inductively coupled mass spectrometer
Download as PPTX, PDF13 likes4,390 views
The document describes an inductively coupled plasma mass spectrometer (ICP-MS). ICP-MS works by ionizing a sample with inductively coupled plasma and then using a mass spectrometer to separate and quantify the ions. It can detect metals and some non-metals at very low concentrations. Compared to other techniques, ICP-MS has greater speed, precision, and sensitivity. However, it also introduces more interfering species than some other mass spectrometry methods. ICP-MS has a wide variety of applications including medical, environmental, forensic, and geochemical analysis.
inductively coupled mass spectrometer
- 1. INDUCTIVELY COUPLED MASS SPECTROMETER MANU MOHAN 2016041032
- 2. INDUCTIVELY COUPLED PLASMA MASS SPECTROMETER • Inductively coupled plasma mass spectrometry (ICP-MS) is a type of mass spectrometry which is capable of detecting metals and several non-metals at concentrations as low as one part in 1015 (part per quadrillion, ppq) on non-interfered low-background isotopes. • This is achieved by ionizing the sample with inductively coupled plasma and then using a mass spectrometer to separate and quantify those ions. • Compared to atomic absorption spectroscopy, ICP-MS has greater speed, precision, and sensitivity. However, compared with other types of mass spectrometry, such as thermal ionization mass spectrometry (TIMS) and glow discharge mass spectrometry (GD- MS), ICP-MS introduces many interfering species: argon from the plasma, component gases of air that leak through the cone orifices, and contamination from glassware and the cones.
- 3. • The variety of applications exceeds that of inductively coupled plasma atomic emission spectroscopy and includes isotopic speciation. Due to possible applications in nuclear technologies, ICP-MS hardware is a subject for special exporting regulations.
- 4. INDUCTIVELY COUPLED PLASMA (ICP) • An inductively coupled plasma is a plasma that is energized (ionized) by inductively heating the gas with an electromagnetic coil, and contains a sufficient concentration of ions and electrons to make the gas electrically conductive. Even a partially ionized gas in which as little as 1% of the particles are ionized can have the characteristics of a plasma. • The plasmas used in spectrochemical analysis are essentially electrically neutral, with each positive charge on an ion balanced by a free electron. In these plasmas the positive ions are almost all singly charged and there are few negative ions, so there are nearly equal amounts of ions and electrons in each unit volume of plasma.
- 5. APPLICATIONS OF ICPMS It is mainly used in medical and forensic field mainly toxicology. A physician may use this instrument for heavy metal poisoning, metabolic concerns, liver issues etc. Samples collected include blood, urine, plasma RBCs etc. This instrument is mainly used in environmental field. Including soil water analysis. In forensic field it is used for glass analysis. ICPMS is widely used in geochemistry field for radioactive dating, to analyze relative abundance of different isotopes mainly uranium and lead. In pharmaceutical industry,ICPMS is used for detecting inorganic impurities in pharmaceuticals and their ingredients.
- 7. STEPS IN ANALYSIS • The first step is introduction of of sample. The common used method is the use of analytical nebulizers. • Nebulizer converts liquids into an aerosol, and that aerosol can then be swept into the plasma to create the ions. • The aerosol generated is often treated to limit it to only smallest droplets, commonly by means of a Peltier cooled double pass or cyclonic spray chamber. • Laser ablation is another method. In this method, a pulsed UV laser is focused on the sample and creates a plume of ablated material which can be swept into the plasma.
- 10. PLASMA TORCH • The plasma used in an ICP-MS is made by partially ionizing argon gas (Ar → Ar+ + e−). The energy required for this reaction is obtained by pulsing an alternating electric current in wires that surround the argon gas. • After the sample is injected, the plasma's extreme temperature causes the sample to separate into individual atoms (atomization). Next, the plasma ionizes these atoms (M → M++ e−) so that they can be detected by the mass spectrometer. • An inductively coupled plasma (ICP) for spectrometry is sustained in a torch that consists of three concentric tubes, usually made of quartz. I Inductively coupled plasma
- 11. • The end of this torch is placed inside an induction coil supplied with a radio-frequency electric current. • A flow of argon gas is introduced between the two outermost tubes of the torch and an electrical spark is applied for a short time to introduce free electrons into the gas stream. • . These electrons interact with the radio-frequency magnetic field of the induction coil and are accelerated first in one direction, then the other, as the field changes at high frequency. • The accelerated electrons collide with argon atoms, and sometimes a collision causes an argon atom to part with one of its electrons.
- 12. • The released electron is in turn accelerated by the rapidly changing magnetic field. • The process continues until the rate of release of new electrons in collisions is balanced by the rate of recombination of electrons with argon ions (atoms that have lost an electron). This produces a ‘fireball’ that consists mostly of argon atoms with a rather small fraction of free electrons and argon ions.
- 13. ADVANTAGE OF ARGON • Firstly Argon is abundant and cheaper than other noble gases. • Argon also has a higher first ionization potential than all other elements except He, F, and Ne. • Argon can be purchased for use with the ICP-MS in either a refrigerated liquid or a gas form. • Liquid argon is typically cheaper and can be stored in a greater quantity where as gas form, which is more expensive and takes up more tank space. • If the instrument is in an environment where it gets infrequent use, then buying argon in the gas state will be most appropriate as it will be more than enough to suit smaller run times and gas in the cylinder will remain stable for longer periods of time. • If the ICP-MS is to be used routinely and is on and running for eight or more hours each day for several days a week, then going with liquid argon will be the most suitable.
- 14. TRANSFER OF IONS INTO VACUUM • The carrier gas is sent through the central channel and into the very hot plasma. The sample is then exposed to radio frequency which converts the gas into a plasma. • The high temperature of the plasma is sufficient to cause a very large portion of the sample to form ions. A fraction of the formed ions passes through a ~1 mm hole (sampler cone) and then a ~0.4 mm hole (skimmer cone). The purpose of which is to allow a vacuum that is required by the mass spectrometer. • The vacuum is created and maintained by a series of pumps.
- 15. ION OPTICS • Before mass separation, a beam of positive ions has to be extracted from the plasma and focused into the mass-analyzer. It is important to separate the ions from UV photons, energetic neutrals and from any solid particles that may have been carried into the instrument from the ICP. • A sector ICP-MS will commonly have four sections: an extraction acceleration region, steering lenses, an electrostatic sector and a magnetic sector. • The first region takes ions from the plasma and accelerates them using a high voltage. • The second uses may use a combination of parallel plates, rings, quadropoles, hexapoles and octopoles to steer, shape and focus the beam so that the resulting peaks are symmetrical, flat topped and have high transmission.
- 16. • The electrostatic sector may be before or after the magnetic sector depending on the particular instrument, and reduces the spread in kinetic energy caused by the plasma. • This spread is particularly large for ICP-MS, being larger than Glow Discharge and much larger than TIMS.
- 17. COLLISSION REACTION CELL AND COLLISIONAL REACTION INTERFACE (CRI) • The collision/reaction cell is used to remove interfering ions through ion/neutral reactions. The dynamic reaction cell is located before the quadrupole in the ICP-MS device. • The chamber has a quadrupole and can be filled with reaction (or collision) gases (ammonia, methane, oxygenor hydrogen), with one gas type at a time or a mixture of two of them, which reacts with the introduced sample, eliminating some of the interference. • The collisional reaction interface (CRI) is a mini-collision cell installed in front of the parabolic ion mirror optics that removes interfering ions by injecting a collisional gas (He), or a reactive gas (H2), or a mixture of the two, directly into the plasma as it flows through the skimmer cone and/or the sampler cone.
- 19. Instrument Startup and Daily Performance Check • 1. Turn on gas (Argon). • 2. Check gas pressure in tank (Argon). The delivery pressure should be at least 60psi. • The instrument is always on. • 3. Place sample line in beaker with Mili Q water (disconnect from auto‐sampler if necessary). Place tubing on peristaltic pump. • 4. On the computer, open the ELAN icon. • 5. File → Open Workspace → Daily Performance • Instrument tab → Start (Plasma). • The vacuum pressure should be less than 10‐5 torr. Check that water is being drawn up the tube. • When the ignition sequence is complete, the diagram of the instrument in the window should be green; if not green (e.g. if gas is not in line after changing tank), repeat.
- 20. • 6. The Ready and Plasma lights on the instrument (by the beakers) should be green. • 7. Wait 10‐15 minutes for the plasma to warm up before performing Daily Performance Check. • 8. Fill the beaker labeled daily performance (a quarter to a half) with Daily Performance Check • solution (ELAN 6100 Setup Solution). • 9. Switch the feed tube from the beaker of MiliQ water to the beaker with Daily Performance Solution. Analyze Sample (Start). • 10. When the run is complete, a report will print. To view on screen select Rpt View. In this report:
- 21. a. Mg must be > 50,000 b. In must be > 250,000 c. Ur must be > 200,000 d. Net Intensity mean of CeO should be 3% (0.03) e. Bkgd Intens. Mean should be 1. • 11. If (d) and (e) are not satisfied, wait 5‐15 minutes and run again. • 12. Fill in values in the Log book (Populate all fields, including your name and the date). Place the printed report in the Log and Daily Performance binder located next to the computer.
- 22. THANK YOU