Chapter 8: Vessels Rules of Thumb for Chemical Engineers, 5th Edition by Stephen Hall
Instructions Don't overwrite the template! Before doing anything, "Save-As" this file under a new name!!
A A J L H
The worksheet is locked. Use the TAB key to move between fields. When adding revisions, first unlock the sheet. Tools-Protection-Unlock There is no password. Copy the appropriate revision triangle to the clipboard, then paste it where needed. Use Visio or another drawing program to create the vessel sketch. Paste it into the designated area; resize to fit. Right click on the graphic and choose "Format Object". Click the "Lines" tab; choose "No Line" to get rid of the border.
P I
CODE is normally ASME Sec VIII Div 1 STAMP is normally "yes" If no jacket, put "N/A" in the jacket column.
O P
Head type could be ASME Dished, 2:1 elliptical, conical, etc. Any field that is too small: put reference to note (e.g., "Note 1"); then put the information in the Notes section. Choose the most descriptive materials of construction as possible, using ASTM numbers if known. Nozzle types include: RF = raised face FF = flat face FNPT = female normal pipe thread TriClover = sanitary type clamp or refer to Note
I
ChemEng Software sells an Excel template called TANKVOL www.chemengsoftware.com TANKVOL calculates the filled volume of horizontal and vertical vessels with flat, elliptical, torispherical, F&D, conical, and guppy heads. Order on-line or by telephone, 24-h/d; credit cards accepted.
I P
PRESSURE VESSEL
CLIENT REV PREPARED BY 0 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Notes DATE APPROVAL W.O. UNIT Sketch Reference Drawing No. Manufacturer Manufacturer's Drawing No. Code AREA EQUIP. NO REQUISITION NO. PROCURED BY PAGE SPECIFICATION NO. INSTALLED BY
Stamp? Shell Jkt.
Operating Pressure, psig Design Pressure, psig Operating Temperature, deg F Design Temperature, deg F Relief Valve set pressure, psig Corrosion Allowance, in Position (horizontal/vertical) Location (indoor/outdoor) Height or Length (T-T), ft-in Inside Diameter, ft-in Head type Jacket Type Nominal Volume, gal Specific Gravity of Fluid Materials of Construction Shell Top Head Bottom Head Internals Lining Gaskets Bolts Finishes Process wetted parts Jacket wetted parts Exterior Supports Insulation Earthquake Zone Design wind speed, mph Internals Nameplate
Shell
Jkt.
Item A B C D E F G H I J K L M N O P Q R Openings Key
Number
Openings Size/Type
Service
AGITATOR
CLIENT REV PREPARED BY 0 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 DATE APPROVAL W.O. UNIT AREA EQUIP. NO REQUISITION NO. PROCURED BY PAGE SPECIFICATION NO. INSTALLED BY
leave blank - reserve for equipment name Equipment Number Position (horizontal/vertical) Location (indoor/outdoor) Height or Length (T-T), ft-in Inside Diameter, ft-in Head type Nominal Volume, gal Description of mixing requirement: Component Vessel Data Operating Pressure, psig Design Pressure, psig Operating Temperature, deg F Design Temperature, deg F Material of Construction Process Fluid Components Liq/Solid %
Operation (batch/continuous) Blending Time Heat Transfer Solids Suspension Other Mixture Properties Temperature, deg F Specific Gravity Viscosity, cP pH Solids Density, lb/cu.ft. Size Settling Rate, ft/min. Mechanical Requirements Shaft Shaft Seal Length Type Diameter Pressure Coupling Flush Fluid Steady Bearing Materials Materials Finish Mounting Flange Speed
Impeller Number Type Diameter Mounting Materials Finish Mounting Type Motor Type
Area Classification Power Horsepower
Class Volts Calculated
Electrical Requirements Group Division Phases Cycles BHP Nominal
Enclosure Frame RPM
Drive Type (direct, gear, bevel, etc.)
Notes
