size : 50x100 ~ 90x185(mm)

Thickness : 0.06 ~ 0.12(mm)

7) LCD Display : 3.2inch TFT-LCD

8) Device Size and Weight

Main Unit [Standard (3Pocket; 1 Reject +2 Pockets)]

Size : 620 x 344 x 350(mm)

Weight : 45Kg

Additional Stacker

Size: 180 x 344 x 270(mm)

Weight : 7Kg

9) Power : AC100 ~ 240V[50Hz/60hZ] / 200W

10) Storage Temperature : -20 ~ +40

11) Operating Temperature : -15 ~ +30

12) Affordable Humidity 50% ~ 85%RH

-8-
3. FEATURES

1) Fitness Sorting (FIT)

CS-2000 sorts banknotes based on their quality (fitness) with user-friendly setting.

User can set Denomination, Direction, Batch, and Mode for each pocket.

2) Counting (CNT)

Set the denomination and count.

3) Denomination Sorting (MDC)

CS-2000 sorts banknotes based on denomination.

4) Counterfeit (CF)

CS-2000 detects counterfeit and sort it to Reject or Reject 2(CF) pocket.

5) Face up down (FAC)

CS-2000 detects and sort face and back of the notes

6) Orientation (ORT)

CS-2000 does orientation of bills

7) Totaling (ADD)

CS-2000 does total the amount and number of processed banknote

8) Orientation (F&O : Over 5Pockets Sorter)

CS-2000 is capable of one time procedure for the orientation of banknotes

9) Value Adjustment for Fitness Sorting

CS-2000 provides user-friendly Fitness value adjustment feature with simple key operation
such as soil level, tear and hole …etc.

-9-
10) Self-Diagnostic

CS-2000 does take self diagnosis and display error messages when it is turned on.

11) Interface (External Port)

2 Serial Port(RS-232C) : PC & Printer Connection

2 USB Port : PC

-10-
4. OPERATION

CS-2000 runs in AC100 ~ 240V[50Hz/60Hz]. When it is turned on, Display shows “LOADING”
message with processing bar. It takes about 8 sec. and runs the motors when it finishes self-
diagnostic procedure (Sensors Checking).

When it is ready for normal operation, display shows as follows.

FUNCTION KIND BATCH

CNT MIX 100

IDR O& OR
N T
Currency 0 Amount of notes
0
Quantity of notes

Version of
Currency –
Old/New When Orientation
Detection in On

-11-
5. SELF DIAGNOSTIC
CS-2000 does take self-diagnostic and display error messages while its booting. During its
operation, CS-2000 also can show the error messages detailed in following table and
light on jam indicator LED in case of paper jam or sensor Error defect.

1) In case, its upper cover is open or dust on sensors, the display shows following messages

Error Message Jam & Sensor Location

Counter Left Counter Left Sensor

Counter Right Counter Right Sensor

CIS1 Left CIS Left Start Point Sensor 1

CIS1 Right CIS Right Start Point Sensor 1

CIS2 Left CIS Left Start Point Sensor 2

CIS2 Right CIS Right Start Point Sensor 2

MT Left Metal Thread Left Sensor

MT Right Metal Thread Right Sensor

MG Left Magnetic Sensor Start Point Left Sensor

MG Right Magnetic Sensor Start Point Left Sensor

UV UV Sensor

TH Left Thickness Sensor Start Point Left Sensor

TH Right Thickness Sensor Start Point Right Sensor

US Left Ultrasonic Sensor Left

US Right Ultrasonic Sensor Right

-12-
2) In case side cover is open or it found something on side cover like jam or dust.

Error Message
Jam & Sensor Location

Swing0 Left Swing0 Selector Left Start Point Sensor

Swing0 Right Swing0 Selector Right Start Point Sensor

3) In case stacker is open or it found something on stacker like jam or dust.

Error Message
Jam & Sensor Location

Swing1 Swing1 Selector Start Point Sensor

Swing2 Swing2 Selector Start Point Sensor

Swing3 Swing3 Selector Start Point Sensor

Stacker0 count Stacker 0 Count Sensor (Reject Pocket)

Stacker1 count Stacker 1 Count Sensor

Stacker2 count Stacker 2 Count Sensor

Stacker0 rep Stacker 0 Detector Sensor (Reject Pocker)

Stacker1 rep Stacker 1 Detector Sensor

Stacker2 rep Stacker 2 Detector Sensor

Stacker3 rep Stacker 3 Detector Sensor (Add Stacker)

Counter Left 3 Add Stacker Count Left Sensor

Counter Right 3 Add Stacker Count Right Sensor

Stacker Left 3 Stacker 3 Left Count Sensor (Add Stacker)

Stacker Right 3 Stacker 3 Right Count Sensor (Add Stacker)

Door open Stacker0, 1, 2 Door Detector Sensor

Door open 3 Add Stacker Door Detector Sensor

-13-
4) In case hopper is open or it found something on stacker like jam or dust.

Error Message Related Sensor

Hopper Hopper Sensor

5) In case of communication Error between Main controller and Image processing controller.

Error Message CAUSE

IRIS Board1 err IRIS Board1 or CIS(#1 CIS Part)

IRIS Board2 err IRIS Board2 or CIS(#2 CIS Part)

IRIS Board Error IRIS Board1 & IRIS Board2

6) Sensor Layout.

-14-
 6. FUNCTION(OPERATION MODE)

1) FIT (Fitness Sorting Mode) : REJECT/ FIT / UFIT/ATM Sorting based on quality of
banknote.

FIT A -.> Operator can process Single denomination Fitness sorting or Mixed
denomination Fitness Sorting.

FIT B , FIT C -> Operator can set the Denomination and Batch of each pocket.

*** CS-2000 can save the different settings of FIT A, FIT B, FIT C

FIT A setting

(1) Select “FIT” mode with “Function Key” and press “Fit A Key”

(2) Set Single denomination (FDC) or Mixed denomination (MIX) with “Kind Key”

(3) Set the Direction and Mode for each pocket in FIT A MODE SET with “ *key +Fit A key”.

*** Setting value is changed with “ADD/Value C key”

*** After setting, press “Start Key” to return back to operation display.
FUNCTION KIND BATCH FIT_A MODE SET IDR
*** All changed setting values are saved automatically.
P1 NO OLD UFIT
FIT MIX 100 P2 OLD FIT
P3 NO OLD ATM
0 P4
P5
NO
NO
OLD
OLD
UFIT
FIT
NO
0 P6
P7
P8
NO
NO
OLD
OLD
OLD
ATM
UFIT
FIT
P9 NO OLD ATM
P10 NO OLD UFIT
P11 NO OLD FIT
NO
<Orientation of Note> <Currenty type – Old&New> <Pocket mode>
NO - All denomination OLD – Old version of IDR CF - Suspected notes
FT - Face up & Top side feeding New – New version of IDR UFIT - Unfit condition notes
RT - Rear & Top side feeding O&N – Old and New together FIT – Fit condition notes
FB - Face up & Bottom side feeding * This setting will be ignored ATM – ATM condition notes
RB - Rear & Bottom side feeding “when Orientation Detection
Fa - Face up is On”
Re - Rear
Ri - Right
Le – Left
* This setting will be ignored
“when Orientation Detection is On”

-15-
 FIT B & FIT C setting

(1) Select “FIT” mode with “Function Key” and press “Fit B Key”

(2) Set the Direction, Batch, and Mode for each pocket in FIT B MODE SET with “ *key +Fit
B key”.

(3) Move to the next screen with “Print Key” And, set the Denomination for each pocket with
“Number Key”
1 - 1k, 2 – 2k, 3 – 5k, 4 – 10k, 5 – 20k, 6 - 50k, 7 – 100k
(To remove it, Press the number again.)
(4) Set FIT C with same procedure.

*** Setting value is changed with “ADD/Value C key”

*** After setting, press “Start Key” to return back to operation display.

*** All changed setting values are saved automatically.

FIT_B MODE SET IDR P1: 1k 2k 5k 10k

P1 NO OLD 100 UFIT 20k 50k 100k
P2 OLD 100 FIT P2: 1k 2k 5k 10k
P3 NO OLD 100 ATM 20k 50k 100k
P4 NO OLD 100 UFIT
P3: 1k 2k 5k 10k
P5 NO OLD 100 FIT
P6 NO OLD 100 ATM 20k 50k 100k
P7 NO OLD 100 UFIT P4: 1k 2k 5k 10k
P8 NO OLD 100 FIT 20k 50k 100k
P9 NO OLD 100 ATM P5: 1k 2k 5k 10k
P10 NO OLD 100 UFIT
P11 NO OLD 100 FIT 20k 50k 100k
NO
<Direction of Note> <Currenty type – Old&New> <Pocket mode>
NO - All denomination OLD – Old version of IDR CF - Suspected notes
FT - Face up & Top side feeding New – New version of IDR UFIT - Unfit condition notes
RT - Rear & Top side feeding O&N – Old and New together FIT – Fit condition notes
FB - Face up & Bottom side feeding ATM – ATM condition notes
RB - Rear & Bottom side feeding
Fa - Face up <Batch for each pocket>
Re - Rear Setting the number of
Ri - Right notes to be in each pocket
Le - Left

-16-
2) CNT (Counting Mode) : Simple Counting Mode

(1) Select “CNT” mode with “Func. Key”

(2) Set Single denomination (FDC), Mixed denomination (MIX), or FREE with “Kind Key”

*** FREE operation can be selected in only CNT mode.

The machine does not detect any feature of notes in FREE. So, any other currencies
can be counted in FREE operation.

FUNCTION KIND BATCH

CNT MIX 100

0
0

3) MDC (Mixed Denomination Sorting) : In this mode, CS-2000 sorts out Mixed denomination Notes by
denomination.

(1) Select “MDC” mode with “Func. Key”

(2) Select the processing method with “Kind key”

i) CASE1 : Each pocket is filled with one denomination by feeding order.

ii) CASE2 : Each pocket is filled with one denomination, but the Last pocket is reserved for all
remaining denomination.

iii) CASE3 : The machine process the notes by MDC Setting ( *key + O/N key)

FUNCTION KIND BATCH

MDC CASE1 100

0
0

-17-
 *** In CASE3 of MDC mode,

Operator can set denomination and direction for each pocket with “ *key + O/N key”

MDC MODE SET IDR P1: 1k 2k 5k 10k

P1 NO OLD 20k 50k 100k
P2 OLD P2: 1k 2k 5k 10k
P3 NO OLD 20k 50k 100k
P4 NO OLD
P3: 1k 2k 5k 10k
P5 NO OLD
P6 NO OLD 20k 50k 100k
P7 NO OLD P4: 1k 2k 5k 10k
P8 NO OLD 20k 50k 100k
P9 NO OLD P5: 1k 2k 5k 10k
P10 NO OLD
P11 NO OLD 20k 50k 100k
NO
<Direction of Note> <Currenty type – Old&New>
NO - All denomination OLD – Old version of IDR
FT - Face up & Top side feeding New – New version of IDR
RT - Rear & Top side feeding O&N – Old and New together
FB - Face up & Bottom side feeding
RB - Rear & Bottom side feeding
Fa - Face up
Re - Rear
Ri - Right
Le - Left

-18-
4) FAC (Face & Back) : With this mode, CS-2000 sorts the banknote by face and back of
banknote.

(1) Select “FAC” mode with “Func. Key”

(2) Set Single denomination (FDC) or Mixed denomination (MIX) with “Kind Key”

FUNCTION KIND BATCH

FAC MIX 100

0
0

5) ORT (Orientation) : With this mode, CS-2000 sorts the banknote by direction of
banknote.

(1) Select “ORT” mode with “Func. Key”

(2) Set Single denomination (FDC) or Mixed denomination (MIX) with “Kind Key”

FUNCTION KIND BATCH

ORT MIX 100

0
0

-19-
6) F&O (Face & Orientation) : In this mode, CS-2000 sorts the banknotes by direction and
face / back of banknotes in one step.

*** This mode can be run only with more than 5pocket sorter(1 Reject and 4 Pockets)

(1) Select “F&O” mode with “Func. Key”

(2) Set Single denomination (FDC) or Mixed denomination (MIX) with “Kind Key”

FUNCTION KIND BATCH

F&O MIX 100

0
0

7) ADD : With “ADD” feature, CS-2000 shows total number of banknote being processed.

*** ADD feature can be combined with other modes.

FUNCTION KIND BATCH

CNT MIX 100

0
ADD 0

-20-
8) Orientation (Direction) Detection : In this mode, CS-2000 detect different direction of
notes based on first fed note.

*** This mode can be combined with CNT and Fit A mode.

(1) Set Orientation “On” in Service setting( *key+Function key)

FUNCTION KIND BATCH

F&O MIX 100

IDR O& OR
N T
0
0

9) BATCH
Operator can set the number of note to be in each pocket Stacker) with number keys
(20/50/100/150/200).

-21-
10) Reject Detail

CS-2000 shows details of rejected notes with “CF/Rej. Table Key”

REJECT TABLE
Diff. Denom 0
D ID Error 0
I Suspect (IR) 0
U Suspect (UV) 0
M Suspect (MG) 0
d Double 0
G Feeding Err 0
T Taped 0
H Hole / Corner 0

11) Result for each denomination

CS-2000 shows Quantity and Amount for each denomination with “Value/Del. Table Key”

VALUE TABLE

1k 0 0
2k 0 0
5k 0 0
10k 0 0
20k 0 0
50k 0 0
100k 0 0

-22-
7. INITIAL SETTING

7-1. USER SETTING 1

1) CS-2000 allows to check and change some of settings with simple key operation if necessary
2) Press “ * Key + Kind Key” together to enter in User Setting mode for basic setting and find
following screen from Display. (Press “Print Key” to move next screen / “Kind Key” for
reverse order)
3) To change setting value, use “ADD/Value C key” or “Number key”

CURRENCY
LOCAL CURRENCY IDR

-. Selecting Currency

FUNCTION ON/OFF
PRINT off
ERROR DISPLAY on -. Selecting On/Off of Basic
ALARM on functions and operation modes
AUTO / MANUAL Auto
CNT MODE on
MDC MODE on
FAC MODE on
ORT MODE on
F&O MODE on
FIT MODE on

*** All changed setting values are saved automatically.

-23-
7-2. USER SETTING 2 (PRINT SET)

To Print out the report of work, User should preset followings.

* Baud-rate of printer should be set to 19200

1) Press “ * Key + Print Key” to enter and set the print format.

(Press “Print Key” to move next screen / “Kind Key” for reverse order)

TIME SETTING

DATE: 30_05_2011
TIME: 00:00:00
-. Time checking

ID SETTING

CLIENT ID: AA0000

USER ID: AA0000
-. Entering Operator’s information
DEVICE ID: 0000
and deposit amount
DEPOSIT AMOUNT
0.00

REJECT NUMBER
1k IDR 0
2k IDR 0
-. Entering the number of Rejected
5k IDR 0
10k IDR 0 notes
20k IDR 0
50k IDR 0
100k IDR 0

CF NUMBER
1k IDR 0
2k IDR 0
5k IDR 0 -. Entering the number of suspected
10k IDR 0 notes and coins
20k IDR 0
50k IDR 0
100k IDR 0
DEPOSIT COINS
0.00

-24-
 8. TROUBLESHOOTING

8-1. ERROR CODE IN OPERATION

No. ERROR CODE CAUSE TROUBLESHOOTING

① Unrecognizable note or ①Check the note with “D” Error in Reject Stacker and
“D”
1 fail to recognize owing to find if it is reasonable reject or not.
skew feeding…etc. ②Check the Size of note

①Counterfeit
“U” ①Counterfeit Detection
2 ②Normal note but different
②Check UV Value if necessary
UV level

①Double Fed note or

①Check the thickness of note and thickness sensor
Thicker note than normal
value and voltage if necessary
note
“T”
3
①Taped note or Thicker
①Check if it is taped note
note than normal note

①Check if it is double feeding

“d” ②Check Ultra sonic sensors and clean them
4 ①Double feeding
③Check the Ultra sonic sensor value and correct
them if necessary

“G” ①Check the gab between feeding rollers and adjust

5 Unstable Feeding
them if necessary

Check the note with “I” Error in reject pocket.

①Counterfeit note
②If many of genuine notes go to reject with “I” error
“I”
6 ① Counterfeit Note then, check image controller and calibrate them and
②Too Dark download S/W or replace the board again if
necessary.
③Check if there is dust on CIS

①Check if there is hole or missing corner on the note

7 “H” ① Hole or Missing Corner
②Check Hole/Tear/Corner value if necessary

① Counterfeit
“M” ①Counterfeit Detection
8 ② Normal note but different
②Check MG Value if necessary
MG level

-25-
9. RESET (RETURNING TO FACTORY SETTING)

1. In case, it is needed to return all values to be factory set, press “ * Key and Clear Key”
together and check “Buzzer” sound and turn OFF and ON the device twice.

2. Then, you will find all value turns to initial Factory setting value.

*** RESET should be done after checking with service person.

-26-
 10. FEEDER ADJUSTMENT
When “d”, “G” error occurs frequently during operation, it may need “Feeder Adjustment”.

Unstable note feeding may cause high reject owing to double feeding, feed error, often jamming,
skew feeding and recognition failure.

1) “d” Error (double Detection Error)

If gap between feeding rollers is wider, it often causes double feeding. In this case, turn the adjustment
knob(screw) count clockwise slightly and see the result.

ex) If it is, now, in position of “0”, turn it to” –1” . If it is turned too much, feeder may not feed the note
properly

2) “G” Error (Gap Error)

If gap between feeding rollers is wider or narrower, it also causes “G” Error. In this case, adjust the
knob(screw) correctly and see the result. (mostly in case, gap between feeding rollers is wider, it cause
“G” error as well)

Gap means distance between notes (for example. 1st fed note and 2nd fed note)

ex) If it is, now, in position of “0”, turn it to” –1” . If it is turned too much, feeder may not feed the note

Adjustment
Knob(Screw)

-27-
 11. JAM RECOVERY
1) When Jamming occurs during the operation, find error message on display (Stacker and Main) and
location of jamming.

2) Open the doors and covers like following picture and remove the jam.

3) While removing the jam, the operator should be careful not to damage any sensor or belt on the track.

4) If it gives error continuously after removing jam, check it again carefully if there is any piece of notes in
the track and make sure all the sensors are working properly.

-28-
SEOUL OFFICE :

#1003 WORLD MERIDIAN II, 426-5, GASAN-DONG, GEUMCHEON-KU, SEOUL,

KOREA.

TEL : +82 2-2025-4120 FAX : +82 2-2025-4123

FACTORY :

TEL : +82 55-337-3030 FAX : +82 55-337-3033

-29-