LM107 LM207 LM307 Operational Amplifiers
December 1994
LM107 LM207 LM307 Operational Amplifiers
General Description
The LM107 series are complete general purpose operational amplifiers with the necessary frequency compensation built into the chip Advanced processing techniques make the input currents a factor of ten lower than industry standards like the 709 Yet they are a direct plug-in replacement for the 709 LM101A and 741 The LM107 series offers the features of the LM101A which makes its application nearly foolproof In addition the device provides better accuracy and lower noise in high impedance circuitry The low input currents also make it particularly well suited for long interval integrators or timers sample and hold circuits and low frequency waveform generators Further replacing circuits where matched transistor pairs buffer the inputs of conventional IC op amps it can give lower offset voltage and drift at a lower cost The LM107 is guaranteed over a b55 C to a 125 C temperature range the LM207 from b25 C to a 85 C and the LM307 from 0 C to a 70 C
Features
Y Y Y Y
Offset voltage 3 mV maximum over temperature Input current 100 nA maximum over temperature Offset current 20 nA maximum over temperature Guaranteed drift characteristics
Connection Diagrams
Metal Can Package Dual-in-Line Package
TL H 7757 2
Note Pin 4 connected to case
Top View Order Number LM107H 883 See NS Package Number H08C
TL H 7757 3
Top View Order Number LM107J 883 or LM207J See NS Package Number J08A Order Number LM307N See NS Package Number N08A
Dual-in-Line Package
TL H 7757 13
Order Number LM107J-14 883 See NS Package Number J14A
Available per SMD
5962-8958901
TL H 7757 RRD-B30M115 Printed in U S A
C1995 National Semiconductor Corporation
Absolute Maximum Ratings
If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications (Note 4) Supply Voltage Power Dissipation (Note 1) Differential Input Voltage Input Voltage (Note 2) Output Short Circuit Duration Operating Temperature Range (TA) (LM107) (LM207) Storage Temperature Range Lead Temperature (Soldering 10 sec) LM107 LM207 g 22V 500 mW g 30V g 15V Continuous
b 55 C to a 125 C b 25 C to a 85 C b 65 C to a 150 C
LM307 g 18V 500 mW g 30V g 15V Continuous 0 C to a 70 C
b 65 C to a 150 C
TMIN
b 55 C b 25 C
TMAX
a 125 C a 85 C a 70 C
LM107 LM207 LM307 0C ESD rating to be determined
260 C
260 C
Electrical Characteristics (Note 3)
Parameter Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Supply Current Conditions Min TA e 25 C RS s 50 kX TA e 25 C TA e 25 C TA e 25 C TA e 25 C VS e g 20V VS e g 15V TA e 25 C VS e g 15V VOUT e g 10V RL t 2 kX RS s 50 kX 30 50 15 LM107 LM207 Typ 07 15 30 40 18 30 18 160 30 15 20 25 C s TA s TMAX TMIN s TA s 25 C 0 01 0 02 01 02 100 TA e a 125 C VS e g 20V 12 25 0 01 0 02 60 25 160 10 30 70 03 06 300 30 Max 20 10 75 05 Min LM307 Typ 20 30 70 20 Max 75 50 250 mV nA nA MX mA mA V mV mV mV C nA nA C nA C nA mA Units
Large Signal Voltage Gain Input Offset Voltage Average Temperature Coefficient of Input Offset Voltage Input Offset Current Average Temperature Coefficient of Input Offset Current Input Bias Current Supply Current
Electrical Characteristics (Note 3) (Continued)
Parameter Large Signal Voltage Gain Output Voltage Swing Conditions Min VS e g 15V VOUT e g 10V RL t 2 k X VS RL RL
e g 15V e 10 kX e 2 kX
LM107 LM207 Typ Max Min 15 25
g 12 g 10 g 15 g 14 g 13 g 12 g 10
LM307 Typ Max
Units
V mV
g 14 g 13
V V V V
Input Voltage Range
VS e g 20V VS e g 15V RS s 50 kX RS s 50 kX
a 15 b 13
g 12
a 15 b 13
Common Mode Rejection Ratio Supply Voltage Rejection Ratio
80 80
96 96
70 70
90 96
dB dB
Note 1 The maximum junction temperature of the LM107 is 150 C and the LM207 LM307 is 100 C For operating at elevated temperatures devices in the H08 package must be derated based on a thermal resistance of 165 C W junction to ambient or 30 C W junction to case The thermal resistance of the dual-in-line package is 100 C W junction to ambient Note 2 For supply voltages less than g 15V the absolute maximum input voltage is equal to the supply voltage Note 3 These specifications apply for g 5V s VS s a 20V and b 55 C s TA s a 125 C for the LM107 or b 25 C s TA a 85 C for the LM207 and 0 C s TA s a 70 C and g 5V s VS s g 15V for the LM307 unless otherwise specified Note 4 Refer to RETS107X for LM107H and LM107J military specifications
Schematic Diagram
Pin connections shown are for metal can
TL H 7757 1
Guaranteed Performance Characteristics LM107
Input Voltage Range Output Swing
LM207 Voltage Gain
TL H 7757 4
Guaranteed Performance Characteristics LM307
Input Voltage Range Output Swing Voltage Gain
TL H 7757 5
Typical Performance Characteristics
Supply Current Voltage Gain Input Current
Current Limiting
Input Noise Voltage
Input Noise Current
TL H 7757 6
Typical Performance Characteristics
Open Loop Frequency Response
(Continued) Voltage Follower Pulse Response
Large Signal Frequency Response
TL H 7757 7
Typical Applications
Inverting Amplifier Non-Inverting AC Amplifier
VOUT e b RIN e R1
R2 VIN R1
VOUT e
R1 a R2 VIN R1 R2
TL H 7757 9
TL H 7757 8
RIN e R3 R3 e R1
Non-Inverting Amplifier
VOUT e
R1 a R2 VIN R1
TL H 7757 10
Pin connections shown are for metal can
Typical Applications
(Continued) Turntable Notch Filter
R1 e R2 e R3 R4 e R5 e fo e R1 2
1 2q0C1 C2 R4 R5
e 60 Hz
TL H 7757 11
Differential Input Instrumentation Amplifier
TL H 7757 12
Pin connections shown are for metal can
Physical Dimensions inches (millimeters)
Metal Can Package (H) Order Number LM107H 883 NS Package Number H08C
Physical Dimensions inches (millimeters) (Continued)
Ceramic Dual-In-Line Package (J) Order Number LM107J 883 or LM207J NS Package Number J08A
Ceramic Dual-In-Line Package (J) Order Number LM107J-14 883 NS Package Number J14A
LM107 LM207 LM307 Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
Molded Dual-In-Line Package (N) Order Number LM307N NS Package Number N08E
LIFE SUPPORT POLICY NATIONALS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user
National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018
2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness
National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80
National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960
National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408
National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.
