01 Ipv6 Addressing
Download as PPT, PDF0 likes482 views
The document discusses IPv6 addressing, including historical aspects, types of IPv6 addresses like unicast and multicast, interface identifiers, and address deployment schemes. It provides details on aggregatable global unicast addresses which aim to minimize the global routing table size through allocation hierarchies. The Abilene network's IPv6 allocations and procedures for obtaining addresses are also summarized.
![Obtaining Addresses If you are a Gigapop or a direct connect send a note to Abilene NOC ( [email_address] ) with a request. Will set wheels in motion If you connect to a gigapop you should obtain your address block from that gigapop. Remember the minimum you should receive is a /48. More is ok if you can negotiate for a larger block.](https://image.slidesharecdn.com/01-ipv6-addressing-090821110058-phpapp02/85/01-Ipv6-Addressing-33-320.jpg)
More Related Content
Similar to 01 Ipv6 Addressing (20)
01 Ipv6 Addressing
- 2. Overview of Addressing Historical aspects Types of IPv6 addresses Work-in-progress Abilene IPv6 addressing
- 3. Historical Aspects of IPv6 IPv4 address space not big enough Can’t get needed addresses (particularly outside Americas) Routing table issues Resort to private (RFC1918) addresses Competing plans to address problem Some 64-bit, some 128-bit Current scheme unveiled at Toronto IETF (July 1994)
- 4. Private Address Space Led to the development of NAT. Increased use of NAT has had an effect on the uses the Internet may be put to. Due to the loss of transparency Increasingly could lead to a bifurcation of the Internet. Application rich Application poor Affects our ability to manage and diagnose the network.
- 5. Types of IPv6 Addresses Like IPv4… Unicast An identifier for a single interface. A packet sent to a unicast address is delivered to the interface identified by that address. Multicast An identifier for a set of interfaces (typically belonging to different nodes). A packet sent to a multicast address is delivered to all interfaces identified by that address. Anycast: An identifier for a set of interfaces (typically belonging to different nodes). A packet sent to an anycast address is delivered to one of the interfaces identified by that address (the "nearest" one, according to the routing protocols' measure of distance). Specified in the the v6 address architecture RFC.
- 6. What is not in IPv6 Broadcast There is no broadcast in IPv6. This functionality is taken over by multicast. A consequence of this is that the all 0’s and all 1’s addresses are legal. There are others also we will see later.
- 7. Interface Identifiers Sixty-four bit field Guaranteed unique on subnet Essentially same as EUI-64 Formula for mapping IEEE 802 MAC address into interface identifier Used in many forms of unicast address
- 8. Interface Identifiers IPv6 addresses of all types are assigned to interfaces, not nodes. An IPv6 unicast address refers to a single interface. Since each interface belongs to a single node, any of that node's interfaces' unicast addresses may be used as an identifier for the node. The same interface identifier may be used on multiple interfaces on a single node.
- 9. Interface Identifiers EUI-64 from Mac addresses: 00-02-2D-02-82-34 0202:2dff:fe02:8234 The Rules are: Insert fffe after the first 3 octets Last 3 octets remain the same Invert the 2 nd to the last low order bit of the first octet. Universal/local bit
- 10. Interface Identifiers Privacy addresses: Some concern was expressed about having your MAC address be public. The response was to standardize privacy address. These are random 64 bit numbers. They may change for different connections Right now you will see them in XP and 2000.
- 11. Interface Identifiers A host is required to recognize the following addresses as identifying itself: Its Link-Local Address for each interface Assigned Unicast Addresses Loopback Address All-Nodes Multicast Addresses Solicited-Node Multicast Address for each of its assigned unicast and anycast addresses Multicast Addresses of all other groups to which the host belongs.
- 12. Interface Identifiers Routers are required to recognize: The Subnet-Router anycast addresses for the interfaces it is configured to act as a router on. All other Anycast addresses with which the router has been configured. All-Routers Multicast Addresses All valid host addresses Multicast Addresses of all other groups to which the router belongs.
- 13. Representation of Addresses All addresses are 128 bits Write as sequence of eight sets of four hex digits (16 bits each) separated by colons Leading zeros in group may be omitted Contiguous all-zero groups may be replaced by “::” Only one such group can be replaced
- 14. Examples of Writing Addresses Consider 3ffe:3700:0200:00ff:0000:0000:0000:0001 This can be written as 3ffe:3700:200:ff:0:0:0:1 or 3ffe:3700:200:ff::1 All three reduction methods are used here .
- 15. Types of Unicast Addresses Unspecified address All zeros (::) Used as source address during initialization Also used in representing default Loopback address Low-order one bit (::1) Same as 127.0.0.1 in IPv4
- 16. Types of Unicast Addresses Link-local address Unique on a subnet Auto configured High-order: FE80::/64 Low-order: interface identifier Routers must not forward any packets with link-local source or destination addresses.
- 17. Types of Unicast Addresses Site-local address Unique to a “site” High-order: FEC0::/48 Low-order: interface identifier Used when a network is isolated and no global address is available.
- 18. Types of Unicast Addresses Mapped IPv4 addresses Of form ::FFFF:a.b.c.d Used by dual-stack machines to communicate over IPv4 using IPv6 addressing Compatible IPv4 addresses Of form ::a.b.c.d Used by IPv6 hosts to communicate over automatic tunnels
- 19. Address Deployment There were many discussions of how to interpret the address space when IPv6 was being developed. Suggestions included: Provider Independent Essentially what v4 does Provider Based Geographical Ostensibly Provider based addressing was selected. It is important to understand the difference between allocation and assignment.
- 20. Provider Based Unicast Addresses Aggregatable global unicast address
- 21. Types of Unicast Addresses Aggregatable global unicast address Used in production IPv6 networks Goal: minimize global routing table size From range 2000::/3 Three fields in /64 prefix 16-bit Top Level Aggregator (TLA) 8-bit reserved 24-bit Next Level Aggregator (NLA) 16-bit Site Level Aggregator (SLA)
- 22. Top-Level Aggregators Allocated by RIRs to transit providers They in turn allocate to customers. In practice, RIRs have adopted “slow-start” strategy Start by allocating /32s Expand to /29s when sufficient use in /32 Eventually move to /16s
- 23. Abilene Allocation Allocated 2001:468::/32 The bit level representation of this is: 0010 0000 0000 0001 : 0000 0010 0110 1000 :: This leaves 32 bits of network space available. We will see later how this is to be used.
- 24. NLAs and SLAs NLAs used by providers for subnetting Allocate blocks to customers Can be multiple levels of hierarchy SLAs used by customers for subnetting Analogous to campus subnets Also can be hierarchical Minimum size is /48
- 25. Current Practice and Aggregation In fact the use of terms like TLA and NLA is not longer in use. However the intent of Provider based addressing is still the same. The goal here is aggregation. As you move up the provider chain many addresses get aggregated into larger blocks. If implemented completely the result would be a default free zone with a very small number of prefixes.
- 26. Other Unicast Addresses Original provider-based Original geographic-based GSE (8+8) Tony Hain’s Internet Draft for provider-independent (geographically-based) addressing
- 27. Anycast Address Interfaces (I > 1) can have the same address. The low-order bits (typically 64 or more ) are zero. A packet sent to that address will be delivered to the topologically closest instance of the set of hosts having that address.
- 28. Multicast Address From FF00::/8 1111 1111 | flgs (4) | scop (4) | group id (112)| Flags 000t T=0 means this is a well known address T=1 means this is a transitory address Low-order 112 bits are group identifier, not interface identifier Scope and Flags are independent of each other Well-known and local is different from well-known and global
- 29. Multicast addresses Scope 0 reserved 1 node-local scope 2 link-local scope 3 (unassigned) 4 (unassigned) 5 site-local scope 6 (unassigned) 7 (unassigned) 8 organization-local scope 9 (unassigned) A (unassigned) B (unassigned) C (unassigned) D (unassigned) E global scope F reserved
- 30. Abilene IPv6 Addressing Two prefixes allocated 3ffe:3700::/24 on 6bone 2001:468::/32 6bone addressing is not in use any more. Current addressing allocation scheme was built on the assumption of /35 being available. This is being reviewed
- 31. Allocation Procedures GigaPoPs allocated /40s Expected to delegate to participants The minimum allocation is a /48 No BCP (yet) for GigaPoP allocation procedures Direct connectors allocated /48s Will (for now) provide addresses to participants behind GigaPoPs which haven’t received IPv6 addresses See WG web site for details
- 32. Registration Procedures Providers allocated TLAs (or sTLAs) must register suballocations ARIN allows rwhois or SWIP For now, Abilene will use SWIP Will eventually adopt rwhois GigaPoPs must also maintain registries Will probably have central Abilene registry
- 33. Obtaining Addresses If you are a Gigapop or a direct connect send a note to Abilene NOC ( [email_address] ) with a request. Will set wheels in motion If you connect to a gigapop you should obtain your address block from that gigapop. Remember the minimum you should receive is a /48. More is ok if you can negotiate for a larger block.
Editor's Notes
- #6: Anycast is there -- we’ll use it someday. Current usefulness limited to 6to4
- #7: Want to do discussion about NAT -- bill owens to do a few slides on NAT
- #8: Not completely different than IPv4, but more thought out and integral to IPv6
- #10: Bill owens to move description about why EUI-64 flipped bits
- #14: Add privacy addressing
- #21: ALL WRONG --- needs to go away. This language doesn’t mean anything anymore. Worth putting in to say “this is what you’ve been hearing,” but won’t ask for a SLA from ARIN
- #22: Might want to consider removing abbreviations -- concept still there although language is changing.
- #23: Still basically correct, but now giving out /32s at start.
- #24: Change to abilene allocation -- need to update drawing
- #25: Want to reference RFC that discusses NLA/SLA language
- #28: First bullet needs to be rewritten to be more accurate. Is second statement accurate??
- #29: Emphasize that multicast is more thought out and not just thrown in.
- #31: Second bullet should be deleted and 3rd should be updated
- #32: Add that gigapops should allocate no less than a /48
- #33: Everyone uses SWIP, will consider rwhois if someone updates it.
- #34: Add “contact your gigapop, if appropriate