RTU560
ABB Utilities GmbH
Remote Terminal Unit
Data Sheet
Extension Module Rack 23ET23
Application
The extension board rack 23ET23 is designed to accept up to 19 input/output boards of a RTU560 remote terminal unit. It is interfaced to the communication rack 560CSR01 via the serial RTU560 system
bus. Up to 7 23ET23 expansion board racks can be
connected to one basic board rack.
signal wires is made by the means of crimp clips using snap-in fixings. In addition to the use of prefabricated cables it is also possible to attach individual
wires during commissioning.
DIN- -F connector with cutout
for row 22 - - 32
The extension board rack 23ET23 is installed in a
swing frame cabinet or in a frame with 19 wide supports.
Characteristics
The 19 board rack has a height of 3 HE for single
Euro-card format boards (DIN 41494). There are 21
slots available for the installation of boards.
The power supply unit (NG) has a predefined slot allocated to it.
Allocation of the Slots:
V maximum of 19 peripheral boards (19 slots)
V power supply unit (2 slots)
For the physical interfacing of boards edge connectors of type F (DIN 41612) are used. Rows 2 to 20 of
the edge connectors connect the RTU560 system
bus and are soldered directly to the printed circuit
board. The connection of the process signals is
made via the rows 22 to 32 by the means of sub- connectors. The sub- -connector clips into a cutout
in the edge connector (Fig. 1). The connection of the
Doc.- -No.: 1KGT 150 412 V000 1
Sub- -connector
Fig.1:
Sub-connector design
This interface technology minimises the number of
cable connections as well as the space required in
the expansion board rack 23ET23.
A monitoring circuit on the expansion board rack
23ET23 checks the supply voltage of the boards
(24 V DC, 5 V DC).
In addition to the process signal connections, the following interface possibilities are located on the rear
side of the printed circuit board:
V interface to the serial peripheral bus
V external power source connections
V status relay contact of monitoring the internal voltages (24 V DC and 5 V DC)
33
ABB Utilities GmbH
RTU560
Data Sheet Extension Module Rack 23ET23
Front view
560PSU01
23BE21 23BE21 23BE21 23BE21 23BE21
132,8 mm (5,2)
24 V
5V
1
2
3
4
5
6
7
8
UE +
UE -PE
ON
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0FF
482,6 mm (19)
Rear view (Backplane)
rack
ALARM RELAY
SPB
DIN
ADR
81
1
77
2
73
3
69
4
65
5
61
6
57
7
53
8
49
9
45
10
41
116
37
12
33
13
29
14
NG
25
15
21
16
17
17
13
18
9
19
5
20
cut- -out for the sub- -connector
Side view
190,5 mm (7,5)
Bus printed circuit board
rear- -side component fitting
18 pole sub- -connector
34
Doc.- -No.: 1KGT 150 412 V000 1
ABB Utilities GmbH
RTU560
Extension Module Rack 23ET23
Technical Data
In addition to the general technical data of the RTU560, the following applies:
Subrack
Dimensions:
Power source connections
19, 3 HE, 21 s DIN 41494
1 slot = 4 units = 20.32 mm
132.8 x 482.6 x 215 mm
(H x W x D)
Printed circuit board
Dimensions:
433.7 x 132.8 mm (W x H)
X14- -X17 :
plug-in terminalstrip
2- -pole each
Monitoring connection
X11,X12:
Relais contact
plug- -in terminalstrip
2- -pole each
NC- -contact
1 A / 60 V DC / 30 W
Types of Connection
Protection Earth- - / Shield terminal
Peripheral boards: indirect, 48 pole
Type F DIN 41612
with cutout for sub-connector
Environmental Conditions
Processsignal- connection:
18 pole sub-connector
with crimp clips
Serial interfaces
SPB ( X1 / X2 ):
Sub- -D connector 9-pole
male and female DIN 41652
Doc.- -No.: 1KGT 150 412 V000 1
PE / A:
Faston 6,3 mm
Temperature
0 ... 70 _C
Rel. humidity:
5 ... 95%
(non condensing)
Ordering Information
23ET23R0001
GSNE 002 400 R0001
35
ABB Utilities GmbH
Data Sheet Extension Module Rack 23ET23
ABB Utilities GmbH
Kallstadter Strae 1
68309
Mannheim (Germany)
Telephone +49 (0) 621 381- -7592
Telefax
+49 (0) 621 381- -7622
36
03/2001
RTU560
Subject to alteration
Doc.- -No.: 1KGT 150 412 V000 1
