Zero point energy conversion for selfsustained generation

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
ARPN Journal of Engineering and Applied Sciences
©2006-2015 Asian Research Publishing Network (ARPN). All rights reserved.
www.arpnjournals.com
4326
ZERO POINT ENERGY CONVERSION FOR SELF-SUSTAINED
GENERATION
P. RajaRajeswari, S. Sakthi, K. Bharathi, M. Sasikumar, and S. Srinivasan
Department of Electrical and Electronics Engineering, Jeppiaar Engineering College, Anna University, Chennai, Tamilnadu, India
E-Mail: praji81@yahoo.co.in
ABSTRACT
In this paper zero point energy conversion is proposed for self-sustained generator applications. Our entire
universe balance is based on a magnetic energy lying in a minimum energy point called zero-point. By using an energy
conversion machine magneto-gravitic link can be made zero-point energy by taking kinetic energy form i.e. rotational
motion .Kinetic energy link is constructed using a special permanent magnet arrangement and it is independent of
electricity . It uses perpetual motion and the kinetic energy is later converted by using a special type low speed axial flux
alternator, comprising two rotating discs in-between which the coil is placed from which the power is drawn .
Keywords: zero point energy conversion (ZPEC), zero point energy (ZPE), magneto-graviticlink(MGL), axial fluxgenerator(AFG),
finite element analysis(FEA), MATLAB.
INTRODUCTION
Electric energy generation is a process involving
choosing perfect fuel source, deriving potential or kinetic
energy converting it to electrical means by using complex
energy conversion mechanism. This needs a power plant
which involves high initial, operating, and maintenance
cost. Though the method is proven to be sufficient in
present situation, in future a replacement or additional
source is posing mandatory. There comes the thought of
how about getting free energy. Free energy idea may
appear to be theoretical, but it’s possible when the zero-
point energy is used efficiently. The idea first took root
from a German scientist Karl Schapeller (1875-1947). In
1930 he developed a device based on this free energy
concept called Karl Schapeller Device, for generating
electrical energy based on the Aethor Theory. From then
on many scientists turned their concentration on this field
of zero-point energy or perpetual motion. In recent
scientist have used rare earth magnets to make permanent
magnet generator, called perendev generator which runs
on the basis of perpetual motion.
ZERO POINT ENERGY
Space is full of gravitons. Gravitons interact with
each other and convert to color charges. Interaction
between gravitons depends on their density in a given
volume. Some gravitons with the same mass CPH convert
to colour-charges and two electric fields form. These fields
neutralize each other. However, positive color-charges
repel each other, and the same action applies to the
negative color-charges.
Therefore, when the intensity of color-charges
grows, about each field (negative and positive fields) a
magnetic field forms. This magnetic field maintains the
electric field.
Magneto -Gravitic link
The meaning of magneto-gravitic link (MGL)
operational principle is in alternate usage in closed cycle
of gravitation force and magnetic forces of repelling
attraction of PM and repeated alternation of gravitation
force which acts on the rotor magnets when shielding the
PM magnetic field by blinds-screens of permanent
magnets magnetic fields where forces of PM magnetic
repelling act on magnetic motor (MM) rotor when such
magnetic shield between PM is absent. These are the
magneto-gravitic links (MGL).
Figure-1. MGL block diagram.
This block diagram clearly shows the ZPEC
using MGL, in a flow.12v D.C. running the pick-up motor,
(coupled with the pick-up pole) which helps in bringing
the rotor in synchronous operation.
Axial-flux permanent magnet generator
Axial flux machines are characterized by an
axially directed air gap flux. Axial flux permanent magnet
generated is formed by a rotor disc carrying magnets that
produce an axial flux [8] and a stator disc containing the
phase windings, single-sided, double-sided, torus, and
multi-disc designs.
PROPOSED CLOSED LOOP
The block diagram of the proposed closed loop
system is shown in Figure-2.
Plan: 1. Ultimate Energizer 2. Pulse-Charging Battery Systems

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4327
Figure-2. MGL block diagram.
The ZPEC is done using MGL as the main
operational element. The air flow energy (ZPE) when
enters the MGL, a magnetic oscillatory field is created.
When the pick-up motor is started by the pick-up motor
battery, this oscillatory motion is transformed into
rotational energy by MGL.
The shaft coupling of the alternator and MGL
results in motion of the alternator. The voltage delivered
by the alternator is stepped-up by the potential transformer
and which drives the load. Part of the alternator voltage is
rectified by rectifier and fed into the voltage regulator
circuit for regulated voltage. This voltage is supplied to
the pick-up motor via controlled relay circuit for operating
the procedure in closed loop.
Modelling of MGL and AFG
The magneto-gravitic link (MGL) operational
principle is in alternate usage in closed cycle of gravitation
force and magnetic forces of repelling attraction of PM
and repeated alternation of gravitation force which acts on
the rotor magnets when shielding the PM [1] magnetic
field by blinds-screens of permanent magnets magnetic
fields where forces of PM magnetic repelling act on
magnetic motor (MM) rotor when such magnetic shield
between PM is absent. Rotor plate is the rotating part of
the MGL. Rotor plate is made of hylam sheet of 4mm
thickness. The sheet is laminated on the rotor surface. This
hylam sheet is a plywood based, having good tensile
strength. The rotor plate is circular in shape with a center
hole of 25mm for the shaft to pass through. The diameter
of the plate is 400mm.The plate sits on the shaft
horizontally as shown in Figure-3. The rotor plate carries
poles on it. The poles are permanent ceramic magnets.
Each magnet is 80mm in diameter with a hole in center
Figure-3. Model of arrangement of magnets in the
MG disc.
There are totally 12 rotor poles. Each rotor pole is
arranged towards the circumference of the rotor plate. The
air-gap distance of 100mm is maintained between each
rotor pole. This is shown in Figure-4. Like A.C.
synchronous motor magnetic locking principle here MGL
is synchronizes. When the pick-up poles implied force on
the rotor pole gets nullified or stabilizes its easier for the
MGL to run without the slip. This means that speed of the
MGL’s rotor and the pick-up getting locked and rotates in
synchronous speed. This shows clearly that MGL works
on ‘magnetic locking’ principle. The overall arrangement
of Magneto-gravitic link with pick-up motor is shown in
Figure-4.
Figure-4.Magneto gravity link arrangement.
The axial flux (disc shape) permanent magnet
machine is an attractive alternative to radial flux
(cylindrical shape) machines in wind turbine applications.
The axial flux configuration is amenable to the low-speed,
high-torque operation of a direct drive wind energy
system. Direct drive wind energy conversion tends to
decrease the system size, weight, and noise, while
increasing overall efficiency and reliability.

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4328
Figure-5.Arrangements of windings of AFG.
We use double sided stator arrangement in this AFG. The
stator plates R1 and R2 are made of hylam sheets each of
250mm in diameter with a center shaft. On the surface the
12 ceramic magnets are placed without air gap as shown in
the Figure. These magnets act as the stator poles.
Here we use a coreless arrangement of the rotor
in order to induce maximum flux induction in between the
plates. Here we use the same hylum sheet for the coreless
solid. The rotor carries the stationary windings. The
windings are Trapezoidal in shape enclosing the ceramic
magnets field. Each coil consists of 300 turns. There are 3
phases R, Y, B are made in this generator. Each arranged
at 120 degrees apart. This can be shown in the following
Figure-5.
CHARACTERISTICS OF MGL
Field strength calculation of permanent magnets in
pick - up pole and rotor
Magnets show repulsion or attraction force
around itself. This area affected from the force of magnets
called magnetic field [8]. Directions of magnetic field
lines are showed below.
Figure-6. Field lines between 2 magnets.
 Never intersect
 If they are parallel we say that there is a regular
magnetic field
Magnetic field is a vector quantity and showed
with the letter B. Unit of B is Tesla. When we calculate
magnetic field of a magnet we assume that there is a 1 unit
of m at the point we want to find. We find the magnetic
field with following formula
B=F/M (1)
We have the following condition prevailing between the
pick-up pole magnet and rotor plate magnets.
Considering k.m/d*d is equal to 5 N/Amp.m the
magnetic field produced by the m1 and m2 at point A.
Here point A means rotor pole and pickup.
Figure-7. Field interaction between rotor and pick-up
pole.
8
2
m
B K
N
d
 8*
2
m
K
d

(2)
7
7* 7*5 35
2 2 .
m m N
B K K
S Amp md d
   
(3)
B B B
A N S
  (4)
Vector addition
2 2 2 240 35 1600 1225B B B
A N S
     
(5)
53.15
.
N
B
A Amp m

(6)
Field force betweenpermanent magnets inpick-up pole
androtor
Effects of the two magnets to each other are
inversely proportional to the square of distance between
them and directly proportional to magnetic pole strengths
of each magnet. These forces are equal in magnitudes and
opposite in directions.F1=-F2
Where; k is the constant, m1 and m2 are the
magnetic intensities of the poles and d is the distance
between them.
8*5 40
.
N
Amp m
 

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4329
Let’s consider the following prevailing
parameters,
Forces exerted by the N poles of the magnets to
each other will be (k=10-7
N.m2
/ (Amp.m) 2
, when the rotor
pole and pick-up pole are placed near.
Figure-8. Force exerted between rotor and pick-up pole.
*
2
2
7 4 310 *10 *10
20.02
112.5*10
m m
F K
d
m

  

 (7)
Two magnets are placed like given picture below.
If the N pole of the magnet exerts F force on the N poles
of the second magnet, find the net force exerted on the
first magnet.
Figure-9. Vector representation of force exerted between
magnets.
MAGNETIC FLUX OF PERMANENTMAGNETS IN
MGL
Magnetic flux is the number of magnetic field
lines passing through a surface placed in a magnetic field.
We show magnetic flux with the Greek letter; Ф. We find
it with following formula
Figure-10. Magnetic flux lines of a permanent magnet.
Ф=B.A.cosӨ (8)
Where Ф is the magnetic flux and unit of Ф is Weber
(Wb)
B is the magnetic field and unit of B is Tesla.
A is the area of the surface and unit of A is m2
.
Figure-11.Magnetic field lines on vertical and horizontal
plane.
In the first one, magnetic field lines are
perpendicular to the surface, thus, since angle between
normal of the surface and magnetic field lines 0 and
cos0=1equation of magnetic flux becomes
Ф=B.A(9)
In the second picture, since the angle between the
normal of the system and magnetic field [8] lines is 90º
and cos90º=0 equation of magnetic flux becomes
Ф=B.A.cos90º=B.A.0=0 (10)
Magnetic permeability of the vacuum is denoted
by;µo and has value ,
µo=4π.10-7
Wb./Amps.m (11)
We find the permeability of the matter by
following formula,
µ= B / H (12)
Relative permeability is the ratio of a specific
medium permeability to the permeability of vacuum,
µr=µ/µo (13)

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4330
ALGORITHM
Starting of AFG for program
Figure-12.Algorithm of AFG starting.
Starting of MGL
Figure-13.Algorithm of AFG starting.
While varying the resistor along the I adjust pin
of LM338, we must note that there is no slip in pick-up
pole of the MGL. If any slip is noticed bring the resistor
value to minimum position, open the push switch. The
pole is because improper loading of the pick-up motor.
Repeat steps from 1 to 5.
Figure-14. Pickup rotating speed vs supply resistance.
Stopping of MGL
Figure-15.Stopping of MGL.
Magnetic Drag Effect
The field passage of ZPE is very sharp in magnet
ends. When relating this to MGL, the field force gets
increased very rapidly leading to fast movement of the
rotor pole to its next position. When magnetic drag
increases or decreases it has an effect on the speed - torque
characteristics.

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4331
Figure-16. Speed vs torque.
Relation between Speed of Pick - Up pole andspeed
ofrotor pole
This is very simple principle of the synchronism
of MGL. Like A.C. synchronous motor magnetic locking
principle here MGL is synchronizes. When the pick-up
poles implied force on the rotor pole gets nullified or
stabilizes its easier for the MGL to run without the slip.
This means that speed of the MGL’s rotor and the pick-up
getting locked and rotates in synchronous speed. This
shows clearly that MGL works on ‘magnetic locking’
principle.
Figure-17. Pick-up motor vs MGL speed.
MAGNETIC FIELD IN AFG ON NO LOAD
The flux density determined by the analytical
method compared with FEA (Field Element Analysis)
results for both the innermost slice (smallest radius) and
outermost slice (largest radius).From the Figure, it is clear
that the analytic result closely matches the FEA
computation [7]. It should also be noted that the flux
density at the outer slice has a more pronounced peak than
the inner radius, since the relative magnet width per pole
pitch varies with radius. This feature is not captured using
the mean radius approach of other analytic solutions.
Figure-18. FEA and analytical air gap flux density
curve (no load).
Magnetic field inAFGunderload
The figure shows peaks near the edge of the
phase band and an average value of .004 Tesla. The
armature reaction field is significantly smaller than the
field produced by the permanent magnets [10]. This is a
characteristic of the slot less, ironless core machine. Since
the average magnitude of the armature reaction is
insignificant compared to the permanent magnet field, it is
reasonable to neglect armature reaction. The graphical
representation of the AFG under loaded condition is as
shown in the following graphical format.
Figure-19.FEA and analytical air gap flux density
curve (on load).
HARDWARE RESULTS AND DISCUSSIONS
To verify the results of the Proposed Zero point
energy conversion, hardware prototype model was
constructed and its picture is shown in the Figure-16.
The IC used in the motor controller in the
hardware prototype is TL494 and the Controller Circuit is
shown in the Figure-16.

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4332
Figure-20. Motor speed controller.
Rotor plate is the rotating part of the MGL.
Figure-21.Magneto-gravitic link design.
Axial flux generator design
Figure-22.Axial flux generator design.
Figure-18 shows the actual construction of axial
flux generator constructed design.
Working model
Figure-23.Hardware prototype.
The hardware model is shown in Figure-19.
EXPERIMENTAL RESULTS
On experimental analysis we found the following
operating parameters in this ZPEC using MGL and AFG.
MGL
Table-1.MGL experimental analysis parameters.
Rpm 350
Force between rotor and pick-up
pole
22.28 N
Torque produced in MGL 4.1202 Nm
AFG
Table-2.AFG experimental analysis parameters.
Rpm 300
Phase to phase voltage 11.7
Phase to neutral 7.6
Current 1
Boosted voltage 110
Magneto gravitic link calculations
Initial input to the pickup motor = 12 v battery
Dimensions of magnet
 Produced by AFG = 0.0125 Tesla
 Mass of magnet = 0
 Inner radius of magnet = 15 mm
 Outer radius of magnet = 35 mm
 Magnetic attraction distance of magnet used = 35 mm
 Reminisce field of magnet = 1.06
 Magnetic flux density = 0.0279 Tesla
 Energy produced = 309.6639 J/m3

VOL. 10, NO. 10, JUNE 2015 ISSN 1819-6608
4333
 Force = 3.4825e+007 N
 Power consumed by one magnet = 5.1611 Watt
 Radius of disc = 0.35 m
 Enter mass of magnet = 0.2 kg
 Torque produced on Shaft by MGL = 4.1202 Nm
 Speed of PICKUP motor used = 2000rpm
 No. of poles = 12
 Speed obtained in the shaft = 166.6667 rpm
Axial flux generator calculations
 Inner radius of magnet = 10 mm
 Outer radius of magnet = 20 mm
 Thickness of magnet = 10 mm
 Magnetic attraction distance of magnet used = 40 mm
 Remenance field of magnet = 1.06
 Magnetic flux density 15 kg
 Radius of disc = 0.18 m
 Minimum Torque required to rotate axial flux
generator = 1.5892 (Nm)
 No. of turns per phase = 300
 Output voltage obtained = 9.4259 V
 Output power obtained from AFG = 26.1211 Watt
 Feedback Output given back to pick-up motor is 24
Watt and the remaining useful power is 2.1211Watt.
The useful power can be increased by increasing
the grade of magnets used and by increasing the gauge of
copper wire used in windings of AFG and also by
increasing the speed of pickup motor used. The main
advantage of this principle is the feedback given to the
pickup motor is constant and independent of load.
CONCLUSIONS
This paper proposes a Zero Point Energy
Conversion which is a closed cycle of electricity
generation and capable of self-sustained with 12 V dc as
initial input thereby finding its applications in domestic
use of generating electricity. The Hardware Description
was discussed in the paper for closed cycle of electricity
production. This conversion of free vacuum energy into
electrical energy opens gate to a new era of energy
conversion. The ZPEC has not only emerged in electrical
energy production, additionally this given us the key of
self-sustenance in energy conversion. At present the ZPEC
will be the best solution to replace the depleting fossil
fuels this kind energy conversion mechanism will lead to
the clean and green energy. In future if these kinds of
energy conversion solutions are considered then we can
rest assured high energy output at less complexity.
REFERENCES
[1] Garrison F. Price, Todd D. Batzel, MihaiComanescu
and Bruce A. Muller. 2008. Design and Testing of a
Permanent Magnet Axial Flux Wind Power
Generator. ISBN 978-1-60643-379-9.
[2] Azzouzi J., Barakat G. and B. Dayko. 2005. Quasi-3D
analytical modeling of the magnetic field of an axial
flux permanent-magnet synchronous machine. IEEE
Trans. On Energy Conversion. 20(4): 746-752.
[3] P. Ferreira and A. F. Costa. 2011. International
Conference on Renewable Energies and Power
Quality. (ICREPQ’11).
[4] Las Palmas de Gran Canaria (Spain), 13th
to 15th
April,
2010, Direct Driven Axial Flux Permanent Magnet
Generator for Small-Scale Wind Power Applications.
[5] We Power. 2010, October, 2010. We Power,
Sustainable Energy Solutions. Available:
http://www.wepower.us/
[6] QuietRevolution. 2010, October, 2010.
Available:http://www.quietrevolution.com/.
[7] E. Muljadi,C.P., Butterfield, Yih-Huei Wan. 1998.
Axial Flux, Modular, Permanent-Magnet Generator
with a Toroidal Winding for Wind Turbine
Applications. NREL/CP-500-24996. UC Category:
1213.
[8] Thomas Valone. 2005. Feasibility study of zero-point
energy extraction from the quantum vacuum for the
performance of useful work. ISBN 0-9641070-8-2.
[9] AsgharSafari-Doust and Abbas Rezaey. 2012. A
Brushless Axial Flux Permanent Magnet Generator
with Two Mechanical PowersInputs for Marine
Current Energy Generation. ISSN 2090-4304.
[10]New energy technologies. Perendev motor. Issue No.
(4)19.
[11]Heins.G,Thiele.M,Patterson.D,Lambert.N. 2014.
Increase in operating range and efficiency for variable
gap axial flux motors. Energy Conversion Congress
and Exposition (ECCE), 2014 IEEE.

Zero point energy conversion for selfsustained generation

More Related Content

What's hot (20)

Similar to Zero point energy conversion for selfsustained generation (20)

Recently uploaded (20)

Zero point energy conversion for selfsustained generation