Strainers with flanged connections
Type2NWith standard strainer insert
Type2NIWith dual strainer insert
Application
Designed to protect downstream plants, aggregates as well as
measuring and control devices against impurities Straining
and collecting dirt particles carried along by the medium.
Body in PN10 to 40DN15 to250Flanged connections
Suitable for liquids, steam, and gases up to max. 450C
The strainers consist of a Y-style body with flanged connections
and a wide-meshed filter element (standard strainer insert) or
a wide-meshed filter element with an additional fine-meshed
filter element (dual strainer insert).
Special features
Compact design with face-to-face dimensions according to
DIN
Easy removal of the collected dirt particles
Easy replacement of the strainer insert
Versions
Type2NWith standard strainer insert Fig.1: Type2N and Type2NI Strainers
Type2 NIWith dual strainer insert
Strainers with DIN flanges Principle of operation
Cast iron body for PN10 and 16, DN15 to 250 The medium flows through the strainer in the direction indicat-
ed by the arrow on the body. The uncleaned medium first
Spheroidal graphite iron body for PN16 and 25, DN15
contacts the inside of the strainer insert (filter element). While
to 150
it passes through the filter element, the dirt particles carried
Cast steel body for PN16 to 40, DN15 to 250 along by the medium are collected in the filter element. The
Cast stainless steel body for PN16 to 40, DN15 to 100 dirt particles can be removed after undoing the cover flange.
Special versions Installation Further details can be found in uEB1015.
With two threaded ports for pressure gauge connection The direction of flow must match the direction indicated by the
(DN15 to 100: G, DN125 to 250: G) arrow on the body. Leave enough space to remove the filter
Additional support cage in cases where backflow may element for cleaning (see Dimensions and weights).
occur in vertical pipelines Install strainers in vertical pipelines with the medium flow-
With threaded port for rinsing line connection (DN15: ing upward with the cover flange facing upward as indi-
G, DN20 to 250: G) cated by the arrow. In this case, dirt particles are retained
Flanges with tongue, male face or female face but not collected.
Flanges with groove according to DIN2512 Install swing check valves or similar devices to prevent
backflow.
Edition March 2016
Data Sheet T 1015 EN
Table1: Technical data
Type Valve size DN 15 20 25 32 40 50 65 80 100 125 150 200 250
KVS m/h 5 10 17.5 21 36 65 116 150 235 366 522 950 1450
Mesh size mm 0.5 0.8 1.25 2
Mesh count per cm 150 59 28 12
2N
Flow resistance
2.5
coefficient
Approx. 2.75 times pipe Approx. 2.5 times pipe cross-
Free filter area Approx. 3 times pipe cross-section
cross-section section
KVS m/h 4.5 8 14 18 29 51 90 115 190 290 450 760 1150
Mesh size mm 0.25
Mesh count per cm 625
2NI 1)
Flow resistance
3
coefficient
Approx. 2.75 times pipe Approx. 2.5 times pipe cross-
Free filter area Approx. 3 times pipe cross-section
cross-section section
1) Type2NI fulfills the requirements of DVGW (German Technical and Scientific Association for Gas and Water) according to DINEN161
The pressure loss p in bar caused by the strainer can be calculated using the following equation:
p Pressure loss bar
Flow resistance coefficient Dimensionless
p [bar] =
200000 Mean velocity in reference cross-section m/s
Density of the process medium kg/m
Pressure-temperature diagram
1.0619
p [bar]
EN-GJL-250
PN 1.4408
40 EN-GJS-400-18-LT
40
30
25
20
10 16
t
-10 0 80 100 150 200 300 350 400 450 [C]
EN-GJL-250
EN-GJS-400-18-LT
1.0619
1.4408
Fig.2: Pressure-temperature diagram
2 T 1015 EN
Dimensions and weights
X detailed views for special version with pressure gauge connection
1 Body
2 Filter
3 Gasket
4 Cover flange
Fig.3: Dimensions
Table2: Dimensions in mm and weights
Valve size DN 15 20 25 32 40 50 65 80 100 125 150 200 250
Length L 130 150 160 180 200 230 290 310 350 400 480 600 730
Height H1 45 60 70 85 95 115 150 180 224 255 290 385 480
H2 (strainer insert pulled out) 75 90 110 135 160 195 225 295 343 420 485 640 790
PN10 PN16
PN25 PN40 Spheroidal
Weight, graphite iron/ 1.9 2.8 3.3 5.4 6.5 9.1 12 17 24 36 52 91 152
approx. kg cast iron
Cast steel 2.2 3.2 4.0 5.8 7.2 10 14 19 28 42 60 130 195
Table3: MaterialsMaterial numbers according to DIN EN
Valve size DN15 to 250 DN15 to 150 DN15 to 250 DN15 to 100
Nominal pressure PN10 to 16 PN16 and 25 PN16 to 40 PN16 to 40
Cast iron Spheroidal graphite iron
Body Cast steel 1.0619 Cast stainless steel 1.4408
EN-GJL-250 EN-GJS-400-18-LT
Cover flange EN-GJL-250 1.0460 1.04601) 1.4571
Filter Stainless steel 1.4401
Seal Graphite on metal core
1) DN200 and 250: 1.0619
Ordering text
Type2N or Type2NI Strainer, nominal size DN ...,
Nominal pressure PN ..., body material ,
Optionally, special version ...
T 1015 EN 3
Specifications subject to change without notice
2017-01-10 English
SAMSON AG MESS- UND REGELTECHNIK
Weismllerstrae 3 60314 Frankfurt am Main, Germany
Phone: +49 69 4009-0 Fax: +49 69 4009-1507
samson@[Link] [Link] T 1015 EN
