Pecker salencon

Ground reinforcement in seismic areas
J. SALENÇON * , A. PECKER **
Keywords: Shallow foundation, ground reinforcement, seismic bearing capacity
ABSTRACT: The yield design theory presents a rational tool for the evaluation of the seismic
bearing capacity of shallow foundations. It has been successfully implemented and tested against
case histories for foundation on unreinforced soil. This theoretical framework is extended to an in-
novative foundation design concept in seismic areas. This concept based on the reinforcement of
the in-situ soil with stiff, closely spaced inclusions, is economic, easy to implement and significant-
ly improves the seismic bearing capacity of the foundation. In addition, but not the least, this con-
cept introduces a capacity design philosophy in foundation engineering. Numerical studies and
centrifuge model tests have demonstrated the validity of the concept and of the theoretical tools.
1 INTRODUCTION
Following the 1985 Michoacan Guerrero earthquake and the foundation failures reported in Mexico
City, a significant amount of work has been devoted to the evaluation of the foundation bearing ca-
pacity under earthquake loading. Although restricted to shallow foundations, these studies
represent a significant improvement on the previous situation, clarifying some of the key aspects,
such as relative contribution of the inclination and eccentricity of the structural loads on the one
hand, and of the inertia forces within the soil, on the other hand.
The general theoretical framework for the evaluation of the seismic bearing capacity has been
set forth in these studies (Pecker, Salençon, 1991; Salençon, Pecker, 1995a et b; Pecker et al., 1996;
Auvinet et al., 1996; Paolucci, Pecker, 1997a, b) introducing the concept of a bounding surface in
the loading parameters space to define the set of allowable loads, recognizing the limitations of a
pseudo-static approach and developing a methodology to compute the permanent, irreversible dis-
placements. These results have been validated by comparison with observed foundations behaviors
during earthquakes, experimental results on model tests and numerical sophisticated finite element
analyses.
These theoretical tools are the basis of the analysis of a new, innovative at least in seismic areas,
design concept implemented to improve the seismic bearing capacity of a shallow foundation
(Pecker & Salençon 1998). This scheme which is presently being implemented for the foundations
of the Rion Antirion bridge in Greece (Pecker & Teyssandier 1998), aside from improving the
bearing capacity, introduces the capacity design philosophy in foundation engineering.
* Professor, Ecole Polytechnique, Palaiseau, France
** Chairman and Managing Director GEODYNAMIQUE ET STRUCTURE, Bagneux, France.

2 GENERAL FRAMEWORK FOR THE EVALUATION OF THE FOUNDATION BEARING
CAPACITY
The dynamic bearing capacity of foundations can be examined from two different approaches:
- The probably most rigorous approach would be to develop a global model (finite element
model) including both the soil and the structure. Obviously, if the analysis is meant to be signifi-
cant, a realistic non-linear constitutive soil model must be used and initial stresses need to be cor-
rectly estimated. Owing to this constraint, to computer limitations and also to the fact that devel-
opment of a global model requires competence in geotechnical engineering, structural engineering,
soil-structure interaction and numerical analysis, such an approach is seldom used in every day
practice. In addition, it is not well-suited for the development of design which requires that various
alternatives be tested before achieving a final design.
- The alternative approach, which represents the state of practice, is to uncouple the evaluation
of dynamic loads (a structural engineer task) from the verification of the bearing capacity (a geo-
technical engineer task). This is a so-called substructure approach, which suffers the following li-
mitations, which, up to now, have not clearly been evaluated:
. the evaluation of the dynamic loads is based on an elastic analysis of the soil-structure system;
at most, some degrees of non-linearities can be accounted for in an approximate manner, but how
the dynamic loads are affected by yielding of the foundation is usually not evaluated. Recently,
Paolucci (1997) has shown that the base shear transmitted by the supertructure may differ from that
predicted from a classical linear elastic soil-structure interaction analysis, if soil yielding is ac-
counted for;
. the bearing capacity is checked using a pseudo-static approach, in which only the maximum
loads acting on the foundations are considered.
This is clearly the approach which is favored in aseismic design building codes, like Eurocode 8
- Part 5, which states that "the bearing capacity of the foundation should be calculated using appro-
priate graphs and formulae which include the load inclination and eccentricity arising from the in-
ertia forces of the structures as well as the possible effects of the inertia forces in the supporting
soil itself". It is further required that the design action Sd be smaller than or equal to the design
strength:
Sd ≤ Rd (1)
In the preceding equation, the design action must be interpreted as any combination of the de-
sign vertical force Nd, horizontal force Td, overturning moment Md (and possibly inertia forces in
the soil mass):
Sd = F (Nd , Td , Md) (2)
and the design strength as the bearing capacity equation:
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛
γ
φ
γ
ψ= L,B,
tan
,
C
R
mm
d (3)
where C and φ are the soil cohesion and friction angle, γm a material partial safety factor and B,
L the foundation dimensions.
Equation (1) explicitly requires that at any time, the design action be smaller than the design
strength and precludes the possibility of having the available resistance of the soil-foundation sys-
tem being exceeded for short periods of time.
As pointed out by Newmark (1965) in his classical work on the seismic stability of earth dams,
short periods of exceedance of the available resistance are not associated with a general failure but
are accompanied by the development of permanent, irreversible displacements. This philosophy

has been successfully applied to the seismic design of earth dams and gravity retaining walls and
should be extended to shallow foundations.
It could be incorporated in code-like format simply through a slight modification of equation (1)
F (Nd , Td, Md) ≤ ⎟⎟
⎠
⎞
⎜⎜
⎝
⎛
γ
φ
γ
ψ
γ
L,B,
tan
,
C1
mmc
(4)
where γc is a partial "safety" factor which can take values greater than 1.0 to allow for small ex-
ceedance of the available resistance. Clearly, the value of γc depends on the failure mode of the
structure, on its consequences with regards to the overall behavior and on the soil behavior, wheth-
er it exhibits a post peak softening or a ductile behavior.
2.1 Determination of the equation for the bounding surface
The yield design theory (Salençon 1983, 1990), which belongs to the category of limit analysis me-
thods, constitutes the appropriate theoretical framework for the evaluation of the system available
resistance through equation (1). Alike any limit analysis method, the derivation of upper and lower
bound solutions allows to bracket the exact solution and, possibly, to determine it exactly when
both bounds coincide. In the following, only the kinematic approach is used to derive an upper
bound estimation of the bearing capacity; for the validity of the derived solution, one can refer to
either Salençon & Pecker (1995a, b) or to Ukrichton et al. (1998).
The kinematic approach of the yield design theory states that, for any virtual, kinematically ad-
missible, velocity field U, the following inequality holds:
Pe (U) ≤ Pm (U) (5)
where Pe is the work of the external forces (N, T, M) and Pm the maximum resisting work of the
system which only depends on the system strengths and geometry.
Equation (5) is similar to equation (1) and constitutes the theoretical background for limit state
design calculations (Salençon 1992). Consideration of different kinematic mechanisms, like those
presented in figure 1 for a cohesive soil, allows the right hand side of inequality (5) to be mini-
mized and the system resistance to be approximated (by excess).
Once the best approximation is obtained, inequality (5) defines a surface, called the bounding
surface, which delimits the set of allowable loads for the system: any combination (M, N, T) fall-
ing inside the surface is a stable state of forces, whereas those combinations falling outside cannot
be withstood by the system.
Without uplift With uplift
Figure 1. Kinematic mechanisms - Cohesive soil.

Figure 2 presents a three-dimensional view of the bounding surface determined for a cohesive soil
without tensile strength; only the upper part corresponding to M ≥ 0 is presented in figure 2.
Figure 2. Skeletal view of the bounding surface for a cohesive soil without tensile strength.
Simplified analytical formulae are available to define the bounding surface for a cohesive or a co-
hesionless soil (Pecker 1997). It is worth noting that experimental evidence of the existence of a
bounding surface has been given by Butterfield & Gottardi (1994) and Kitazume & Terashi (1994).
2.2 Determination of permanent displacements
One possibility which is offered by the theory, to propose tentative values for the "safety factor" γc
in equation (4), is the computations of permanent displacements which take place once the bound-
ing surface is reached. The soil foundation system is assumed to behave as a rigid perfectly plastic
system, for which the bounding surface defined previously is adopted as the boundary for the appa-
rition of plastic deformations.
This method is an extension of Newmark's original rigid blocks method to deformable bodies.
It has been successfully applied to actual case histories of foundation failure (Auvinet et al. 1996;
Pecker et al. 1995).
Under the assumptions spelled above, this method permits a rigorous definition of failure in
terms of unacceptable permanent displacements.
3 NEW CONCEPTS IN FOUNDATION ENGINEERING
Although the concepts introduced in the previous paragraph lead to a more rational approach of the
seismic bearing capacity of foundations and often result in a significant cost saving of the design,
the bearing capacity of foundations may still be of concern in difficult environmental conditions
characterized by poor soil conditions and high seismic intensities.
Under such circumstances, alternative foundation designs must be investigated and their relative
merits, in terms of economy, feasibility and technical soundness, must be weighted before a final
choice is made. When shallow foundations prove to be unsatisfactory or inadequate, a classical al-
ternative is to resort to piled foundations, although piled foundation failures during or after earth-
quakes have also been reported.
The general framework outlined in the previous paragraph may however be used to design shal-
low foundations in such a way that:
- permanent displacements are allowed,
- the development of these permanent displacements do not impede a proper functioning of the
structure; this can be achieved by a careful control on the failure mode.

To illustrate these possibilities, the theory is applied to a new concept in foundation engineering
(Pecker & Salençon 1998), which, to the best of the authors' knowledge, has never been proposed
or implemented before in seismic areas. This concept is presently being designed and implemented
for a large bridge structure in Greece, the Rion Antirion bridge (Pecker & Teyssandier 1998).
It consists of reinforcing the existing soil strata with stiff inclusions at a close spacing and to lay
a shallow foundation on top of the reinforced soil through a transition, gravel layer.
For illustration purposes, figure 3 presents an example of this concept: the foundation is a grav-
ity caisson, 90 m in diameter, and the inclusions consist of steel hollow cylinders, 2 m in diameter,
20 mm thick and 25 m long, spaced at as a square grid of 7 m x 7 m below and outside the footprint
of the foundation.
Figure 3. View of a reinforced soil foundation (Dumez-GTM).
Although the foundation looks like a piled foundation, it does not at all behave as such: no connec-
tion exists between the inclusions and the raft, thereby allowing for the foundation to uplift or to
slide with respect to the soil; the density of inclusions is far more important and the length smaller
than usually employed in piled foundations.
Aside the merits of its simplicity and economy, this technique allows for the implementation of
a seismic design philosophy very similar to the capacity design principles used in structural engi-
neering.
3.1 Theoretical analysis of a reinforced soil
The yield design theory which has been used for the evaluation of the bearing capacity on an un-
reinforced soil can be extended to account for the presence of inclusions or nails (de Buhan & Sa-
lençon 1993). A mixed modeling approach is used for the reinforced soil in which the soil is mod-
eled as a 2D continuum and the inclusions as beams. The kinematic mechanisms shown in figure 1
have been adopted to account for the presence of inclusions (Pecker, Salençon, 1998).
The contributions of all the inclusions to the maximum resisting work Pm(U) in equation (5) are
added to the maximum resisting work of the soil (right hand side of equation [5]) and minimization
is performed on the geometric parameters defining the mechanisms to find the best upper bound.

These calculations can easily be programmed on a PC; numerical minimization on the five
geometric parameters defining the kinematic mechanisms is efficiently performed with a downhill
simplex method (Nelder & Mead 1965).
3.2 Example of application
Let us take for illustration purposes the example presented in figure 3. The soil profile below the
foundation consists of a clay layer with a shear strength increasing linearly with depth:
Su = 35 + 2.8 z (6)
where Su is expressed in kPa and z is the depth below the ground surface in m. The normal
force acting on the foundation (dead weight) is equal to 860 MN, corresponding to a vertical stress
of 135 kPa.
Without the inclusions, the cross-section of the bounding surface by the plane N = 860 MN is
shown as a dotted line in figure 4 in the lower left corner.
Figure 4. Bounding surface for a reinforced soil.
If the reinforced scheme described in the previous paragraph is implemented, the bounding surface
is considerably expanded, as represented by the soil line. The maximum allowable horizontal shear
force, corresponding to the vertical ascending line to the right of the figure is associated to horizon-
tal sliding at the soil - foundation interface; this sliding occurs in the transition gravel layer placed
on top of the inclusion:
T = N tan φ = 860 tan 40° = 721 MN (7)
If one moves on the bounding surface from the point (M = 0, T = 721 MN), sliding at the inter-
face does occur until the overturning moment reaches a value of 15 000 MN.m; for higher over-
turning moments, rotational mechanisms prevail and the maximum allowable horizontal force de-
creases.
3.3 Experimental and numerical validation of the concept
The concept and theoretical evaluations presented above have been validated with model tests per-
formed in a centrifuge (Garnier, Pecker, 1999) and with non-linear finite element analyses.
0
5000
10000
15000
20000
25000
30000
35000
0 100 200 300 400 500 600 700 800 900 1000
Horizontal shear force at foundation level (MN)
Overturningmoment(MN-m)
With inclusions Without inclusions Without sliding interface

3.3.1 Numerical analyses
Non-linear finite element analyses using the computer code DYNAFLOW (Prevost 1981) have
been run under monotonic increasing loads up to failure. An elastoplastic Von Mises constitutive
model, with kinematic hardening, for the clay and a Mohr Coulomb model for the ballast layer,
have been used. Special contact elements with a limited shear capacity and no tensile strength
connect the raft and the inclusions to the soil. All the runs confirmed, within ± 10%, the limit loads
computed from the limit analyses.
In addition, the failure mechanisms found in the finite element analyses are alike the kinematic
mechanisms of figure 1.
3.3.2 Centrifuge model tests
This totally innovative concept clearly calls for experimental validation. As sophisticated as they
can be, the theoretical and numerical tools do not have the capability of modeling all the details of
the behavior of this complex scheme during an earthquake. Centrifuge model tests were therefore
undertaken with a threefold objective:
- to validate the theoretical predictions of the ultimate bearing capacity of the foundation under
monotonically increasing shear force and overturning moment;
- to identify the failure mechanism of the foundation under these combined loads;
- to assess the behavior of the foundation under various cyclic load paths.
All the tests have been carried out at 100 g on models at a scale of 1/100 of a prototype founda-
tion; the footing diameter is 0.30 m, the inclusions lengths 8.5 cm and their diameters 6.7 mm.
The soil material has been sampled on site, at the location of the bridge and reconsolidated in
the container (0.90 m in diameter).
The models are instrumented to measure:
- pore pressure at different locations below the foundation,
- soil settlements
- applied loads (shear force and overturning moment)
- bending moments in the inclusions.
The soil properties were measured in flight (at 100 g) with a cone penetrometer actuator.
Two series of tests have been run:
- the first one is intended to check the validity of the theory for monotonic loads; therefore,
tests set up departing, even significantly from the foreseen one, have been investigated;
- the second one is intended to check the behavior of the proposed reinforcement scheme under
cyclic loads. The typical load paths are shown in figure 5.
Figure 5. Typical load path
DO
Overturning moment M
Shear force T
A
K
B
C
K’

For either the three tests carried out in Nantes or for the five tests carried out in Bordeaux in
another centrifuge facility, figure 6 presents the comparison between the computed failure loads
(yield design theory) and the measured ones. In Nantes, the failure loads (triangles in figure 6),
were measured after cyclic loading, whereas in Bordeaux (diamonds in figure 6), they were meas-
ured without prior cyclic loads. Figure 6 shows that the trends are correctly predicted and that a
very good agreement is achieved for the tests in Nantes, and that failure loads are undestimated for
the tests in Bordeaux, due to significant changes in the initial geometry of the system towards the
end of the test (soil bulging in front of the model).
Figure 6. Comparison between measured and computed ultimate loads.
If the "failure loads" are taken at the start of the changes in geometry, the agreement between pre-
dictions and measurements is also very good.
Finally, the cyclic tests have shown that the system exhibits a significant energy dissipation ca-
pacity with the formation of fat hysteresis loops during cyclic loading. The equivalent damping ra-
tio computed from the hysteresis loops of figure 7 is equal to 18%, whereas the theoretical predic-
tions from the finite element analyses are of the order of 15% at the same load level.
In addition, even at very high cyclic load levels (75% to 80% of the failure load), the system
exhibits very small degradation; the hysteresis loops stabilize after a few number of cycles (fig-
ure 7); the permanent excess pore pressure is only a small fraction (30%) of the initial hydrostatic
pressure.
Figure 7. Horizontal displacement of the foundation vs. cyclic shear force T.
0
20
40
60
80
100
120
0 20 40 60 80 100 120
Measured failure load (MN)
Computedfailureload(MN)
-0.02 -0.01 0.00 0.01 0.02 0.03 0.04
Horizontal displacement (meter)
-18
-16
-14
-12
-8
-6
-4
-2
2
4
6
8
12
14
16
18
-20
-10
0
10
20
ShearforceT(MN)
Pull
Push

4 CAPACITY DESIGN PHILOSOPHY IN FOUNDATION ENGINEERING
The capacity design philosophy used in structural engineering consists in establishing a suitable
strength hierarchy between the components of the system (Paulay 1993). The structural system is
rationally and deterministically chosen so as to be able to mobilize energy dissipating regions
which will have ample reserve deformation capacity to accommodate significant departures from
the initial estimates. Paulay notes that "the strategy invites the designer to tell the structure where
plastic hinges are desirable or convenient and practicable at the ultimate limit state and to proscribe
plastification in other regions".
Clearly, this statement is relevant to the proposed reinforcement concept (Pecker, 1998).
Referring to figure 4, aside from significantly improving the resisting capacity of the founda-
tion, the reinforcement concept enforces this design philosophy:
- without reinforcement, the maximum horizontal force corresponding to a sliding at the gra-
vel - clay interface, decreases from the beginning for increasing overturning moments; this de-
crease becomes more significant for overturning moments larger than 7 000 MN.m and the failure
mechanism involves rotation of the foundation from the very beginning;
- with reinforcement, pure sliding prevails over a large range of overturning moments (up to
15 000 MN.m in that case, more than twice the previous value). In addition, would the interface
have a large strength capacity, the vertical line at 720 MN would move to the right and the bound-
ing surface would be represented by the dashed line joining the horizontal axis at 900 MN; in such
a case, the domain of the allowable forces is extended, but as soon as the bounding surface is
reached, failure modes involve a foundation rotation.
Therefore, the effect of the combined gravel layer and soil reinforcement is to improve the bear-
ing capacity, but moreover, to enforce and control the failure mode:
- the fuse provided by the gravel layer (which is a well-controlled material) plays the role of the
energy dissipating region: it limits the maximum shear force at the interface, dissipates energy by
sliding and forces the foundation "to fail" according to a failure mode which is not detrimental to
its overall behavior,
- the reinforcement increases the strength capacity with respect to undesirable failure modes,
like rotational failure modes especially for tall structures. In addition, it provides an efficient
means of dissipating energy, as evidenced by the results of cyclic centrifuge tests.
This increase in the foundation bearing capacity and the shape of the bounding surface is a func-
tion of the reinforcement scheme. Therefore, with a proper choice of the inclusions strength, spac-
ing and length, the capacity design principle described above can be enforced for a wide range of
load-moment combinations.
5 CONCLUSIONS
Based on the yield design theory, a rational approach to the evaluation of the seismic bearing ca-
pacity of shallow foundations has been developed. This approach accounts for the essential fea-
tures of the problem: the loading parameters (N, T, M and soil inertia forces) are treated as inde-
pendent parameters, leaving to the designer the choice of the most approximate combination of
them; failure is no longer defined with reference to a pseudo-static safety factor, and a methodolo-
gy to compute the permanent displacements has been derived and tested against case histories.
This approach has been extended to a new design concept for foundation engineering in seismic
areas. This concept based on an in-situ reinforcement of the existing soil with stiff, closely spaced,
inclusions overlaid by a well-controlled gravel layer allows for the use of shallow foundations,
even in difficult environmental conditions (poor soil conditions, high level of seismicity). Even
more important is the fact that this foundation concept enforces a capacity design philosophy in
foundation engineering. It looks therefore very promising for increasing the safety of the structures
and presents the advantage of being simple and rather economical.

6 REFERENCES
Auvinet, G., Pecker A., Salençon J. 1996. Seismic bearing capacity of shallow foundations in Mexico city
during the 1985 Michoacan earthquake. Proc. 11th World Conference on Earthquake Engineering, Acapul-
co, paper n° 1966.
Budhu, M., Al-Karni, A. 1993. Seismic bearing capacity of soils. Geotechnique, 33, pp. 181-187.
de Buhan P. Salençon J. 1993. A comprehensive stability analysis of soil nailed structures - European
Journal of Mechanics A/Solids, 12, n° 3, pp. 325-345.
Butterfield R., Gottardi G. 1994. A complete three-dimensional failure envelope for shallow footings on
sands. Geotechnique, vol. 44, n° 1, pp. 181-184.
Garnier J., Pecker A. 1999. Use of Centrifuge Tests for the Validation of Innovative Concepts in Founda-
tion Engineering. Proceedings 2nd
International Conference on Soil Dynamics and Geotechnical Engineer-
ing, Lisbon.
Kitazume M., Terashi M. 1994. Operation of PHRI Geotechnical Centrifuge from 1980 to 1994. Tech-
nical note of the Port and Harbour Research Institute, Ministry of Transport, Japan.
Nelder J.A., Mead R. 1965. Minimization in multidimensions with a downhill simplex method - Com-
puter Journal, vol. 7, pp. 308-310.
Newmark N. 1965. Effect of earthquakes on dams and embankments - Geotechnique, vol. 15, n° 2, pp.
139-160.
Paolucci R. 1997. Simplified evaluation of earthquake induced permanent displacements of shallow
foundations. Journal of Earthquake Engineering, vol. 1, n° 3, July 1997, pp. 563-579.
Paolucci R., Pecker A. 1997. Soil inertia effects on the bearing capacity of rectangular foundations on co-
hesive soils. Engineering Structures, vol. 19, n° 8, Elsevier Science Ltd., pp. 637-643.
Paolucci R., Pecker A. 1997. Seismic bearing capacity of shallow strip foundations on dry soils - Soils
and Foundations, vol. 37, n° 3, pp. 95-105.
Paulay T. 1993. Simplicity and Confidence in Seismic Design - The Fourth Mallet-Milne Lecture, J. Wi-
ley.
Pecker A. 1998. Capacity Design Principles for Shallow Foundations in Seismic Areas. Keynote lecture
XIth European Conference on Earthquake Engineering, September 1998, Paris.
Pecker A., Salençon J. 1991. Seismic bearing capacity of shallow strip foundations on clay soils. CE-
NAPRED - Proceedings of the International Workshop on Seismology and Earthquake Engineering, Mexico,
pp. 287-304.
Pecker A., Auvinet G., Salençon J., Romo, M.P., Verzura L. 1995. Seismic bearing capacity of founda-
tions on soft soils. Report to the European Commission. Contract CI1* CT92-0069.
Pecker A. 1997. Analytical formulae for the seismic bearing capacity of shallow strip foundations. Seis-
mic Behavior of Ground and Geotechnical Structures, 1997, Seco e Pinto Editor. Balkema.
Pecker A., Salençon J. 1998. Innovative concepts in foundation Engineering. Proceedings of the 2nd
Ja-
pan-UK Workshop on Implications of Recent Earthquakes. Technical report TIT/EERG 98-6. April 1998.
Pecker A., Teyssandier J.P. 1998. Seismic design for the foundations of the Rion-Antirion Bridge. Proc.
Institution of Civil Engineers, Geotechnical Engineering, 131, pp. 4-11, paper n° 11311.
Prevost J.H. 1981. DYNAFLOW - A finite element analysis program for the static and transient response
of linear and non linear two and three-dimensional systems" - Department of Civil Engineering - Princeton
University.
Richards R., Elms, D.G., Budhu, M. 1993. Seismic bearing capacity and settlements of shallow founda-
tions. ASCE Journal of Geotechnical Engineering, 119, pp. 662-674.
Salençon J. 1983. Calcul à la rupture et analyse limite. Presses de l'Ecole Nationale des Ponts et
Chaussées.
Salençon J. 1990. Introduction to the yield design theory. European Journal of Mechanics A/Solids 9,
n° 5, pp. 477-500.
Salençon J. 1992. Approche théorique du calcul aux états limites ultimes. Les Grands Systèmes des
Sciences et de la Technologie. Masson.
Salençon J., Pecker A. 1995. Ultimate bearing capacity of shallow foundations under inclined and eccen-
tric loads. Part I: purely cohesive soil. European Journal of Mechanics A/Solids, 14, n° 3, pp. 349-375.
Salençon J., Pecker A. 1995. Ultimate bearing capacity of shallow foundations under inclined and eccen-
tric loads. Part II: purely cohesive soil without tensile strength. European Journal of Mechanics A/Solids,
14, n° 3, pp. 377-396.
Sarma S.K., Iossifelis I.S. 1990. Seismic bearing capacity factors of shallow strip footings. Geotechnique,
40, pp. 265-273.

Ukrichton B., Whittle A.J., Sloan S.W. 1998. Undrained Limit Analyses for Combined Loading of Strip
Footings on Clay - Journal of Geotech. and Geoenvir. Engineering, vol. 124, n° 3.

Pecker salencon

More Related Content

What's hot (20)

Viewers also liked (19)

Similar to Pecker salencon (20)

More from gefyra-rion (20)

Recently uploaded (20)

Pecker salencon