1|Page
CHESO MACHINERY PTE. LTD.
Haitian MarsII(MAII)
Premium Series.
MAII3800/2250
Servo Motor Machine.
Moulding Machine Specification
Derick
4/9/2013
2|Pa g e
Machine Specification
Injection Unit
MAII3800/2250
Screw diameter mm 65
Screw L/D ratio L/D 21.5
Shot size (theoretical) cm3 1068
Injection weight (PS) g 972
Injection rate(PS) g/s 333
Injection pressure MPa 211
Plasticizing rate(PS) g/s 58.6
Screw speed rpm 0~220
Clamping Unit
Clamp tonnage kN 4700
Toggle stroke mm 780
Space between tie bars mm 820 x 800
Max. mold height mm 980mm
Min. mold height mm 320mm
Ejector stroke mm 200
Ejector force kN 110
*Due to continual improvement specification are subject to change without prior notice.
3|Pa g e
Others
Max. pump pressure MPa 16
Pump motor power kW 45
Heater power kW 28.2
Machine dimension ( l x w x h ) m 8.15 x 1.99 x 2.36
Machine weight t 17.5
Hopper capacity kg 50
Oil tank l 830
Platen dimensions moving platen for widening unit
*Due to continual improvement specification are subject to change without prior notice.
4|Page
Mounting hole for robot/sprue picker top view from fixed platen for widening unit
*Due to continual improvement specification are subject to change without prior notice.
5|Pa g e
Machine dimensions for widening unit
*Due to continual improvement specification are subject to change without prior notice.
6|Page
Standard Equipment
Clamping unit
New design compact 5 point fast, rigid toggle system.
Mechanical, electrical mold safety interlock device.
Low pressure mold protection device.
Multi stage mold open/close pressure & speed control.
Multi stage, multi function hydraulic ejection control.
Intensified wear resistant supporting tracks for movable platen.
Mold cooling water flow regulator.
1 set hydraulic core puller system (A & B).
Automatic toggle greasing system by central lubrication system.
Fast mold closing device.
Mold open/close brake circuit.
Adjustable moving platen support.
Mold height adjustment using hydraulic motor.
Reliable pre-tensioning tie bar.
Potential meter for mold open clamp & ejection.
Automatic mold height adjustments function for clamp force setting.
T-slot platen on moving & stationery platen plus T-bolt.
1 set of ejector pull back confirmation limit switch.
Air jet circuits.
*Due to continual improvement specification are subject to change without prior notice.
7|Pa g e
Injection unit
Multi stage injection phase pressure, speed, & position control.
Multi stage holding phase pressure, speed & time control.
Multi stage plasticizing pressure control, speed & position control.
Time or position control holding change over.
Injections cushioning position monitoring function.
Potential meter for injection.
Plasticizing cold start preventive function.
Purging cover.
Three modes for injection unit retraction.
Automatic purging function.
Injection unit anti-slip cover.
High torque motor for screw plasticizing.
Suck back function.
PID barrel temperature control device.
Water cooling control system for hopper throat.
Screw plasticizing back pressure control function.
Barrel heater insulation cover.
Auto start barrel heating function.
Nozzle centering alignment device.
Screw speed detection device
Bi-metallic screw & Barrel A type.
1 set of extended long nozzle.
2 set of hot runner valve gate control signal.
*Due to continual improvement specification are subject to change without prior notice.
8|Pa g e
Hydraulic
High capability servo motor with gear pump dynamical control system.
Oil temperature upper & lower limit alarm.
Oil tank level.
Oil suction filter alarm.
Oil cooler.
Electronics
Computerized KEBA 2580 system control function.
Robot interface circuit with Euromap 67 plug.
Unattended running operation lock switch.
STN color screen for graphics display with multi language selected.
Mold data storage 50 sets.
Mold condition monitoring function.
Abnormal alarm function.
Barrel temperature monitoring function.
Electric motor safety protection device.
System hardware I/O testing functions.
3 sets of auxiliary power outlet.
Emergency stop safeguard device.
Alarm light.
*Due to continual improvement specification are subject to change without prior notice.
9|Page
General
Haitian standard color green, Yellow & grey.
Adjustable machine leveling pads.
1 sets of professional tools with tool box. (Nozzle spanner).
Haitian standard material hopper 50kgs.
1 set of consumable spare parts ( O ring, Heater band, Filters )
*Due to continual improvement specification are subject to change without prior notice.
