IRJET- Dual Axis Solar Tracking System using LDR Sensors

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 12 | Dec 2018 www.irjet.net p-ISSN: 2395-0072
© 2018, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 1371
Dual Axis Solar Tracking System Using LDR Sensors
Mr. Girish D. shelke1, Mr. Aniket S. Titare2, Prof. U. S. Raut3
1,2UG Scholar, Electrical Engineering(E&P), DESCOET, Dhamangaon (Rly.), Maharashtra, India,
3Assistant Professor, Electrical Engineering(E&P), DESCOET, Dhamangaon (Rly.), Maharashtra, India,
---------------------------------------------------------------------***----------------------------------------------------------------------
Abstract - In this paper a microcontroller is used for dual
axis solar tracking system. As the world population increases
tremendously, the demand of power also increases hence in
future there may be chance of power crisis. Toavoidthepower
crisis to some extend renewablesourcesarepreferredi.e. Solar
energy. In this accurate working of dual axis solar tracking
system is presented. The dual axis solar tracking system
controls elevation and orientation angle of solar panel such
that the panel always maintain perpendicular to the straight.
The results indicated that dual axis solar tracking system is
having low cost, reliable and efficient and it has an overall
efficiency of 8% to 25% more than the fix angle tracking
system
Key Words: Dual axis solar tracking, Efficiency, Orientation
angle, Panel
1. INTRODUCTION
Today's world requires more and more energy every day,
which is against the continuous reduction of existing fossil
fuel resourcesandthegrowingconcernaboutenvironmental
pollution. Therefore, it is obvious that this has pushed
humanity to explore new technologies for the production of
electricity, using clean and renewable sources such as solar
and wind energy.
An important source of renewable energy is solar energy,
which offers a great possibility of conversion into electricity,
which in turn guarantees an important part of the energy
needs of the plant.
Photovoltaic energy (PV Cell) is the conversion principle
used in converting sunlight into electricity. Using the solar
tracking technique, solar panel performance can be
increased by 30%, unlike 60% of fixed installations.
A solar tracking device has a wide range of applications to
improve the use of solar insulation. Therefore, the problem
is to implement a system capable of improving the
production of solar energy by 30% - 40%. A microcontroller
is used to implement the control circuit which is the turning
position and a motor used to orient the solar panel
optimally. The goal of these systems is that the sun beam
that falls perpendicular to the solar panel provides the
maximum solar energy that is used to generate electricity
with maximum energy between 12.00 and 14.00 and the
maximum around noon. When the sun is almost directly on
the solar panel and the minimum energy is used to move the
solar panel, which further increases the efficiency of the
tracker.
1.1 CONCEPTS ON SOLAR RADIATION
The sun, at an estimated temperature of 5800 ° k, emits a
large amount of energy in the form of radiation, which
reaches the planet of the solar system. Sunlight has two
components: the direct beam and the diffused ray. Direct
radiation (also called beam radiation)isthesolarradiationof
the sun which are not dispersed (due to shade). The direct
beam carries around 90% of the solar energy and the
"diffusedsunlight" that carries the rest.Thediffusepartisthe
blue sky on a clear day and increases as a part in cloudy days,
the scattered radiation is the solar radiation that has been
dispersed(completeradiation on cloudy days).Thereflected
radiation is the incident radiation(beamanddiffuse)thathas
been reflected from the earth. The sum of the scattered and
reflected beam radiation is consideredastheglobalradiation
on a surface. Because most of the energy is in the direct
range. Maximizing thecollectionrequiresthesuntobevisible
to the panels for as long as possible
1.2 NEED OF SOLAR TRACKER
The energy brought by the direct beam falls with the
cosine of the angle between the incominglightandthepanel.
Table no.1.2 shows the lost direct power (%) due to the
misalignment (angle i).
Table no-1.2: Direct power lost (%) due to misalignment
(angle i)
The sun travels 360 degrees from eastto westperday,but
in the perspective of any fixed position, the visible portionis
180 degrees during a half-day period. The effects of thelocal
horizon are slightly reduced, causing an effective movement
of around 150 degrees.
A fixed-orientation solar panel between sunrise and
sunset ends will see a 75-degree movement on each side
and, therefore, according to the table above, you will lose
75% of the energy in the morning and at night. Turning the
east and west panels can help recover these losses.Atracker

classification in the east-west direction is known as single-
axis tracking.
The sun also shifts the through 46 degrees north-south
during the period of one year. The same group of panels
located at the intermediate point betweenthetwolocal ends
will see how the sun moves 23 degrees on each side, causing
losses of 8.3%. A tracker that counts both for daily
movement andseasoned motioncalleda double-axistracker.
1.2. TYPES OF SOLAR TRACKER
Mainly there are two types of solar tracker such as:
1) Passive Tracking System
2) Active Tracking System
1) Passive Tracking System
The passive tracking system performs the movement of
the current using a low boiling liquid. This liquidisvaporized
due to the adding heat of the sun and the center of mass
moves so that the system finds the new equilibrium position.
2) Active Tracking System
The two basic types ofactive solar tracker aresingle-axis
tracker and double-shaft tracker.
a) Single Axis Tracker
The single axis tracking system performstheelevationor
azimuth movement for a solar energy system, which of these
movements is desired depends on the technology usedinthe
tracker and the space in which it is mounted. For example,
the parabolic system usesazimuth tracking, while many roof
photovoltaic system uses elevation detection due to lack of
space. A single-axis tracker can only rotate at a point both
horizontally and vertically. This makes it less complicated
and generally cheaper than a two-axis tracker, but also less
effective in collecting the total solar energy availableatasite.
The tracker uses motors and gears to direct the locator as
ordered by a controller that responds to the solar direction.
Since the engine consumes energy, it is necessary to used it
when required. The mono axial tracker has a degree of
freedom that acts as a rotation axis. There are several
common implementations of the single-axis tracker. A
horizontal axis tracker consists of a long horizontal tube to
which the solar modules areconnected.Thetubeisalignedin
a north-south direction, is supported by a bearing mounted
on frame and rotates slowly on its axis to follow the
movement of suns in the sky. This type of tracker is more
effective in the equatorial latitudes where the sun is more or
less above midday. In general, it is effective when the solar
path is high in the sky duringthe substantialpartsoftheyear,
but for the same reason, it does not work well at high
latitudes. For higher latitudes, a vertical axis tracker is more
suitable. It works well anywhere the sun is typically lower in
the sky and,at least in the summer months, the daysarelong.
b) Double-Axis Tracker
Dual-axis tracker has two degrees of freedom that act as
axes of rotation. The dual-axis solar tracker, as suggested by
the same, can rotate simultaneously in the horizontal and
vertical direction and, therefore, can accuratelypointthesun
at any time and in any position. The dual axis tracking
systems perform the movements along the elevation and
azimuth axes. These trackingsystems naturallyofferthebest
pre-processing, as the component also has a sufficiently high
accuracy.
2. THE HARDWARE SYSTEM
A general block diagram of the system is shown in fig. 2. The
hardware system consists of various components. The
functions of each components of the system are described as
follows:
Fig.2: - Block Diagram
2.1 SENSOR
In thissystem weusefivelight-dependentresistors(LDRs)as
sensors. They perceive the area with the highest density of
sunlight. The solar panel moves to the high-density area of
light through the servomotors. Each LDR is connected to the
power supply that forms a potential splitter. Therefore, any
variation in light density is proportional to the voltage
variation in the LDR shown in fig. 2.1.
Fig: - 2.1. Sensor
LDR is a passive transducer, so there is used of the potential
divider circuit to get the corresponding voltage value of the
LDR resistor. The LDR resistance is inversely proportionalto
the intensity of the light that falls on it i.e. to a greater
intensity or luminosity of light, lower resistance and vice
versa.

2.2 MICRO-CONTROLLER
The ATMEGA-168 is an 8-bit single-chip microcontroller of
the modified Harvard architecture developed by Atmel. It
uses flash memory in the program storage chip, unlike the
programmable ROM of a single use, the EPROM or EEPROM
that other microcontrollers use at that time. Fig. 2.2 shows
pin diagram of atmega-168.
Fig: - 2.2 Micro-Controller
2.3 DC SERVOMOTOR
By itself, the standard DC motor is not an acceptable method
for controlling a solar tracking matrix. This is due to the fact
that DC motors are free and therefore, difficult for accurate
position. Even if the synchronization to start and stop the
engine is correct, the armature does not stop immediately,
the DC motor has very gradual acceleration and deceleration
curves, so the stabilization is slow.Addinggearstotheengine
will help to reduce this problem, but theexcessisstillpresent
and will eliminate the initial stopping position. The only way
to effectively use a DC motor for precise positioning is to use
a servo. The servomotor is actually a set of four things: a
normal DC motor, a reducer, a position detection device
(usually a potentiometer) and a control circuit. The servo
function is to receive a control signal that represents the
desired output of the servo axis and apply power to the DC
motor until its axis is in that position. Use the position
detection device to determine the rotation position of the
shaft, so it is knowing that how the motor should rotate to
move the axis to the driveposition.Thesolarpanelconnected
to the engine will react according to the direction of the
engine.
2.4 BATTERY
The battery isa series of electrochemical cells for the storage
of electricity, connected individually and housed in a single
unit. An electric battery is a device made up of one or more
electrochemical cells that convertthestoredchemicalenergy
into electrical energy. Each cell contains a positive terminal,
or cathode, and a negativeterminaloranode.Theelectrolytes
allow the ions to move between the electrodes and the
terminals, allowing the current to flow from the battery to
carry out the work. Lead-acidbatteriesarethemostcommon
in photovoltaic systems because theirinitialcostislowerand
because they are available almost anywhere in the world.
There are different sizes and designs of lead-acid batteries,
but the most important designation is that they are deep-
cycle batteries. Lead-acid batteries are available both in the
wet cell (maintenance required) and in the sealed version
without maintenance. Lead acid batteries are reliable and
affordable withexceptionaldurability.Leadacidbatteriesare
highly reliable due to their ability to withstand overload and
vibration. The use of special sealing techniques ensures that
our batteries are leak-proof and do not ruin. The batteries
have an exceptional load acceptance, a large volume of
electrolyte andalowself-discharge,makingthemidealaslow
maintenance lead-free batteries. The batteries are
manufactured tested using CAD (Computer Aided Design).
These batteries are used in inverter and UPS systems and
have the proven ability to operatein extremeconditions.The
batteries have a volume of electrolyte, use PE (Potential
Energy) separators and are sealed in sturdy containers,
which provide excellent protection against leakage and
corrosion.
2.5 SOLAR PANEL
In thissystem,amonocrystallinephotovoltaicsolarpanel(m-
Si) is used, chosen for its good efficiency, lower installation
cost, built-in energy. The monocrystalline photovoltaic solar
panels are not dangerous for the environment, greater heat
resistance and increased electrical generation. This 10 W
solar panel is a combination of a solar cell that generates a
maximum of 10 W of electricity when exposed to sunlight.
Leaves from 2 V to 20 V depending on the intensity of
sunlight and comes with two cables finished with crocodile
clips (black and red). With a medium size (78 mm × 26 mm)
and a light weight (1.2 kg), it is suitable for a variety of
applications.
3. WORKING
The main aim of the dual axissolar trackingsystemistotrack
the sun position and collect the maximum amount of solar
energy to obtained the maximumoutput.Inordertotrackthe
solar radiation veryaccurately. In the dualaxissolartracking
system LDR sensors i.e. lightresistance sensorsare used and
to store the amount of energyproducebysolarpanelwhichis
converted into electrical battery for used. When sunrise
occursat that time the position of sun is at east i.e. horizontal
to the solar tracking system. Hence the LDR sense the
accurate position of sun by using solar radiation and gives
signal to the microcontroller. By receiving signal from LDR
microcontroller produces signal to adjust the positioning of
the motor such that it can perpendicular to the direction of
solar radiation. The dual axis solar tracking system always
take care of the position of solar panel such that they always
perpendicular to the direction of incident radiation i.e.
photons. As these radiation falls on the solar panel i.e.
photovoltaic cells and energy produced is stored in the
battery for the further used. Inverter circuit is also used to
covert DC supply into AC supply.
4. CONCLUSION
In this paper, dual axis tracker system perfectly aligns with
the sun direction and tracks the sun movement in more
efficient way is presented. The results show that dual axis

tracking system is superior than the singleaxissolartracking
system. Power captured by dual axis solar tracking system is
high during the whole time period and it maximize the
conversion of solar radiation into electrical energy output.
The system is cost effective, reliable and efficient. From this
paper, it isconcluded that dual axis solar trackingsystemhas
an increased energy of about 17%-25% more than the fixed
angle system.
5. ACKNOWLEDGMENT
We take this opportunity to express our gratitude and
indebtedness to our guide Ms. U. S. Raut, Assistant Professor,
Electrical (E & P) Engineering department, who has been
constantsource of guidance and inspiration inpreparingthis
paper.
REFERENCES
[1] A.K. Suria, R. Mohamad Idris, “Dual-Axis Solar Tracker
Based On Predictive Control Algorithms,” 9781-4799-
8598-2/15/$31.00 ©2015 IEEE.
[2] Anita Khanna,“Efficient Vertical Dual -Axis Solar
Tracking System,” 978-1-4673-8743-9/16/ $31.00 ©
2016 IEEE.
[3] C. Sungur, “Multi- axes sun- tracking system with plc
control for photovoltaic panels in turkey,” Renewable
Energy, vol. 34, no. 4, pp. 1119–1125, 2009.
[4] Dimitrija Angelkov, Natasa Koceska, Saso Koceski,”
Low- cost Dual- axis System for Solar Tracking,” 3rd
Mediterranean Conference on Embedded Computing
Budva, Montenegro, 2014.
[5] Hengyu Li, Chongyang Zhao, Hao Wang, Shaorong Xie,
Jun Luo, “An Improved PV System Based on Dual Axis
Solar Tracking and MPPT,” InternationalConference on
Mechatronics and Automation August 3 – 6, Tianjin,
China.
[6] Midriem Mirdanies, Roni Permana Saputra, “Dual-axis
Solar Tracking System,” International Conference on
Sustainable Energy Engineering and Application,2016.

IRJET- Dual Axis Solar Tracking System using LDR Sensors

More Related Content

What's hot (20)

Similar to IRJET- Dual Axis Solar Tracking System using LDR Sensors (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Dual Axis Solar Tracking System using LDR Sensors