Non-destructive Testing

Definition of NDT (NDE)

The use of noninvasive
techniques to determine
the integrity of a material,
component or structure
or
quantitatively measure
some characteristic of
an object.

i.e. Inspect or measure without doing harm.

 What are Some Uses
of NDE Methods?

• Flaw Detection and Evaluation

• Leak Detection
• Location Determination
• Dimensional Measurements Fluorescent penetrant indication

• Structure and Microstructure Characterization

• Estimation of Mechanical and Physical Properties
• Stress (Strain) and Dynamic Response Measurements
• Material Sorting and Chemical Composition
Determination
 Why Nondestructive?
• Test piece too precious to be destroyed
• Test piece to be reuse after inspection
• Test piece is in service
• For quality control purpose
• Something you simply cannot do harm
to, e.g. fetus in mother’s uterus
 Major types of NDT
• Detection of surface flaws
 Visual
 Magnetic Particle Inspection
 Fluorescent Dye Penetrant Inspection
• Detection of internal flaws
 Radiography
 Ultrasonic Testing
 Eddy current Testing
1. Visual Inspection
Most basic and common
inspection method.

Tools include
fiberscopes,
borescopes, magnifying
glasses and mirrors.

Portable video inspection

unit with zoom allows
inspection of large tanks
and vessels, railroad tank
cars, sewer lines.
Robotic crawlers permit
observation in hazardous
or tight areas, such as air
ducts, reactors, pipelines.
 2. Magnetic Particle Inspection (MPI)
2.1 Introduction

• A nondestructive testing method used for

defect detection. Fast and relatively easy to
apply and part surface preparation is not as
critical as for some other NDT methods. MPI
one of the most widely utilized
nondestructive testing methods.
If iron particles are sprinkled on a cracked magnet, the particles will
be attracted to and cluster not only at the poles at the ends of the
magnet but also at the poles at the edges of the crack. This cluster
of particles is much easier to see than the actual crack and this is
the basis for magnetic particle inspection.
 Magnetic Particle Inspection
• The magnetic flux line close to the surface of a
ferromagnetic material tends to follow the surface
profile of the material
• Discontinuities (cracks or voids) of the material
perpendicular to the flux lines cause fringing of
the magnetic flux lines, i.e. flux leakage
• The leakage field can attract other ferromagnetic
particles
The magnetic particles form a
ridge many times wider than
the crack itself, thus making
the otherwise invisible crack
visible

Cracks just below the

surface can also be
revealed
 2.4 Advantages of MPI
• One of the most dependable and sensitive methods
for surface defects
• fast, simple and inexpensive
• direct, visible indication on surface
• unaffected by possible deposits, e.g. oil, grease or
other metals chips, in the cracks
• can be used on painted objects
• surface preparation not required
• results readily documented with photo or tape
impression
 2.5 Limitations of MPI
• Only good for ferromagnetic materials
• sub-surface defects will not always be indicated
• relative direction between the magnetic field and the
defect line is important
• objects must be demagnetized before and after the
examination
• the current magnetization may cause burn scars on
the item examined
Examples of visible dry magnetic particle indications

Indication of a crack in a saw blade Indication of cracks in a weldment

Indication of cracks running between

Before and after inspection pictures of attachment holes in a hinge
cracks emanating from a hole
 3. Dye Penetrant Inspection
Liquid penetrant inspection (LPI) is one of the
most widely used nondestructive evaluation
(NDE) methods. Its popularity can be attributed
to two main factors, which are its relative ease
of use and its flexibility. LPI can be used to
inspect almost any material provided that its
surface is not extremely rough or porous.
Materials that are commonly inspected using
LPI include metals (aluminum, copper, steel,
titanium, etc.), glass, many ceramic materials,
rubber, and plastics.
 Why Liquid Penetrant Inspection?
• To improves the detectability of flaws
There are basically two ways that a
penetrant inspection process
makes flaws more easily seen.
(1) LPI produces a flaw indication
that is much larger and easier for
the eye to detect than the flaw
itself.
(2) LPI produces a flaw indication
The advantage that a liquid with a high level of contrast
penetrant inspection (LPI) offers between the indication and the
over an unaided visual inspection is background.
that it makes defects easier to see
for the inspector.
 3.4 Primary Advantages
• The method has high sensitive to small surface discontinuities.
• The method has few material limitations, i.e. metallic and
nonmetallic, magnetic and nonmagnetic, and conductive and
nonconductive materials may be inspected.
• Large areas and large volumes of parts/materials can be inspected
rapidly and at low cost.
• Parts with complex geometric shapes are routinely inspected.
• Indications are produced directly on the surface of the part and
constitute a visual representation of the flaw.
• Aerosol spray cans make penetrant materials very portable.
• Penetrant materials and associated equipment are relatively
inexpensive.
 3.5 Primary Disadvantages
• Only surface breaking defects can be detected.
• Only materials with a relative nonporous surface can be inspected.
• Precleaning is critical as contaminants can mask defects.
• Metal smearing from machining, grinding, and grit or vapor
blasting must be removed prior to LPI.
• The inspector must have direct access to the surface being
inspected.
• Surface finish and roughness can affect inspection sensitivity.
• Multiple process operations must be performed and controlled.
• Post cleaning of acceptable parts or materials is required.
• Chemical handling and proper disposal is required.
 4. Radiography
Radiography involves the use of penetrating gamma- or
X-radiation to examine material's and product's defects
and internal features. An X-ray machine or radioactive High Electrical Potential
isotope is used as a source of radiation. Radiation is
directed through a part and onto film or other media.
The resulting shadowgraph shows the internal features
Electrons
and soundness of the part. Material thickness and
density changes are indicated as lighter or darker areas + -
on the film. The darker areas in the radiograph below
represent internal voids in the component.
X-ray Generator or
Radioactive Source
Creates Radiation

Radiation
Penetrate
the Sample

Exposure Recording Device

 4.2 Film Radiography
The part is placed between the
radiation source and a piece of film.
The part will stop some of the
radiation. Thicker and more dense
area will stop more of the radiation.
• The film darkness (density) will
vary with the amount of radiation
reaching the film through the
X-ray film test object.
• Defects, such as voids, cracks,
inclusions, etc., can be
detected.
= less exposure
= more exposure
Top view of developed film
 4.3 Areas of Application
• Can be used in any situation when one wishes to view
the interior of an object
• To check for internal faults and construction defects, e.g.
faulty welding
• To ‘see’ through what is inside an object
• To perform measurements of size, e.g. thickness
measurements of pipes

Standard:
ASTM
– ASTM E94-84a Radiographic Testing
– ASTM E1032-85 Radiographic Examination of Weldments
– ASTM E1030-84 Radiographic Testing of Metallic Castings
4.4 Limitations of Radiography
• There is an upper limit of thickness through
which the radiation can penetrate, e.g. -ray
from Co-60 can penetrate up to 150mm of steel
• The operator must have access to both sides of
an object
• Highly skilled operator is required because of
the potential health hazard of the energetic
radiations
• Relative expensive equipment
 4.5 Examples of radiographs

Cracking can be detected in a radiograph only the crack is

propagating in a direction that produced a change in thickness that
is parallel to the x-ray beam. Cracks will appear as jagged and
often very faint irregular lines. Cracks can sometimes appearing as
"tails" on inclusions or porosity.
Burn through (icicles) results when too much heat causes
excessive weld metal to penetrate the weld zone. Lumps of
metal sag through the weld creating a thick globular condition
on the back of the weld. On a radiograph, burn through
appears as dark spots surrounded by light globular areas.
Gas porosity or blow holes Sand inclusions and dross
are caused by accumulated are nonmetallic oxides,
gas or air which is trapped by appearing on the radiograph
the metal. These as irregular, dark blotches.
discontinuities are usually
smooth-walled rounded
cavities of a spherical,
elongated or flattened shape.
 5. Ultrasonic Testing
5.1 Introduction
In ultrasonic testing, high-frequency sound
waves are transmitted into a material to
detect imperfections or to locate changes
in material properties.
The most commonly used
ultrasonic testing technique is
pulse echo, whereby sound is
introduced into a test object and
reflections (echoes) from internal
imperfections or the part's
geometrical surfaces are returned
to a receiver. The time interval
between the transmission and
reception of pulses give clues to
the internal structure of the
material.
 Ultrasonic Inspection (Pulse-Echo)
High frequency sound waves are introduced into a
material and they are reflected back from surfaces or
flaws.
Reflected sound energy is displayed versus time, and
inspector can visualize a cross section of the specimen
f
showing the depth of features that reflect sound.

initial
pulse

back surface
echo
crack
echo

crack

0 2 4 6 8 10 plate

Oscilloscope, or flaw
detector screen
 6. Eddy Current Testing
Electrical currents are generated in a conductive material by an
induced alternating magnetic field. The electrical currents are
called eddy currents because the flow in circles at and just
below the surface of the material. Interruptions in the flow of
eddy currents, caused by imperfections, dimensional changes,
or changes in the material's conductive and permeability
properties, can be detected with the proper equipment.
• Eddy current testing can be used on all electrically conducting
materials with a reasonably smooth surface.
• The test equipment consists of a generator (AC power supply), a
test coil and recording equipment, e.g. a galvanometer or an
oscilloscope
• Used for crack detection, material thickness measurement
(corrosion detection), sorting materials, coating thickness
measurement, metal detection, etc.
 6.2 Eddy Current Instruments
Voltmeter
Coil's
Coil magnetic field

Eddy current's
magnetic field
Eddy
currents

Conductive
material
 6.4 Applications
•Crack Detection
•Material Thickness
Measurements
•Coating Thickness
Measurements
•Conductivity Measurements For:
•Material Identification
•Heat Damage Detection
•Case Depth Determination
•Heat Treatment Monitoring
 6.5 Advantages of ET
•Sensitive to small cracks and other defects
•Detects surface and near surface defects
•Inspection gives immediate results
•Equipment is very portable
•Method can be used for much more than flaw detection
•Minimum part preparation is required
•Test probe does not need to contact the part
•Inspects complex shapes and sizes of conductive
materials
 Limitations of ET
•Only conductive materials can be inspected
•Surface must be accessible to the probe
•Skill and training required is more extensive than other
techniques
•Surface finish and and roughness may interfere
•Reference standards needed for setup
•Depth of penetration is limited
•Flaws such as delaminations that lie parallel to the
probe coil winding and probe scan direction are
undetectable
 Wire Rope Inspection
Electromagnetic devices
and visual inspections are
used to find broken wires
and other damage to the
wire rope that is used in
chairlifts, cranes and other
lifting devices.
 Aircraft Inspection
• Nondestructive testing is used
extensively during the
manufacturing of aircraft.
• NDT is also used to find cracks
and corrosion damage during
operation of the aircraft.
• A fatigue crack that started at
the site of a lightning strike is
shown below.
 Jet Engine Inspection
• Aircraft engines are overhauled
after being in service for a period
of time.
• They are completely disassembled,
cleaned, inspected and then
reassembled.
• Fluorescent penetrant inspection
is used to check many of the parts
for cracking.
 Pressure Vessel Inspection
The failure of a pressure vessel
can result in the rapid release of
a large amount of energy. To
protect against this dangerous
event, the tanks are inspected
using radiography and
ultrasonic testing.
 Rail Inspection
Special cars are used to
inspect thousands of miles
of rail to find cracks that
could lead to a derailment.
 Special Measurements
Boeing employees in Philadelphia were given the privilege of
evaluating the Liberty Bell for damage using NDT techniques.
Eddy current methods were used to measure the electrical
conductivity of the Bell's bronze casing at a various points to
evaluate its uniformity.