part 1 .pdf.pdf

Part : 1
Reservoir Engineering
Fundamentals of petroleum Engineering
By
Petroleum Engineer
Abbas Radhi Abbas
Iraq / Missan / 2020
1

2.Introduction to Reservoir Engineering
3.Type of Hydrocarbon Reservoir Traps
4.Basic Rock and Fluid Properties
6.Determined hydrocarbon in place
7.Enhanced Oil Recovery (EOR)
5.Reservoir Classifications
8.Reservoir Surveillance
Contents
1.Reservoir Engineering Functions
9.Tracer Techniques
10. Reservoir management
Contents
Reservoir
Engineering
Fundamentals
2

(1) Reservoir Engineering Functions
3

Reservoir engineers often specialize in two areas:
(1) Reservoir Surveillance
(2) Simulation modeling
Surveillance Engineer
1. monitoring of existing
fields and optimization of
production and injection
rates.
2. Surveillance engineers
typically use production
data , well test , cased
hole logging … etc to
control the production and
injection then diagnose
production problems
3. Use software such as (
Pipsim , OFM , prosper ,
kappa … etc )
Simulation modeling
Engineer :
1. conduct of reservoir
simulation studies to
determine optimal
development plans
for oil and gas
reservoirs.
2. Use software such as
Petrel-RE , Eclipse ,
CMG ….etc

❖ Detailed understanding of the reservoir, including rock and fluid flow
characteristics, and the mechanisms by which a reservoir is produced;
unconventional reservoirs pose new challenges .
Reservoir engineering functions
❑ Reservoir Fluid Properties can
Estimated from PVT sample
• Oil Compressibility
• Oil Viscosity
• Oil Density
• Oil Formation Volume Factor
• Gas Formation Volume factor
• Gas-Oil Ratio
• Bubble point pressure
❑ Rock Properties can estimate
from ( core – log – well test )
1. Porosity
2. Permeability
3. Wettability
4. Saturation
5. Capillary Pressure
Rock and Fluid Properties

❖ Estimation of oil and gas in place (OOIP , OGIP) , reserves & Recovery factor
Determined hydrocarbon in place
OOIP ,OGIP
Determine Reserves Determine Recovery factor
1. Volumetric method
2. Material Balance
1. Analogy,
2. Decline analysis,
3. Data mining,
4. Analytical,
5. Simulation.
RF = Reserve / OOIP
Reference for information

❖ Estimation of oil and
gas in place (OOIP ,
OGIP) , reserves &
Recovery factor

❖ Design, placement, and completion of producers and injectors in order to
optimize production
❖ Plan, design, execution, and monitoring of water flood and enhanced oil
recovery operations
❖ Implementation of a strategy for incremental oil recovery from matured fields
❖ Meeting challenges posed by declining well productivity, premature
breakthrough of water and gas, unexpected reservoir heterogeneities,
operational issues, economic aspects, environmental concerns, statutory
regulations, and others
❖ Development and simulation of computer-based models that predict reservoir
performance

❖ Reservoir surveillance that enhances the knowledge of the reservoir and charts future
courses of action
❖ Working closely with a multidisciplinary team of engineers and earth
scientists in order to manage the reservoir effectively

Some of the jobs description of a reservoir engineer but are not limited
are stated below:
➢ Estimation of the original hydrocarbon in place (OHCIP)
➢ Calculation of the hydrocarbon recovery factor, and
➢ Attachment of a time scale to the hydrocarbon recovery
➢ Good experience in constructing numerical reservoir simulation models
(blackoil and compositional), model initialization, history matching, running
sensitivities and predictions.
➢ Determination of reservoirs, field development strategy, production rates,
reservoir monitoring plan, and economic life.
➢ Involvement of work with an integrated team of geologists, geophysicists,
petrophysicists, and engineers from other disciplines
➢ Knowledge of PVT data analysis.
➢ Collecting, analyzing, validating, and managing data related to the project
➢ Carrying out reservoir simulation studies, either for facts finding or to
hydrocarbon recoveries.
jobs description of a reservoir engineer

Continue…. jobs description of a reservoir engineer
➢ Predicting reserves and performance from well proposals.
➢ Predicting and evaluating gas injection/waterflood and enhanced recovery
performance.
➢ Developing and applying reservoir optimization techniques.
➢ Developing cost-effective reservoir monitoring and surveillance programs.
➢ Performing reservoir characterization studies.
➢ Analyzing pressure transients.
➢ Designing and coordinating petrophysical studies.
➢ Analyzing the economics and risk assessments of major development
programs.
➢ Estimating reserves for producing properties.
jobs description of a reservoir engineer

2-Introduction to Reservoir Engineering
13

The reservoir engineer in the
multi-disciplinary perspective of
modern oil and gas
field management is located at
the heart of many of the activities
acting as a central
co-ordinating role in relation to
receiving information processing
it and passing it on
to others.
14

The activities of reservoir engineering fall into the following three general categories:
Activities
of
Reservoir
Engineering
(A) Reserves Estimation
(B) Development Planning
(C) Production Operations Optimization
15

The Society of Petroleum Engineers SPE and World Petroleum Congress WPO1987
agreed classification of reserves3 provides a valuable standard by which to define
reserves, the section below is based on this classification document. :
16

(A) Proven Reserves
Proven reserves are those quantities of petroleum which, by analysis of geological
and engineering data, can be estimated with reasonable certainty to be commercially
recoverable, from a given date forward, from known reservoirs and under current
economic conditions, operating methods, and government regulations.
There should be at least a 90 percent probability (P90) that the quantities actually
recovered will equal or exceed the estimate.
Reserves :
are those quantities of petroleum which are anticipated to be commercially
recovered from known accumulations from a given date forward.
17

1-Probable Reserves
•Those additional reserves that analysis of geoscience and engineering data indicate are less
likely to be recovered than proved reserves but more certain to be recovered than possible
reserves.
•There should be at least a 50 percent probability (P50) that the quantities actually recovered
will equal or exceed the estimate...
2-Possible Reserves
•Those additional reserves that analysis of geoscience and engineering data suggest are less
likely to be recoverable than probable reserves.
•There should be at least a 10 percent probability (P10) that the quantities actually recovered
will equal or exceed the estimate.
(B) Unproved Reserves
Unproved reserves are based on geologic and/or engineering data similar to that
used in estimates of proved reserves; but technical, contractual, economic, or
regulatory uncertainties preclude such reserves being classified as proved.
Unproved reserves may be further classified as probable reserves and possible reserves.
18

Relationships between parameters related with OOIP , RF and Reserve
RESERVES : Reserves are simply the oil or gas in place times the RF.
for an oil reservoir:
for a gas reservoir:
Recovery Factor ( RF)
19

Relationships between parameters related with OOIP , RF and Reserve
20
OOIP
RF
Reserves = OOIP X RF
OOIP : Original Oil in place
RF : Recovery factor

Variations of reserves During filed life
21

(B) Development Planning
1. Static model
2. Dynamic Model
3. Techno-economics
4. Uncertainty
The following list summarises some of the principal uncertainties associated
with the performance of the overall reservoir model. The type of data can
for example be subdivided into two aspects “static” and “dynamic” data .
Static Properties
• Reservoir structure
• Reservoir properties
• Reservoir sand connectivity
• Impact of faults
• “thief” sands
Dynamic Properties
• Relative permeability etc
• Fluid properties
• Aquifer behavior
• Well productivity (fractures, well-type, condensate drop out etc.)
22

1-History Matching
The purpose of history matching is to calibrate the numerical simulation model so that
it can be used to reasonably predict the future performance of the reservoir(s) under
various development and operating scenarios
23

2-Phases of Development
During the development there are a number of phases. Not all of these phases may be
part of the plan. There is the initial production build up to the capacity of the facility
There is the plateau phase where the reservoir is produced at a capacity limited by the
associated production and processing facilities. Different companies work with
different lengths of the plateau phase and each project will have its own duration.
There comes a point when the reservoir is no longer able to deliver fluids at this
capacity and the reservoir goes into the decline phase. The
decline phase can be delayed by assisting the reservoir to produce the fluids by the use
of for example ‘lifting’ techniques such as down-hole pumps and gas lift. The decline
phase is often a difficult period to model and yet it can represent a significant amount
of the reserves
24

Phases of Production
25

Primary , secondary & Tertiary recovery
26

(3) Type of Hydrocarbon Reservoir Traps
27

(3) Type of Hydrocarbon Reservoir Traps
28

Structural Traps
Structural Traps
Structural traps are created by the deformation of rock strata within the earth’s crust. This
deformation can be caused by horizontal compression or tension, vertical movement and
differential compaction, which results in the folding, tilting and faulting within sedimentary
rock formations
Fault Trap
The faulting of
stratified rock occurs as a result of
vertical and horizontal stress. At
some point the rock layers break,
resulting in the rock faces along the
fracture moving or slipping past
each other into an offset position.
A fault trap is formed when the
faulted formations are tilted toward
the vertical. When a non-porous
rock face is moved into a position
above and opposite a porous rock
face, it seals off the natural flow of
the hydrocarbons allowing them to
accumulate.
29

Structural Traps
Fold (Anticlinal) and Dome Trap
The rock layers
in an anticlinal trap were
originally laid down
horizontally then folded
upward into an arch or
dome. Later,
hydrocarbons migrate
into the porous and
permeable reservoir
rock. A cap or seal
(impermeable layer of
rock) is required to
permit the accumulation
of the hydrocarbon
30

Stratigraphic Traps
Stratigraphic traps
are formed as a
result of differences or variations
between or within stratified rock
layers, creating a change or loss of
permeability from one area to
another. These traps do not occur
as
a result of movement of the strata.
31

Combination Traps
Salt Dome or Salt Plug Trap
A trap created by piercement or
intrusion of stratified rock layers from
below by ductile nonporous salt. The
intrusion causes the lower formations
nearest the intrusion to be uplifted and
truncated along the sides of the
intrusion, while layers above are
uplifted creating a dome or anticlinal
folding. Hydrocarbons migrate into
the porous and permeable beds on the
sides of the column of salt.
Hydrocarbons accumulate in the traps
around the outside of the salt plug if a
seal or cap rock is present.
32

34
Structural traps caused by folding

35
Structural traps caused by faulting

36
The principal types of stratigraphic traps

37
Examples of"combination" traps

(4) Basic Rock and Fluid Properties
38

(4) Basic Rock and Fluid Properties
There are four fundamental types of properties of a hydrocarbon reservoir
that control its initial contents, behavior, production potential, and hence
its reserves.
1. The rock properties of porosity, permeability, and compressibility, which
are all dependent on solid grain/particle arrangements and packing.
2. The wettability properties, capillary pressure, phase saturation, and relative
permeability, which are dependent on interfacial forces between the
solid and the water and hydrocarbon phases.
3. The initial ingress of hydrocarbons into the reservoir trap and the
thermodynamics of the resulting reservoir mixture composition.
4. Reservoir fluid properties, phase compositions, behavior of the phases
with pressure, phase density, and viscosity.
39

Basic Rock Properties
❑Rock Properties
1. Porosity
2. Permeability
3. Wettability
4. Saturation
40

Generally can estimate rock properties from core Analysis , logs , see the
SCAL and RCAL
Routine Core Analysis Special Core Analysis
41

1-Porosity:
is defined as the ratio of pore volume to total rock volume:
Where :
Vp = pore space volume
Vb = bulk volume
Porosity Measurements :Porosity is measured in two ways :
1. from wire line logs
2. Laboratory measurement on core
1-Porosity from wire line logging :
Porosity can be estimated from interpretation of wire line logs, in particular
Acoustic ( sonic) , neutron, Density & NMR logs.
42

2-Porosity Laboratory measurement on core:
Porosity is calculated using the following equation:
Where :
Vp : pore space volume
Vm : matrix (solid rock) volume
Vb : bulk volume (Vp + Vm)
Bulk volume (Vb) can be determined directly from core dimensions
if we have a fluid-saturated regularly shaped core (normally cylindrical),
or by fluid displacement methods by weight where the density of the
solid matrix and the displacing fluid is known, or directly by volume
displacement.
Matrix volume (Vm) can be calculated from the mass of a dry sample
divided by the matrix density. It is also possible to crush the dry solid and
measure its volume by displacement, but this will give total porosity rather
than effective (interconnected) porosity.
43

Boyle’s law : used to calculate the
matrix volume present in the
second
cell using Boyle’s law .This method
can be very accurate, especially
for low-porosity rock.
Boyle’s law: P1V1 = P2V2
(assuming gas deviation factor Z
can be
ignored at relatively low pressures)
can now be used.
Pore space volume (Vp) can also
be determined using gas
expansion
methods.
44

2-Permeability :
Permeability: Is the property a rock has to transmit fluids. It is related to
porosity but is not always dependent upon it. Permeability is controlled by the
size of the connecting passages (pore throats or capillaries) between pores. It
is measured in darcies or milli-darcies
absolute permeability : the ability of a rock to transmit a single fluid when it is
100% saturated with that fluid
Effective permeability : refers to the presence of two fluids in a rock, and is the
ability of the rock to transmit a fluid in the presence of another fluid when the
two fluids are immiscible
Relative permeability : is the ratio between effective permeability of fluid at
partial saturation, and the permeability at 100% saturation (absolute
permeability).
45

relative permeability
To account for the effect of multiple fluids,
relative permeability's are defined as follows:
Water oil relative permeability
Typical relative permeability curves for oil
and water are shown in Figure Oil
permeability decreases monotically from its
maximum at the irreducible water saturation,
krowe, to zero at the residual oil saturation to
water. Water permeability increases
monotonically from zero at the irreducible
water saturation to a maximum at the
residual oil saturation, krwe.
Typical water- oil relative permeability curves.
46

Gas-oil relative permeability
Gas-oil permeabilities are usually
measured in samples presaturated
with water so that irreducible water
is present in the sample as it would
be in the reservoir. The relative
permeabilities of oil and gas are
plotted against either liquid (oil plus
water)
Typical Gas- oil relative permeability curves.
47

Measurement of Relative Permeability
There are two ways of measuring relative permeabilities in the laboratory.
1. Steady-state methods.
2. Unsteady-state methods.
Steady-state methods involve the simultaneous injection of two or more
phases into a core of porous material. The flow ratio is fixed, and the test
proceeds until an equilibrium is reached such that the pressure drop across
the core has stabilized. The data obtained are used with Darcy’s law to
calculate the relative permeabilities of each phase. The flow ratio is changed
to give relative permeabilities over the full range of saturations.
The advantage of steady-state methods is that it is simple to interpret
resulting data. It is, however, time-consuming since a steady state can take
many hours to achieve.
Unsteady-state methods are an indirect technique in which the relative
permeabilities are determined from the results of a simple displacement test.
Flow-rate data for each phase are obtained from the point at which the
injected phase breaks through and we have two-phase flow
48

1. From Core (Laboratory Determination of Permeability)
2. Well test
3. Darcy’s Law in Field Units
4. Formation tester
5. From log and NMR log
Measurement of Permeability :
Vertical and Horizontal Permeability :
It is normally (but not always) assumed that horizontal permeability is the
same in each direction; but vertical permeability is often, and particularly in
clastics, significantly smaller than horizontal permeability when sediments
are frequently poorly sorted, angular, and irregular. Vertical/horizontal
(kv/kh) values are typically in the range 0.01- 0.1.
49

1. From Core (Laboratory Determination of Permeability)
Laboratory Determination of Permeability Single-phase absolute permeability is
measured on core in a steel cylinder where pressures P1 and P2 are measured
for a given gas flow rate Q.
For a gas: from Darcy’s law for
horizontal flow,
For an incompressible liquid: for
horizontal flow
Where : Q : volumetric flow rate (cm3/s); A : area (cm2); m : viscosity of
the gas or liquid; P : pressure (atmospheres); x : length of core (cm). This
gives the value for permeability k in Darcy’s equation.
50

2-Permeability From Well-Test
Analysis
For a constant production flow rate Q,
permeability can be estimated from
average formation thickness h, fluid
viscosity m, bottom hole pressure Pw,
initial reservoir pressure Pe at an
assumed undisturbed (still at initial
conditions) distance re from the well
and wellbore radius rw using the
equations.
51

3- from Darcy’s Law in Field Units
In field units the Darcy equation will be
Where :
k is in milli-Darcies (mD);
u is in RB/day/ft2;
dx dp is in psi/ft;
m is in centipoise (cP);
Y is specific gravity (dimensionless)
52

Wettability is the ability of a fluid phase to wet a solid surface preferentially in the
presence of a second immiscible phase. The wetting, or wettability, condition in a
rock–fluid system depends on IFT. Changing the type of rock or fluid can change
IFT and hence the wettability of the system. Adding a chemical such as
surfactant,
polymer, corrosion inhibitor, or scale inhibitor can alter wettability.
Wettability is measured by contact angle, which is always measured through the
denser phase and is related to interfacial energies by
interfacial energy between oil and solid (dyne/cm)
interfacial energy between water and solid (dyne/cm)
interfacial energy, or IFT, between oil and water (dyne/cm)
contact angle at oil–water–solid interface measured through the water phase (degrees)
3-Wettability
53

Contact angles for oil-wet and water-wet examples are illustrated in Figure
(A)
Wettability is usually measured in the laboratory. Table (--) presents
examples
of contact angles for different wetting conditions. Several factors can affect
laboratory measurements of wettability. Wettability can be changed by
contact of the core during coring with drilling fluids or fluids on the rig floor,
and by contact of the core during core handling with oxygen or water from the
atmosphere. Laboratory fluids should also be at reservoir conditions to obtain
the most reliable measurements of wettability.
Wettability
Figure (A)
Table ( --)
54

Special Core Analysis
Several methods are available to
measure a reservoir’s wetting
preference.
❑ Core measurements include
imbibition and centrifuge
❑ capillary pressure measurements
❑ An Amott imbibition test
compares the spontaneous
imbibition of oil and water to the
total saturation change obtained
by flooding. We will also see later
that capillary pressure and
measurements give an idea of
rock wettability
Measuring Wettability
55

Saturation is the proportion of
interconnected pore space
occupied by a given phase. For
a gas –oil-water system
Where:
Sw : water saturation
So : oil saturation
Sg : gas saturation
4-Saturation
Routine Core Analysis
56

Capillary pressure is the pressure difference across the curved interface
formed by two immiscible fluids in a small capillary tube. The pressure
difference is
Where :
Pc : capillary pressure (psi)
Pnw : pressure in non-wetting phase (psi)
Pw : pressure in wetting phase (psi)
5-Capillary Pressure
57

Oil is the non-wetting phase in a water-wet oil–water reservoir. Capillary
pressure
for an oil–water system is
Where :
Po :pressure in the oil phase (psia)
Pw : pressure in the water phase (psia)
Capillary pressure increases with height above the oil–water contact (OWC)
as
water saturation decreases.
Oil–Water Capillary Pressure
58

In gas–oil systems, gas usually behaves as the non-wetting phase, and oil is
the
wetting phase. Capillary pressure between oil and gas in such a system is
Where :
Pg : pressure in the gas phase (psia)
Po : pressure in the oil phase (psia)
Capillary pressure increases with height above the gas–oil contact (GOC) as
the
wetting phase saturation decreases.
Gas–Oil Capillary Pressure
59

Can estimate the Capillary
pressure from special core
analysis ,
Capillary pressure is usually
determined in the laboratory by
centrifuge experiments
that provide a relationship
between capillary pressure Pc
and water saturation Sw. A typical
Pc versus Sw curve has the
following features
Capillary Pressure measurement
60

❑ Reservoir Fluid Properties can Estimated from PVT sample
• Saturation Pressure
• Live Oil Viscosity
• Live Oil Density
• Gas-Oil Ratio
• Bubble point pressure
• Liberated Gas Formation Volume factor
• Incremental Liberated Gas-Gravity
• Cumulative liberated Gas-Gravity
Basic Fluid Properties
61

❑ • Types of fluid Sampling
(1) Sub-surface sampling (Down-hole sampling)
1-DST strings
2-Wireline sample ( MDT – in open hole )
3- Slickline ( cased hole )
(2) Surface sampling
1-Wellhead samples
2-Separator samples
Sub-surface sampling for Oil Reservoirs Subsurface
samples are generally taken with the well shut-in.
The sample should be taken under single-phase
conditions, Pres > Pb The well should be fully
cleaned up A static pressure gradient survey should
be performed either prior to or during sampling to
check for the presence of water at the bottom of the
well
62

Surface sampling for Oil/gas Reservoirs Sampling at the wellhead Valid
fluid samples are only likely to be obtained if the fluid is single-phase at
the wellhead Poses safety hazards (high-pressure fluid...) Sampling at
the separator Easier, safer, cheaper Only reliable surface method if fluid
is two-phase at the wellhead
Wellhead sampling Sample point should be as near wellhead as possible
Separator sampling The most important factor in separator sampling is
stability of conditions Stabilized gas and oil flow rates (and therefore
GOR) Stabilized temperature Stabilized wellhead pressure Gas and
liquid samples should be taken simultaneously, as they are a matched
pair Oil and gas rates must be measured carefully Sample points must
be as close to the separator as possible
63

Separator sampling
64

The following terms are defined for the black oil model:
Bo :oil formation volume factor (rb/stb or m3/scm)
= the ratio of oil volume at reservoir conditions to the oil volume at
surface conditions
Rs : solution gas-oil ratio ratio (SCF=stb or scm=scm)
= the ratio of the standard volume of solution gas dissolved in the
oil at a given pressure to the oil volume at surface conditions
Bg : gas formation volume factor (rb=SCF or m3/scm)
= the ratio of gas volume at a reservoir conditions to the gas
volume at surface conditions
Bw : water formation volume factor (rb=stb or m3/scm)
= the ratio of water volume at reservoir conditions to the water
volume at surface conditions
65

Bubble point pressure (pb)
Bubble point pressure (pb) is the Pressure at which first bubble of gas is released from
reservoir oils
Gas oil ratio (GOR)
Gas oil ratio (GOR)=total associated gas (SCF) / total crude production (STB) @ 60 f, 14.7
psi
Shrinkage factor (SF)
Shrinkage factor (SF) = Stock tank barrel (STB) / reservoir fluid barrel
Fluid Viscosity (µo,g,w)
Is a measure of a fluid's internal resistance to flow
Fluid viscosity depends on pressure, temperature, and fluid composition.
Typical values:
Oil: 0.2 to 30 cp
Gas: 0.01 to 0.05 cp
Water: 0.5 to 1.05 cp
66

Example of Black oil properties
68

(5) Reservoir Classifications
69

70

1. Source rock : (petroleum is produced from where it was generated)
2. Reservoir rock (oil and gas migrated to a separate location from the source rock
1. Conventional – reservoirs that are developed and produced by traditional tools
and techniques; rock and fluid characteristics are favorable for production on a
commercial scale
2. Unconventional – reservoirs that require innovative approaches and emerging
technologies to develop economically due to unfavorable conditions;
unconventional reservoirs are characterized by ultratight formation, extra heavy oil,
or location of the reservoir at great depths, among others
71
According Nature of rock:
According to Technology

1. Single layered
2. Multilayered or stratified (communicating, partially communicating, noncommunicating)
3. Fractured
4. Faulted (sealing, partially sealing, nonsealing)
5. Compartmental
6. Tight (poor oil and gas conductivity characteristics)
7. Highly heterogeneous (rock properties vary significantly)
1. Closed
2. Edge-water drive
3. Bottom-water drive
1. Unconsolidated
2. Consolidated
3. Tight
72
According to Reservoir boundary
According Geologic complexity
According Rock characteristics

1. Onshore
2. Offshore, including deep-sea reservoirs
3. Shallow, including oil sands
4. Deep, including basin-centered reservoirs
1. Steep inclination – dictates location of wells
1. Over-pressured
2. Under-pressured
73
According to Reservoir dip
According to Location
According to Reservoir pressure:

1. Early stage in production
2. Peak production
3. Declining production
4. Matured reservoir)
1. Single-phase flow (oil or gas)
2. Multiphase flow (oil and gas, oil and water, oil, gas and water, gas and water)
3. High water cut
4. High gas/oil ratio
1. Primary (production by natural reservoir energy)
2. Secondary (production augmented by water flooding)
3. Tertiary (production enhanced by injecting chemical, foam, and thermal treatment
74
According to Production characteristics:
According to Reservoir life
According to Mode of production:

1. Sandstone
2. Carbonate
3. Shale, silt, clay
4. Coalbed
5. Salt dome
6. Combinations of the above
1. Black oil
2. Volatile Oil
3. Retrograde condensate gas
4. Wet gas
5. Dry gas
75
According to fluid properties
According to Rock type

1. Solution gas drive
2. Gas Cup drive
3. Water drive
4. Gravity drainage drive
5. Combination drive
1. Single phase gas
2. Gas condensate
3. Under saturated oil
4. saturated oil
76
According to phase behavior
According to drive mechanism

•The Five Reservoir Fluids
1-According to fluid properties
According to fluid properties
1. Black oil
2. Volatile Oil
3. Retrograde condensate gas
4. Wet gas
5. Dry gas
77

Black Oil Reservoirs:
•GOR < 1,000 SCF/STB
•Density less than 45° API
•Reservoir temperatures < 250°F
•Oil FVF < 2.00 (low shrinkage
oils)
•Dark green to black in color
•C7+ composition > 30%
Black Oil Reservoirs:
78

Volatile Oil Reservoirs:
•1,000 < GOR < 8,000 SCF/STB
•Density between 45-60° API
•Oil FVF > 2.00 (high shrinkage
oils)
•Light brown to green in color
•C7+ composition > 12.5%
Volatile Oil Reservoirs:
79

Gas Condensate Reservoirs:
•70,000 < GOR < 100,000
SCF/STB
•Density greater than 60° API
•Light in colour
•C7+ composition < 12.5%
Gas Condensate Reservoirs:
80

Wet Gas Reservoirs:
•GOR > 100,000 SCF/STB
•No liquid is formed in the reservoir.
•Separator conditions lie within
phase envelope and liquid is
produced at surface.
Wet Gas Reservoirs:
81

Dry Gas Reservoirs:
•GOR > 100,000 SCF/STB
•No liquid produced at surface
Dry Gas Reservoirs:
82

Range of Reservoir fluid properties
83

84
Range of Reservoir fluid properties

❑ Any reservoir and formation should know the petro-physical
properties :
1. Porosity
2. Permeability
3. Wettability
4. Saturation
❑ petro-physical properties can calculated from :
1. Well logging
2. Core
3. Well test
2-According to Rock type
❑ Reservoir must be ( porous , permeable & Trapped )
85

1. Clastic Reservoir
2. Carbonate Reservoir
According to Rock type
2-According to Rock type
1-Clastic Reservoir
• Consist primarily of Silicate Mineral ( Quartz SiO2)
• Sandstone porosity ( 10-30 )%
2-Carbonate Reservoir
• Mean limestone and dolomite
• Limestone is better than dolomite for ( porosity and permeability )
86

According to phase behavior
1. Single phase gas
2. Gas condensate
3. Under saturated oil
4. saturated oil
3-According to phase behavior
88

Pressure-temperature phase diagram
for
multicomponent hydrocarbon reservoir
fluid mixture. For
isothermal production in the reservoir:
position A indicates
reservoir fluid found as an under
saturated oil;
position B
indicates reservoir fluid found as a gas
condensate;
position C indicates reservoir fluid
found as a dry gas
Pressure-temperature phase diagram
89

4-According to drive mechanism
According to drive mechanism
1. Solution gas drive
2. Gas Cup drive
3. Water drive
4. Gravity drainage drive
5. Combination drive
Drive Mechanism
The natural energy of the reservoir used to transport hydrocarbons towards and out of the
production wells
.
There are five important drive mechanisms (or combinations).
1. Solution Gas Drive.
2. Gas Cap Drive.
3. Water Drive.
4. Gravity Drainage.
5. Combination or Mixed Drive
A combination or mixed drive occurs when any of the first three drives operate together
or when any of the first three drives operate with the aid of gravity drainage.
90

1- Solution Gas Drive
Solution Gas Drive:
Gas breaks out of solution and
expanding gas maintains pressure
in reservoir somewhat over time
Trend
Characteristics
Declines rapidly and continuously
Reservoir Pressure
then drops
First low then rises to a maximum and
Gas/Oil Ratio
continues to decline First high, then decreases rapidly and
Production Rate
None
Water Production
Requires artificial lift at early stages
Well Behavior
5-30% of original oil-in-place
Expected Oil Recovery
91

Gas Cap Drive:
Gas in gas cap is expanding as pressure
depletes, maintaining pressure somewhat
overtime (later stages of solution gas drive)
2.Gas cap Drive.
Trend
Characteristics
Falls slowly and continuously
Reservoir Pressure
Rises continuously
Gas/Oil Ratio
First high, then declines gradually
Production Rate
Absent or negligible
Water Production
Long flowing life depending on size of gas cap
Well Behavior Cap
20 to 40% of original oil-in-place
Expected Oil
Recovery
92

Water Drive
Large aquifer volume expands
providing pressure for relatively
small oil volume. Can be
supplemented with water injection.
Over time:
3.Water Drive.
Trend
Characteristics
Remains high
Reservoir Pressure
Remains steady
Gas/Oil Ratio
tarts early and increases to appreciable amounts
Water Production
Flow until water production gets excessive
Well Behavior Cap
up to 60% original oil-in-place.
Expected Oil
Recovery
93

Gravity Drainage Drive
Usually for heavy oils with very little or no
gas.
Oil literally is produced as the density of the
oil drops and oil moves under force of
gravity.
Normally accompanied by artificial lift.
Can also be supplemented with water
injection.
Over Time:
➢Reservoir pressure remains low.
➢GOR very low if at all.
4.Gravity Drainage.
94

combination drives : we have a gas cap
with the oil accumulation underlain
by water providing potential water drive
.So both free gas and water are in
contact with the oil.
In such a reservoir some of the energy
will come from the expansion of the gas
and some from the energy within the
massive supporting aquifer and it is
associated compressibility.
5.Combination or Mixed Drive
5.Combination or Mixed Drive
95

Reservoir Drive Indexes from the Material Balance Equation (MBE)
A general Material Balance Equation that can be applied to all reservoir types was
first developed in 1936. Although it is a tank model equation, it can provide great
insight for the practicing reservoir engineer.
Reservoir Drive Indexes from the Material Balance Equation (MBE)
96

(6) Determined hydrocarbon in place
97

Five methods to Determined hydrocarbon in place :
1. Analogy Method
2. Volumetric method
3. Material Balance Method
4. Decline curve analysis Method
5. Reservoir simulation Method
98

1-Analogy method
The analogy method is applied by comparing factors for the analogous and
current fields or wells. A close-to-abandonment analogous field is taken as
an approximate to the current field. This method is most useful when running
the economics on the current field; which is supposed to be an exploratory
field.
2-Volumetric method
The volumetric method, on the other hand, entails determining the areal
extent
of the reservoir, the rock pore volume, and the fluid content within the pore
volume. This provides an estimate of the amount of hydrocarbons-in-place.
The
ultimate recovery, then, can be estimated by using an appropriate recovery
factor.
❑ Each of the factors used in the calculation above have inherent
uncertainties that, when combined, cause significant uncertainties in the
reserves estimate. 99

Volume of Oil Initially In Place (OIIP)
To estimate oil initially volume in place, the following formula is a
volumetric calculation for oil.
Where;
STOIIP = stock tank oil in place, stb
A= area, acre
h = reservoir thickness, ft
ɸ = rock porosity, %
Swc =connate water saturation, %
Boi = oil formation volume factor, rb/stb
Note: the stock tank condition is a standard surface condition of oil and
gas at 60F and 14.7 psia.
100

Volume of Gas Initially In Place (GIIP)
The formula to determine gas in place is listed below;
Where;
G = gas oil in place at standard condition, scf
A= area, acre
h = reservoir thickness, ft
ɸ = rock porosity, %
Swc =connate water saturation, %
Bgi = gas formation volume factor, rcf/scf
Note: This is the same formula as the oil in place but only constant is
different because of volume of gas is reported in cu-ft.
101

3-Material balance calculation
is an excellent tool for estimating
gas reserves. If a reservoir
comprises a closed system and
contains single-phase gas, the
pressure in the reservoir will
decline proportionately to the
amount of gas produced.
Unfortunately, sometimes bottom
water drive in gas reservoirs
contributes to the depletion
mechanism, altering the
performance of the non-ideal gas
law in the reservoir. Under these
conditions, optimistic reserves
estimates can result.
102

4-decline analysis and material balance
As production and pressure data from a field become available, decline analysis
and material balance calculations, become the predominant methods of calculating
reserves. These methods greatly reduce the uncertainty in reserves estimates.
Decline curve relationships are empirical, and rely on uniform, lengthy production
periods. It is more suited to oil wells, which are usually produced against fixed bottom-
hole pressures. In gas wells, however, wellhead back-pressures usually fluctuate,
causing varying production trends and therefore, not as reliable .
The most common decline curve relationship is the constant percentage decline
(exponential). With more and more low productivity wells coming on stream, there
is currently a swing toward decline rates proportional to production rates
(hyperbolic and harmonic). Although some wells exhibit these trends, hyperbolic or
harmonic decline extrapolations should only be used for these specific cases. Overe-
xuberance in the use of hyperbolic or harmonic relationships can result in
excessive reserves estimates
.
103

(7) Enhanced Oil Recovery (EOR)
104

(7) Enhanced Oil Recovery (EOR)
EOR / IOR definition
105

EOR methods : used to improve reservoir recovery efficiency, and explain
their differences For each method, state whether it can improve
displacement, vertical or areal sweep efficiency and explain how it works.
1-Primary recovery
Primary recovery, using ( the natural energy of reservoirs and artificial lift ) ,
typically recovers up to 50% of OOIP (average 19%).
2-Secondary recovery
Secondary recovery involves adding energy to the natural system by
injecting water to maintain pressure and displace oil (also known as water
flood). Typical recoveries are 30-50% of OIP after primary recovery (average
32%).
3-Tertiary recovery
Tertiary recovery includes all other methods used to increase the amount of
oil recovered ( thermal , gas injection , chemical injection , others ) . Typical
recoveries are more than 50% of OIP .
What is the (EOR) ?
106

❑ The goal of any enhanced oil recovery process is to mobilize "remaining" oil.
❑ This is achieved by enhancing oil displacement and volumetric sweep
efficiencies.
❑ Oil displacement efficiency is improved by reducing oil viscosity (e.g.,
thermal floods) or by reducing capillary forces or interfacial tension (e.g.,
miscible floods).
❑ Volumetric sweep efficiency is improved by developing a more favorable
mobility ratio between the injection and the remaining oil-in-place (e.g.,
polymer floods, water alternating- gas processes).
❑ It is important to identify remaining oil and the mechanisms that are
necessary to improve recovery prior to implementing an EOR process.
Objective of EOR
107

❑ Water-flooding : use water
❑ Thermal methods: steam stimulation, steam-flooding, hot water drive, and
in- situ combustion
❑ Chemical methods: polymer, surfactant, caustic, and micellar/polymer
flooding
❑ Miscible methods: hydrocarbon gas, CO2, and nitrogen (flue gas and
partial miscible/immiscible gas injection may also be considered)
EOR methods
108

❑ Description
Water-flooding consists of injecting water into the reservoir. Most widely used
post-primary recovery method. Water is injected in patterns or along the
periphery of the reservoir.
Mechanisms that Improve Recovery Efficiency
• Water drive
• Increased pressure
Limitations
• High oil viscosities result in higher mobility ratios.
• Some heterogeneity is acceptable but avoid extensive fractures.
Challenges
• Poor compatibility between the injected water and reservoir may cause
formation damage
Water-flooding
109

Water-flooding
Different well pattern :
110

To increase ultimate oil production beyond that achievable with primary and
secondary methods, there are a few steps to undertake.
1. First, an improvement of the sweep efficiency must ensue.
2. This is then followed by a reduction of the amount of residual oil in the
swept zone.
3. Thirdly, there must be an increase in the displacement efficiency.
4. And finally, there must be a reduction in the viscosity of thick oils.
Here will explain :
1. Surfactant / Polymer Flooding
2. Polymer Flooding
Chemical oil recovery methods
111

Surfactant / Polymer Flooding
❑ Description
Surfactant / polymer flooding consists of injecting slug that contains water,
surfactant, electrolyte (salt), usually a co-solvent (alcohol), followed by
polymer-thickened water.
• Interfacial tension reduction (improves displacement sweep efficiency).
• Mobility control (improves volumetric sweep efficiency).
Limitations
• An areal sweep of more than 50% for water-flood is desired.
• Relatively homogeneous formation.
• High amounts of anhydrite, gypsum, or clays are undesirable.
112

Challenges
• Complex and expensive system.
• Possibility of chromatographic
separation of chemicals.
• High adsorption of surfactant.
• Interactions between surfactant
and polymer.
• Degradation of chemicals at high
temperature.
Surfactant / Polymer Flooding
113

Polymer Flooding
❑ Description
Polymer augmented waterflooding consists of adding water soluble polymers
to the water before it is injected into the reservoir.
• Mobility control (improves volumetric sweep efficiency).
Limitations
• High oil viscosities require a higher polymer concentration.
• Results are normally better if the polymer flood is started before the water-
oil ratio becomes excessively high.
• Clays increase polymer adsorption.
• Some heterogeneity is acceptable, but avoid extensive fractures.
114

Challenges
• Lower injectivity than with water
can adversely affect oil
production rates in the early
stages of the polymer flood.
• Xanthan gum polymers cost
more, are subject to microbial
degradation, and have a greater
potential for wellbore plugging.
Polymer Flooding
115

Miscible Gas Flooding ( CO2 injection )
❑ Description
CO2 flooding consists of injecting large quantities of CO2 (15% or more
hydrocarbon pore volumes) in the reservoir to form a miscible flood.
• Components from the oil, and, if the pressure is high enough, develops
miscibility to displace oil from the reservoir.
• Viscosity reduction / oil swelling.
Limitations
• Very low viscosity of CO2 results in poor mobility control.
• Availability of CO2
• Surface facilities
116

Challenges
• Early breakthrough of CO2
causes problems.
• Corrosion in the producing wells.
• The necessity of separating CO2
from saleable hydrocarbons.
Repressuring of CO2 for
recycling.
• A large requirement of CO2 per
incremental barrel produced.
Miscible Gas Flooding ( CO2 injection )
117

Miscible Gas Flooding (Hydrocarbon Injection)
❑ Description
Hydrocarbon gas flooding consists of injecting light hydrocarbons through the
reservoir to form a miscible flood.
• Viscosity reduction / oil swelling / condensing or vaporizing gas drive.
Limitations
• Minimum depth is set by the pressure needed to maintain the generated
miscibility. The required pressure ranges from about 1,200-5000 psi for the
high pressure Gas Drive, depending on the oil.
• A steeply dipping formation is very desirable- permits gravity stabilization of
the displacement that normally has an unfavorable mobility ratio.
118

Challenges
• Viscous fingering results in poor
vertical and horizontal sweep
efficiency.
• Large quantities of expensive
products are required.
• Solvent may be trapped and not
recovered
Miscible Gas Flooding (Hydrocarbon Injection)
119

Nitrogen / Flue Gas Flooding
❑ Description
Nitrogen or flue gas injection consists of injecting large quantities of gas that
may be miscible or immiscible depending on the pressure and oil composition.
Large volumes may be injected, because of the low cost.
Nitrogen or flue gas are also considered use as chase gases in the
hydrocarbon-miscible and CO2 floods.
• Vaporizes the lighter components of the crude oil and generates miscibility
if the pressure is high enough.
• Provides a gas drive where a significant portion of the reservoir volume is
filled with low-cost gases.
Limitations
• Miscibility can only be achieved with light oils at high pressures; therefore,
deep reservoirs are needed.
• A steeply dipping reservoir is desired to permit gravity stabilization of the
displacement, which has a very unfavorable mobility ratio.
120

Challenges
• Viscous fingering results in poor
vertical and horizontal sweep
efficiency.
• Flue gas injection can cause
corrosion.
• Non hydrocarbon gases must be
separated from saleable gas
Nitrogen / Flue Gas Flooding
121

Thermal (Steam-flooding)
❑ Description
Steam-flooding consists of injecting about 80% quality steam to displace oil.
Normal practice is to precede and accompany the steam drive by a cyclic
steam simulation of the producing wells (called Huff and Puff).
• Viscosity reduction / steam distillation.
• Thermal expansion.
• Supplies pressure to drive oil to the producing well.
Limitations
• Application to viscous oil in massive, high permeability sandstones or
unconsolidated sands.
• Oil saturations must be high, and pay zones should be > 20 feet thick to
minimize heat losses to adjacent formations.
• Steam-flooded reservoirs should be as shallow as possible, because of
excessive wellbore heat losses.
122

Thermal (Steam-flooding)
More Limitations
• Steam-flooding is not normally done in
carbonate reservoirs.
• Since about 1/3 of the additional oil
recovered is consumed to generate the
required steam, the cost per
incremental barrel of oil is high.
• A low percentage of water-sensitive
clays is desired for good injectivity
Challenges
Adverse mobility ratio and channeling of
steam.
123

Thermal (In SITU COMBUSTION) or "Fire-flooding")
❑ Description
This method is sometimes applied to reservoirs containing oil too viscous or
"heavy" to be produced by conventional means. Burning some of the oil in situ
(in place), creates a combustion zone that moves through the formation toward
production wells, providing a steam drive and an intense gas drive for the
recovery of oil.
124

EOR process maturity curve-with time
125

126

❑ A definition of surveillance
A definition of surveillance that is more suitable for managing hydrocarbon
assets is the : ( continuous process of generating opportunities for improving
reservoir performance )
❑ History of Reservoir Surveillance
Surveillance techniques were first discussed in the SPE literature in the early
1960s . Since then, reference to surveillance has been made, but mostly in the
context of episodic data gathering to monitor performance, primarily in flooding
situations
The four stages of value creation using measurements, in order of increasing
benefits, are
1. Data
2. Information
3. Knowledge
4. Intelligence
127

these stages along with the
characteristics pertaining to each
stage. Significant increase in
effort is required for large gains in
value as the information is
converted to knowledge and then
into intelligence. Intelligence is
gained when we possess the
ability to predict the future for a
parameter, property, or system.
The rapidity with which
companies gain system
intelligence differentiates and
distinguishes them from their
competitors
128

Engineering functions and tasks leading to decisions
129

Relating measurements to interpretation and uncertainty reduction
130

Example 1 : plan to identify thief zones and remediate:
❑ Example 1 : plan to identify thief zones and remediate:
Steps :
1. Develop areal distribution maps of movable oil in place.
2. Based on production/injection data, prepare well connectivity maps.
3. Run injection and production profile surveys.
4. Use petrophysical data, injection surveys, and connectivity maps to identify
correlatable thief zones.
5. Plan appropriate data gathering.
6. Evaluate alternatives for shutoff including production curtailment,
debottlenecking, pattern realignment, and facilities upgrade.
131

Uncertainty management plans (UMP)
the uncertainty about the reservoir, its performance, our ability to forecast, and
new opportunities to improve recovery that makes surveillance so challenging.
During early phases of field development, there are significant uncertainties that
lead to project risks.This Fig. show how uncertainty-management plan sresult in
the definition of technology and surveillance plans for an asset.
Uncertainty management plans (UMP) drive surveillance and technology plans
132

Performance expectations
Performance expectations must be established for all major components of
an asset. This includes wells, reservoirs, fields, equipment, and facility
installations. Defining performance goals and expectations for the assets
provides a valuable basis for future comparison and analysis. Minimum
expectations for asset management include compilation and active
management of the following data streams:
1. Geological maps for the fields including structure maps, isopach maps,
and well-record maps.
2. Mechanical well sketch for each of the wells including tubing and casing
detail as well as wellhead data and other tubing equipment (packers,
liners, nipples, plug back total depth, subsurface safety valves, gas-lift
valve depths, pump depths, etc.).
3. A petrophysical summary for each well that includes formation tops, pay
intervals, net feet of pay, and sand-identification information.
133

Performance expectations
4. An evaluated open-hole log over the entire logged interval.
5. Raw and allocated production data and allocation factors.
6. Rock property data, core data and core-study data, and rock failure data.
7. Fluid properties and pressure-volume-temperature analyses for the wells
and reservoirs.
8. Pressure data—static and buildup from all surveys taken in the field.
9. Authority for expenditure (containing detailed justifications) for each well.
10. Well summary sheet with well histories.
11. Copy of field studies, petrophysical studies, reservoir and geological
studies.
12. Reserve report data.
13. Facility, plant, process flow diagram (PFD), flowline data and drawings.
134

data types, roles, and primary responsibilities
shows an example of a table that may be used to assign data ownership and
responsibility for different sources of information. Such tables are valuable in
the dynamic personnel situation in most companies.
135

parameter for Static and Dynamic Reservoir Information
simple matrix chart that allows one to identify which measurements provide
information for a given parameter for Static Reservoir Information and Dynamic
Reservoir Information
136

This table shows how the
state of knowledge for a
given parameter will
change as a result of using
a particular measurement
technique . This tells us
which method will reduce
the uncertainty in a given
parameter the most
137

This table is constructed with
categorical variables (low,
medium, high). However,
numerical values can
be assigned and then
vertically summed by
columns to establish the
highest value in terms of
uncertainty resolution by a specific tool. Although the table looks relatively
innocuous, a number of considerations are required to populate the low, mid,
high nature of a particular measurement . The consideration should include
• Resolution
•Accuracy
•Repeatability
•Interpretability
•Environment variables that impact tool fidelity 138

Objectives based tools selection for measurements
1
2
3
4
139

5
6
7
140

8
9
10
11
141

12
13
14
15
142

16
17
18
19
143

20
21
22
144

Problem based Diagnostic and tools selection
1
2
3
145

4
5
146

6
147

7
148

8
9
10
149

11
12
150

Problem based job planning tree
Start
End
151

(9) Tracer Techniques used for Reservoir surveillance.
The technologies have existed for over 50 years.
Tracers provide a powerful surveillance technique for understanding reservoir
connectivity and determining remaining oil saturation. Success of secondary and
tertiary oil recovery projects targeting remaining oil in mature or partially
depleted reservoirs strongly depends on appropriate description of reservoir
heterogeneity and remaining oil distribution. Tracers have been used in
groundwater hydrology and chemical industry for a very long time. Applications
in the oil industry have been mixed.
Two types of tracer tests are generally conducted:
1. Single-well tracer tests
2. Inter-well tracer tests
153

1-Single-well tracer tests
Use of single-well tracer tests is widespread. Tracers can be used for estimation
of oil saturation in the vicinity of the wells, determining injection profiles of fluids,
tagged tracer for cement and proppants can be run in a well to determine the
effectiveness of fracture proppant placement or cement quality behind pipe. With
increased use of single-trip, multistage fracturing operations both in
unconventional reservoirs and thick deep water reservoirs, tagged tracers are
being used more often for understanding the quality of completion, proppant
placement, and cement isolation. A more recent development is the use of tracer
cartridges that can be placed in between flowing intervals in production wells.
The tracers are soluble only in water phase and can help determine which
intervals are producing water without the introduction of wireline tools to run
PLTs.
154

2-Inter-well tracer tests
Inter-well tracer tests, if designed and conducted well, can be a powerful tool for
describing a reservoir, investigating unexpected anomalies in flow, verifying
suspected flow barriers, and determining reservoir heterogeneity including
layering. Tracers are also used for determining connectivity between wells,
determining remaining oil saturation and estimating performance of a water-
flood, solvent injection, or steam injection
Common Use of tracers in reservoir managements
1. Determine remaining/residual oil saturation
2. Define well-to-well connectivities
3. Determine the presence of flow barriers
4. Characterize reservoir heterogeneity and layering
5. Compute swept pore volume
6. Assess cement integrity in wellbores
7. Evaluate completion quality and proppant placement
8. Calculate phase dispersivities
155

Tracer Characteristics
A perfect tracer for subsurface reservoir application should have the following
characteristics:
1. Soluble and move at the same speed as the tracer carrier
2. Stable except for radioactive tracer that decay according to their half lives
3. Not absorbed significantly or broken down by chemicals in target formation
4. Should be at negligible or low concentrations in the reservoir (background)
5. Detectable and measurable at low concentrations
6. Cost efficient
7. Safe to inject, produce, and handle
8. Repeatable and standardized analytical equipment for measurement
156

For radioactive tracers, operational safety is the most critical component of
running a tracer program and appropriate attention needs to be paid. From an
operational perspective, overall cost and detectability are important. The
success of a tracer test and its quantitative use is determined by maintaining
material balance in the reservoir. To achieve this, measures should be taken
during tracer selection to make appropriate trade-offs in terms of chemical types,
their dynamic characteristics, and interactions with rocks and fluids.
Tracer Types
157

Commonly Used Tracers in the oilfields
158

Design Considerations.
The generic questions that should be answered are:
1. What are the objectives of the test (reservoir characterization, proppant
placement determination, injection distribution in a well, residual oil saturation
determination, barrier confirmation, sweep efficiency characterization,
breakthrough characteristics, etc.)?
2. Is it a single or a mult-iwell tracer test?
3. What is the impacted reservoir volume (pattern-size, single-well
drainage/injection volume)?
4. What are the feasible tracer types and volumes based on objectives?
5. What are the detectability limits of the selected tracer?
6. What is the maximum permissible tracer concentration?
7. Is the test being designed to answer qualitative connectivity questions or is
quantitative evaluation needed?
8. What is the volume of tracer injection?
159

Design Considerations.
9-What are the analytical techniques used to estimate tracer eluent concentration?
10-What would be the sampling frequency and resulting cost?
11-Is in-line sampling and analysis practical? What is the trade-off between in-line
sampling installation cost vs. lab measurement?
12-Do lab tests need to be conducted to confirm compatibility with reservoir rock,
fluids, and water?
13-Do we understand the adsorption behavior of the tracer in question and the link
to design concentration for detectability?
14-What are the measurement methods and stability of partitioning tracers?
15-Is the partition coefficient constant or do we know the partition coefficient
function for
the tracer?
16-What would be the soak and backflow time for single-well partitioning tracer
tests?
17-What are the field equipment requirements for mixing, injection, and sampling
procedures as well as field procedures for handling?
160

Reservoir Management
Definition of Reservoir Management:
Reservoir Management relies on the use of human, technological and financial
resources to capitalize on profits from a reservoir by optimizing the hydrocarbon
recovery while minimizing both the capital investments and the operating costs.
Main objectives of the reservoir management :
1. Decreasing of the risk
2. Increasing of the oil and gas production
3. Increasing of the oil and gas reserves
4. Minimization of the capital expenditures
5. Minimization of the operating costs
6. Maximizing of the final hydrocarbon recovery
163

The reservoir management process must be designed and implemented to
individual fields on the basis of:
1. Logistics and size of the field/reservoirs
2. Geological complexity of the field/reservoirs
3. Reservoir rock and fluid properties
4. Depletion state
5. Regulatory controls
The modelling process is based on the following main steps:
1-reconstruction of a reservoir geological model
(geological characterization and fluid properties definition)
2-selection of a reservoir mathematical model
(up-scaling and initialization)
3-calibration of the reservoir geological model
(past history matching)
4-prediction of the reservoir future performance
( production forecasts)
165

Reservoir Management Process
166

Developments plan work-flow
167

Data Acquisition and Characterization
1-Data acquisition :
Data acquisition, involving the gathering of raw data from various sources, i.e.
1. Seismic surveys
2. Well logs
3. Conventional and special core analyses
4. Fluid analyses
5. Static and flowing pressure measurements
6. Pressure-transient tests
7. Periodic well production tests
8. Records of the monthly produced volumes of fluids (oil, gas, and water)
9. Records of the monthly injected volumes of IOR/EOR fluids (water, gas,
CO2, steam, chemicals,…).
168

2-Data processing:
Data processing based upon:
1. Seismic time maps
2. Seismic conversion of time-to-depth maps
3. Seismic attribute maps
4. Log analyses
5. Structural maps
6. Cross sections
7. Geologic models
8. Reservoir fluids modeling
9. Simulation models
169

3-Data integration and Reservoir Characterization
The characterization of a reservoir aims at producing the best detailed
geological reconstruction both of its geometry and of its internal
structure. The overall process is, therefore, the first basic step in the
development of a reservoir model, and it must consider all the available
data, processed and interpreted with the best technologies always
caring to be consistent with the observed historical reservoir
performance.
Geophysical, geological, and engineering characterization provides
also information on the initial distribution of the fluids, as well as on the
hydraulic connectivity between different zones of the reservoir rocks.
170

The following activities are
normally performed for the
acquisition of the data required by
the reservoir characterization.
1. Seismic
2. Well Logging
3. Core Analysis
4. Fluid Properties
5. Well Testing
171

1-Seismic
Seismic allows reconstructing the
reservoir geological setting through
different level observations:
1. On large scale: reservoir geometry,
identification of main structural
features (e.g. faults), , etc
2. On small scale: detailed structural
and stratigraphycal features, fluid
contacts, etc.
Seismic response of a reservoir
depends on petro-acoustic properties of
the volume of rock investigated; such
properties can be obtained by the
interpretation of specific field data.
172

Generally can estimate rock properties from core Analysis
Routine Core Analysis Special Core Analysis
3- Core analysis
174

❑ Reservoir Fluid Properties can Estimated from PVT sample
• Saturation Pressure
• Live Oil Viscosity
• Live Oil Density
• Gas-Oil Ratio
• Liberated Gas Formation Volume factor
• Incremental Liberated Gas-Gravity
• Cumulative liberated Gas-Gravity
4- Fluid Properties
175

❑ Type of well test :
1. Static pressure test
2. Drawdown test
3. Build-up test
4. Injection test / fall-off test
5. Interference test and pulse test
6. Gas well test
7. Flow after flow test,
8. Isochronal test,
9. Modified isochronal test
10. DST
5- well test
176

Workflows for integrated reservoir modeling
Integrated Reservoir Modeling
177

reservoir modeling
Integrated Reservoir Modeling
Static Model Dynamic model
1. Structural modeling
2. Stratigraphic modeling
3. Lithological modeling
4. Petrophysical modeling
1. Up-scaling
2. simulation
3. History matching
178

Static Model
1. Structural modeling
Reconstruction of the geometrical and
structural properties of the reservoir, by
defining a map of its structural top and
the set of faults running through it. This
stage of the work is carried out by
integrating interpretations of the
geophysical surveys with the available
well data.
(I) Static Model
179

Static Model
2. Stratigraphic modeling
Definition of a stratigraphic scheme
using well data, which form the basis
for well to well correlations. The data
consist of electrical, acoustic and
radioactive wireline logs, and of results
of core analysis, integrated where
possible with information from
specialist studies and production data.
(I) Static Model
180

Static Model
3. Lithological modeling
Definition of the lithological types
(basic facies ), which are characterized
on the basis of lithology,
sedimentology, and petrophysics. This
classification into facies is a
convenient way of representing the
geological characteristics of a
reservoir, especially for the purposes of
subsequent three-dimensional
modeling.
(I) Static Model
181

Static Model
4. Petrophysical modeling
A quantitative interpretation of well logs
to determine some of the main
petrophysical characteristics of the
reservoir rock, (porosity, water
saturation, and permeability). Core
data represent the essential basis for
the calibration of interpretative
processes.
(I) Static Model
182

Build a Petrel project of the field assembling all the data available :
1-Seismic Interpretation & Inversion
– Horizons and Fault Interpretation
2-Core Description:
– Conceptual depositional model
3- Petrophysical Interpretation
– Data review and QC
– Cementation factor (m), and Saturation exponent (n)
– Permeability-Porosity Transform
– Rock Typing (MICP, RCA, Log Data, Lithofacies)
– Free Water Level and Saturation Height Function
(I) Static Model
183

Continue Build a Petrel project of the field assembling all the data
available :
4-Structural modeling
– Fault model, Pillar gridding, Horizon model, Zonation and Layering
5-Facies Modeling
–Population of lithofacies and depositional facies in the 3D Grid
6-Petrophysical Property Modeling
– Realistic property model reflecting the reservoir geological and production
characteristics.
– Stochastic porosity and permeability modeling
– Water saturation modeling
7-Volumetrics Estimation
(I) Static Model
184

Uncertainty Analysis Workflow
186

Uncertainty Analysis Workflow
187

(II) Dynamic Model
Fully Integrated Petrel Framework
1-Entire model will be based on Petrel
– PVT, SCAL, VFP, Aquifers, Development
Strategies
2-Petrel workflows and macros will be used to
ensure a portable and maintainable history
matched model.
3-Grid block-independent multipliers will be used:
Zones, Segments, polygones, …This enables a
smooth transition from one grid size to another in
thehistory matching process
189

1-Upscaling
(II) Dynamic Model
190

1-Upscaling
1-Honoring reservoirs heterogeneity
– Retain as much geological details as possible
2-Two Upscaled models:
– High Resolution: Targeted studies (infill drilling, EOR, …)
– Low Resolution: Multi-scenario production forecasts.
– History Matching will take place on the low resolution model first
– Results will then feed into the HM of the high resolution model
3-Understand the continuity of the reservoir properties both areally and vertically
(facies)
4-Preserve vertical barriers
5- HCPV maps per zone and porosity cross-sections were made. The final
proposed layering scheme is selected giving priority to zones with high HCPV
and
high vertical contrast of porosity.
(II) Dynamic Model
191

Up scaling – QC
1. Check Volumetrics (see separate slide)
2. For all wells compare synthetic porosity, permeability and saturation logs
(fine scale and upscaled models).
3. Perform visual checks on the upscaled porosity and permeability by
comparing 2D map views, 2D cross-sections for the upscaled model and
the static model for all relevant zones.
4. Compare histograms and k-phi cross-plots before and after upscaling for
all the relevant horizons and facies
5. Compare dynamic behavior on a sector model between fine scale and
upscaled models
(II) Dynamic Model
192

2-Reservoir simulation
Reservoir simulation is a branch of petroleum engineering developed for
predicting reservoir performance using computer programs that through
sophisticated algorithms numerically solve the equations governing the complex
physical processes occurring during the production of an oil/gas reservoir.
Basically, a reservoir simulation study involves five steps:
1. Setting objectives
2. Selecting the model and approach
3. Gathering, collecting and preparing the input data
4. Planning the computer runs, in terms of history matching and/or performance
prediction
5. Analyzing, interpreting and reporting the results.
(II) Dynamic Model
193

3-History Matching
1. Uncertainty Analysis: Identify the set of reservoirs parameters with high
uncertainty and their corresponding
2. ranges of uncertainty.
3. Run a sensitivity analysis to investigate the impact of different parameters on
the flow performance (rates, water breakthrough, WCT, GOR, pressure).
4. Narrow down the set of uncertainty parameters to be carried on to be used in
the history matching process.
5. Field, Group & Well level.
6. Production data analysis helps on setting the HM criteria.
7. Calibrate model to well test data.
8. Check quality of the HM using the RST/PNL Data.
9. Potential usage of assisted history matching as applicable (Petrel HM &
Optimization or MEPO).
10. History match the Low Resolution model followed my HM of the High
Resolution model.
(II) Dynamic Model
194

❑ Breaks Down Barriers between Disciplines.
❑ Bring the Engineering Models Closer to the Operational World.
❑ Feasibility Validation of Field Development Plans.
❑ Evaluation of any Possible Production System Bottleneck.
❑ Optimizing CAPEX and OPEX
(III) Integrated Asset Model – Surface/Subsurface
195

Network Modeling including :
❑ Well/Network Modeling
❑ Well Design and Analysis
❑ Nodal Analysis
❑ Network Debottlenecking
❑ Pipeline & Equipment Sizing
❑ Gas Lift / ESP Optimization
❑ Flow Assurance
❑ Erosion & Corrosion Modeling
❑ Slug flow prediction / Slug
catcher sizing
❑ Field Network Development
Planning
(V) Network Modeling
196

Reference
1. Reservoir Engineering Handbook, (Tarek Ahmed, 5th edition)
2. integrated Reservoir Asset Management. Principles and Best Practices (John R. Fanchi)
3. Basic of reservoir engineering (Rene Cosse)
4. Fundamentals of Applied Reservoir Engineering-Appraisal, Economics-and Optimization
(RICHARD WHEATON)
5. Fundamentals of Reservoir Engineering (L.P. Dake)
6. Reservoir Engineering (Heriot-Watt University)
7. Reservoir Surveillance-(Jitendra Kikani)
8. Reservoir Engineering- the fundamental -simulation and management (Abdus Satter & Ghulam M.
Iqbal)
9. Basic Petroleum Geology and Log Analysis – (Hallibuton)
10. Basic Rock and Fluid Properties
11. Larry W . Lake -Petroleum engineering handbook - reservoir engineering and petro-physics
volume V
12. Reservoir Engineering (Kaiser A. Jasim 2019)- presentation
13. method OOIP calculation( paper )
14. Reservoir Management (Dr. Jawad R. Rustum Al-Assal)
15. static and dynamic model – work-folw (Kassem Ghorayeb) from SLB
197

198
Name: Abbas Radhi Abbas
Position: Chief Engineer / petroleum Engineer
Nationality: Iraq- Missan
Date of Birth: 1978
Gender: Male
Education Background:
Period Education description
1996-2001 University of Bagdad – college of Engineering – petroleum engineering department- (BSc)
Certificates of Appreciation
15 Certificates of Appreciation from difrent international companies such as (Schlumberger- waetherford , CNOOC , COSL ,
BHDC )
Work Experience : in Missan Oil Company ( MOC)
Period Work description
(2004-2006) reservoir engineer
(2006-2010 ) water injection engineer
during (2011) drilling and workover engineer
(2011 to 2020 ) petrophysics manager in Reservoir department
Language:
Mother language:
Arabic
Second
language/level: English/Fluent oral and written in English.
About Authorized

part 1 .pdf.pdf

More Related Content

What's hot (20)

Similar to part 1 .pdf.pdf (20)

More from MohanadHussien2 (20)

Recently uploaded (20)

part 1 .pdf.pdf