Statnamic testing of soils
Download as PPT, PDF4 likes3,022 views
The document discusses Statnamic testing for piles. Statnamic testing loads piles using controlled explosions that induce stress waves into the pile over 120 milliseconds, allowing the pile and soil to be loaded together. It is faster and less expensive than static pile load testing. Statnamic testing can test piles, pile groups, and other deep foundations up to loads of 30 MN. It provides immediate load-displacement results on site.
Statnamic testing of soils
- 1. “Statnamic Testing For Piles” Sravan M V 1BM03CV049
- 2. Introduction Why Pile Testing?
- 3. Types of Testing for Piles Static Testing Dynamic Testing Statnamic Testing
- 4. Static Pile Load Test Velocity and acceleration are near zero. For quick static load test results can vary. Damping and inertial effects are minimal. Stress waves are not introduced. Time Consuming. Heavy Loads are required.
- 5. Static Pile load test pics…
- 6. Static Pile load test pics…
- 7. Stress Wave Mechanics In conventional static loading, the pile compresses as a whole throughout loading such that the pile is in compression. However, as the load duration decreases, stress waves are introduced to the pile which effect pile/soil behavior. Stress waves propagate along the pile at the speed of sound within the pile c = stress wave velocity Is 6 milliseconds, the natural pile period.
- 8. Dynamic Pile Load test Time taken is around 5-10 ms Stress Waves are induced which affects the pile/soil behavior Damping and inertial effects exert a strong influence on the test result and are more difficult to quantify. Cause tensile stresses in piles, damage them. Very expensive.
- 9. Dynamic Load Test Pics..
- 10. Statnamic Test : HISTORY STATNAMIC development began in 1988 with a 0.1 MN test device.Today, test devices are capable of producing loads up to 30 MN.
- 11. Statnamic Test : Stats STATNAMIC load tests have been conducted in Canada, the United States, the Netherlands, Japan, Germany, Israel, Korea, Taiwan, United Arab Emirates, Egypt, United Kingdom, Malaysia, Indonesia, Australia, China, Belgium, Hungary, Grenada, Argentina. Testing options include single piles, pile groups, structural elements, bridge piers, spread footings and plates.
- 12. Statnamic Test : Stats STATNAMIC can be used on any pile type or structure: micro piles piles batter piles lateral load tests pile groups bridge piers caissons spread footings
- 13. Statnamic Test : Procedure STATNAMIC assembly is straightforward. All components are handled with a hoisting machine. Reaction masses are and made of concrete, lead, steel, gravel, water etc. Concrete reaction masses can be cast on-site and reused.
- 14. Statnamic Test : Procedure The STATNAMIC device is placed directly atop the test pile. Solid fuel is burned within a pressure chamber, creating a large pressure which drives the reaction mass upward. An equal and opposite force pushes downward on the pile. If a reaction mass of 30,000 Kg is accelerated upward at 20 g, then a resultant 6 MN force acts downward on the foundation.
- 15. Statnamic Test : Procedure STATNAMIC loading is applied in a gradually increasing manner and unloading is achieved by a controlled venting of the pressure. The total duration of force is on the order of 120 milliseconds. Typical STATNAMIC pile accelerations of 1-3 g are 100– 1000 times less than a conventional dynamic load test.
- 16. Statnamic Test : Procedure Loading increases to a maximum before unloading by a controlled venting of the pressure. Built-in instrumentation (load cell and laser sensor) record load and displacement during the entire STATNAMIC test.
- 17. Statnamic Test : Advantages STATNAMIC applies loads up to 30 MN (3,400 tons). STATNAMIC can test bridge foundations, pile groups, spread footings, and off-shore piles. STATNAMIC can test the lateral capacity of foundations. Production piles can be tested without prior planning. No reaction piles are required. Three 600 ton tests can be conducted in a one day shift. Several STATNAMIC tests can be conducted for the cost of a single static test.
- 18. Statnamic Test : Advantages The duration of loading is on the order of 10 Hz. STATNAMIC 's built-in load cell and laser sensor provide direct measurements of load-displacement behavior. STATNAMIC loads the pile and soil together. STATNAMIC produces load-displacement results immediately on site.
- 19. Description W.R.T Newton Laws. 1st Law (Law of Inertia): “A body will continue in a state of rest or uniform motion unless compelled to change that state by an external force.” In a load test, two external forces act on a pile - the loading force and pile resistance.
- 20. Description W.R.T Newton Laws. 2nd Law (Law of Acceleration): “ When acted upon by an external force, a body accelerates in the direction of that external force and is proportional to the magnitude of that force.” F = ma In static, statnamic, and dynamic load testing, the same net force can be applied to a pile by different means. Compare: Static: F = M *g = Mg STAT NAMIC: F = M/20 * 20g = Mg Dynamic: F = M/500 * 500g = Mg
- 21. Description W.R.T Newton Laws. 3rd Law (Action and Reaction): “For every action there is an equal and opposite reaction.” F12 = -F21 During STATNAMIC loading, the STATNAMIC device exerts an upward force on the reaction masses, while an equal and opposite force reacts downward on the pile.
- 23. 4 MN 14 MN 30MN
- 24. CONCLUSION!! The STATNAMIC load test was developed to meet the construction industry's demand for an accurate and cost-effective method of determining the load bearing capacity of caissons and high capacity piles.
- 25. REFERENCES “SOIL MECHANICS AND FOUNDATIONS” – Dr. BC PUNMIA,Ashok Kumar Jain & Arun Kumar Jain http://www.berminghammer.com/stat.html http://www.piletest.co.uk/statnamic.html
- 26. “Your job might be only to clean a railway- crossing, but it is for you to make it so clean that no other crossing in the world is as clean as your's.” - Sir M Viswesvaraiah Thank you!