[Link]
la
TEPO SOLE CO., LTD 020 22300188
MEMBER NAME : C01
1. General Information
(1) Design Code : ACI318-08M
(2) Unit System : N, mm
2. Material
(1) F'c : 29.42MPa
(2) Fy : 392MPa
(3) Fys : 392MPa
3. Section
300
(1) Section Size : 300 x 300mm
(2) Lx : 1.300m
(3) Ly : 1.300m
(4) Kx : 1.000
(5) Ky : 1.000
(6) Splicing Limit : 50%
30
4. Forces
(1) Pu : 537kN
(2) Mux : -116kN.m 300
(3) Muy : 0.000kN.m
(4) Vux : -281kN
(5) Vuy : 0.000kN
(6) Pux : 0.000kN
(7) Puy : 0.000kN
5. Factors
(1) Cmx : 0.850
(2) Cmy : 0.850
(3) βdns : 0.600
6. Rebar
(1) Main Bar
Layer-1 : 12-4-P20(P20) (Cc = 30.00mm, As = 3,770mm^2)
Layer-2 :-
Layer-3 :-
Layer-4 :-
[Link] : 3,770mm^2
(2) Hoop Bar
End : P10@150
Middle : P10@150
(3) Tie Bar
Apply Tie Bar to Shear Check : Yes
Tie Bar : P10 ( Fy = 392MPa )
7. Check Slenderness Ratio
(1) Calculate radii of gyration
rx = 0.3D = 90.00mm
ry = 0.3B = 90.00mm
(2) Calculate slenderness ratio
M1x
= 0.625
M2x
M1y
= 0.625
M2y
kx lux M1x
= 14.44 < 34 - 12 = 26.50 -> Not Slender
rx M2x
ky luy M1y
= 14.44 < 34 - 12 = 26.50 -> Not Slender
ry M2y
8. Check Magnified Moment
(1) Calculate moment magnification factor
δns.x = 1.000
2018-08-14 1
[Link]
TEPO SOLE CO., LTD 020 22300188
MEMBER NAME : C01
δns.y = 1.000
9. Check Minimum Moment
(1) Calculate minimum eccentricity
emin.x = 15 + 0.03D = 24.00mm
emin.y = 15 + 0.03B = 24.00mm
(2) Calculate minimum moment
Mmin.x = Pu emin.x = 12.89kN.m
Mmin.y = Pu emin.y = 12.89kN.m
10. Check Design Moment
(1) Calculate design moment
Mc.x = Mux = -116kN.m
Mc.y = Muy = 0.000kN.m
Mc = 116kN.m
11. Check Design Parameter
(1) Calculate rebar ratio
Ag = 90,000mm^2, Ast = 3,770mm^2
ρmin = 0.0100, ρmax = 0.0800, ρ = 0.0419
ρmin < ρ < ρmax -> O.K
(2) Calculate eccentricity
ex = Mc.y / Pu = 0.000mm
ey = Mc.x / Pu = 215mm
e = Mc / Pu = 215mm
Rotation angle of neutral axis = 0.000°
(3) Calculate concentric axial load capacity
P0 = 0.85f'c ( Ag - Ast ) + fy Ast = 3,635kN
[Link] = 0.80P0 = 2,908kN
Pt = fy Ast = -1,479kN
12. Check Moment Capacity
(1) Calculate capacity of compression stress block
β1 = 0.840
c = 163mm, a = β1 ㆍ c = 137mm
Acom = 41,145mm^2
ccx = 0.000mm, ccy = 81.42mm
Cc = 0.85 ㆍ f'c ㆍ Acom = 1,029kN
Mnx = Cc ㆍ ccx = 83.78kN.m
Mny = Cc ㆍ ccy = 0.000kN.m
(2) Calculate capacity of rebar
ds fs As Fs dy Mnx dx Mny
i εs
(mm) (MPa) (mm^2) (kN) (mm) (kN) (mm) (kN)
1 270 -0.001961 -392 314 -123 -120 14.79 -120 14.79
2 190 -0.000491 -98.26 314 -30.87 -40.00 1.235 -120 3.704
3 110 0.000979 196 314 61.49 40.00 2.460 -120 -7.379
4 30.00 0.002449 392 314 123 120 14.79 -120 -14.79
5 30.00 0.002449 392 314 123 120 14.79 -40.00 -4.929
6 30.00 0.002449 392 314 123 120 14.79 40.00 4.929
7 30.00 0.002449 392 314 123 120 14.79 120 14.79
8 110 0.000979 196 314 61.49 40.00 2.460 120 7.379
9 190 -0.000491 -98.26 314 -30.87 -40.00 1.235 120 -3.704
10 270 -0.001961 -392 314 -123 -120 14.79 120 -14.79
11 270 -0.001961 -392 314 -123 -120 14.79 40.00 -4.929
12 270 -0.001961 -392 314 -123 -120 14.79 -40.00 4.929
2018-08-14 2
[Link]
TEPO SOLE CO., LTD 020 22300188
MEMBER NAME : C01
∑Fs = 61.25kN
∑Mnx = 126kN.m
∑Mny = 0.000kN.m
(3) Calculate nominal capacity for neutral axis
Pb = Cc + Ps = 1,090kN
Mnx = [Link] + [Link] = 209kN.m
Mny = [Link] + [Link] = 0.000kN.m
Mn = Mnx 2 + Mny 2 = 209kN.m
(4) Calculate strength reduction factor
ε[Link] = 0.0020, ε[Link] = 0.0050
εt = 0.002365
ø = 0.680
(5) Calculate axial load and moment capacities
øPn = 651kN
øMnx = 142kN.m
øMny = 0.000kN.m
øMn = 142kN.m
Mux / øMnx = 0.814 < 1.000 -> O.K
Muy / øMny = 0.000 < 1.000 -> O.K
Pu / øPn = 0.825 < 1.000 -> O.K
Mc / øMn = 0.814 < 1.000 -> O.K
P (kN)
3750
θ=0.00˚
N.A=0.00˚
3225
2700
2175
1890
1650
1125 eb=163.26mm
(651,142)
600
(537,116)
0 75 M (kN.m)
-450
-975
-1500
0
100
125
150
175
200
225
250
25
50
75
13. Check Shear Capacity
(1) Calculate maximum space
ø = 0.750
Smax = min(16DMainBar , 48DStirrup , B, D) = 300mm
(2) Calculate shear strength (Direction X)
s = 0.00100mm < smax = 300mm -> O.K
øVc = ø0.17 f'c bw d = 56.02kN
Av fyt d
øVs = ø = 125kN
s
øVn = øVc + øVs = 181kN
Vu / øVn = 1.555 -> N.G
2018-08-14 3
