Coupling beams design كمرات وجوائز ربط بجدران القص
17 likes6,398 views
The document discusses new replaceable coupling beams designed for shear wall structures, emphasizing their ability to be replaced after earthquake damage due to their composition of elastic and sacrificial elements. The study involved comparing the seismic performance of these new beams with conventional beams through numerical analysis and revealed that the new beams focused damage on the replaceable 'fuse,' making repairs easier. The findings underscore the importance of coupling beams in resisting seismic loads while highlighting the advancements in their design for improved resilience.
More Related Content
Similar to Coupling beams design كمرات وجوائز ربط بجدران القص (20)
Coupling beams design كمرات وجوائز ربط بجدران القص
- 2. 2 P a g e | 2 الربط كمرة تكون ان يمكنcoupling beamمن كانات مع وافقي قطري بشكل التسليح حديد حديدSteel concrete coupling beamيسمى والذيComposite coupling beamمقطع استخدام يتم وعادةI Beam Coupling Beams in High-Rise Core-Wall Structures Shear wall structures are most important lateral-force-resisting-systems that have been shown to be very efficient in resisting seismic loads. But previous earthquake damages showed that the coupling beams were easily damaged in the earthquake and it was often used as an energy dissipation part in structures.
- 7. 7 P a g e | 7 المصري الكود اشتراطات القص جدران ربط كمرات
- 8. 8 P a g e | 8 األمريكي الكود شتراطاتا Aci- code
- 13. 13 P a g e | 1 3 القصية الجدران بين الربط جوائز تصميم
- 14. 14 P a g e | 1 4
- 15. 15 P a g e | 1 5
- 16. 16 P a g e | 1 6
- 17. 17 P a g e | 1 7
- 18. 18 P a g e | 1 8
- 19. 19 P a g e | 1 9
- 20. 20 P a g e | 2 0
- 21. 21 P a g e | 2 1
- 22. 22 P a g e | 2 2
- 23. 23 P a g e | 2 3
- 24. 24 P a g e | 2 4
- 25. 25 P a g e | 2 5
- 26. 26 P a g e | 2 6 SUMMARY A kind of new coupling beams had been designed to be used for shear wall structures, and the common characteristics of the beam was that it could be replaced after earthquake damage. The new replaceable coupling beam was composed of elastic elementsand sacrificial elements (may also called “fuse”). Elastic elements were made of steel reinforced concrete and sacrificial elements, whose shape was a steel I-beam with a diamond-shaped hole in middle cross. Due to the use of sacrificial high energy absorbing elements within these coupling beams, it could absorb and dissipate large amounts of energy prior to its failure. Also, since these sacrificial elements were connected toelastic elements by bolt, it could be easily replaced after damage. In order to study the seismic performance of new replaceable coupling beams before test, two coupled shear wall calculation models were built, of which one shear wall coupling beams was replaceable, the other was the conventional coupling beams. Comprehensive calculation analysis showed that the damage of the new replaceable coupling beams focused on the “fuse”, even the elastic elements ofthe coupling beam keeping intact. In contrast, the destruction of conventional coupling beams focused on the end, and it is difficult to repair the damage. In addition, the four large half-scale models are being produced, to be tested to further study the seismic performance of the new coupling beams by cyclic loading test. Keywords: replaceable coupling beams, elastic elements, sacrificial elements, push-over analysis
- 27. 27 P a g e | 2 7
- 28. 28 P a g e | 2 8 Figure 4.2.The shear wall with replaceable coupling beams 4.2. Static push-over analysis 4.2. Static push-over analysis For a detailed comparison of the seismic performance between conventional shear wall and new shear wall, a static push-over analysis was carried out. An axial load of 1600kN was first applied by prestressed rod until the axial-force-ratio reached0.28. Then, displacement controlled load was applied until inter-story drift angles of both shear wall reached approximately 1/50. The base shear-top displacement curves obtained from the analysis were shown in Fig. 4.3 and Fig. 4.4. By comparing Fig. 4.9 and Fig. 4.10 can be seen, the compression wall would bear more shear than tension wall. Particularly the shear of the compression wall was nearly three times than tension wall in conventional shear wall, which indicated the conventional coupling beams afford more constraint moment to the wall limbs. In contrast, the shear of the compression wall was a little bigger than tension wall in new shear wall, which indicatedthe replaceable coupling beams afforded weak constraint moment to the wall limbs. Because the wall limbs size of two shear wall was the same, so, the bearing capacity of replaceable coupling beams was weaker than the conventional coupling beams.
- 29. 29 P a g e | 2 9
- 30. 30 P a g e | 3 0
- 31. 31 P a g e | 3 1
- 32. 32 P a g e | 3 2 The efficiency of coupled wall systems to resist lateral loads is well known. In order for the desired behavior of the coupled wall system to be attained, the coupling beams must be sufficiently strong and stiff. The coupling beams, however, must also yield before the wall piers, behave in a ductile manner, and exhibit significant energy absorbing characteristics.
- 33. 33 P a g e | 3 3 Figure 5.Coupling beam connection to embedded steel column.
- 34. 34 P a g e | 3 4 CONCLUSIONS . The coupling beams, however, must also yield before the wall piers, behave in a ductile manner and exhibit significant energy absorbing characteristics. This paper reviews the current state of the art for the design of conventional reinforced concrete, diagonally reinforced concrete, steel and composite steel-concrete coupling beams. Although not exhaustive, critical aspects of the design of these systems are presented. In the case of diagonally reinforced concrete coupling beams, only included in ACI provisions for the first time in ACI 318-99,