RV Series

Relief Valves
Catalog No. H-RV100
Jan. 2002

R V1 RV2
Series Low Pressure Relief Valve High Pressure Relief Valve Series
Cap

Cracking Pressure
Adjusting Nut

Label
Lack Wire Lack Wire
Hole Hole
Adjustable
Spring

Locking
Nut

Bonnet

Stem

Stem Seal

Seat Ring

Body

Technical Data
ƒƒ Cracking Pressure Range: 10~250 psig to atmosphere ƒƒ Cracking Pressure Range: 225~6000 psig to atmosphere
ƒƒ [Link] Pressure: 300 psig ƒƒ [Link] Pressure: 6000 psig
ƒƒ Operating Temperature Range: -10 °F ~ 400 °F (-23 °C ~ 204 °C) ƒƒ Operating Temperature Range: -10 °F ~ 400 °F (-23 °C ~ 204 °C)
ƒƒ Orifice Size : 4.8mm (0.19in) ƒƒ Orifice Size: 4.8mm (0.19in)
ƒƒ One Spring adjustable over entire cracking pressure range, ƒƒ Various Springs are available as below mentioned.
blue-color spring standard ƒƒ Cracking Pressure is not affected by the outlet pressure.
ƒƒ Cracking Pressure is not affected by the outlet pressure.

Features RV2 Series Spring and Cracking Pressure

ƒƒCompact body for installation in small space
Cracking Pressure
ƒƒCracking pressure adjustaple externally Spring
Designator psig bar kPa Color
ƒƒLock wire capability to maintain pressure relief setting
ƒƒ100% factory tested crack and reseal performance A 225 - 750 15.5 - 51.5 1550 - 5150 Yellow
B 750 - 1500 51.5 - 103 5150 - 10300 Purple
Materials of Construction C 1500 - 2250 103 - 155 10300 - 15500 Orange
ƒƒBody Material : Stainless Steel 316 (standard) D 2250 - 3000 155 - 206 15500 - 20600 Brown
ƒƒSeal : Viton (standard)
E 3000 - 4000 206 - 275 20600 - 27500 White
ƒƒSpring : SS631 (standard)
F 4000 - 5000 275 - 344 27500 - 34400 Red
ƒƒCap : Polypropylene (standard)
G 5000 - 6000 344 - 414 34400 - 41400 Green
Valve Operation and Adjusting Cracking CAUTION
pressure
RV Series Relief Valves are not "Safety Accessories" as
To increase the cracking pressure, turn the cracking pressure defined in the Pressure Equipment Directive 97/23/EC.
adjusting nut clockwise making the spring more compressed.

© 1998, 2000, 2002 HY-LOK CORPORATION All rights reserved

 Relief Valves RV Series

Table of Dimensions
Orifice End Connections Dimensions
Basic Part No.
Hole Inlet Outlet L1 L2 L3
H -4 T- 1/4" Hy-Lok 1/4" Hy-Lok
H -6M- 6mm Hy-Lok 6mm Hy-Lok 38.7 37.3 104.6
H -8M- 8mm Hy-Lok 8mm Hy-Lok
H -8 T- 1/2" Hy-Lok 1/2" Hy-Lok
46.7 114.0
RV1 H -12M- 12mm Hy-Lok 12mm Hy-Lok
or 4.8 46.7
RV2 MH -8N8T- 1/2" Male NPT 1/2" Hy-Lok
35.7 103.0
MH -8N12M- 1/2" Male NPT 12mm Hy-Lok
MF -4N- 1/4" Male NPT 1/4" Female NPT 30.0
32.2 99.5
MF -6N- 3/8" Male NPT 3/8" Female NPT 34.5
MF -8N- 1/2" Male NPT 1/2" Female NPT 38.0 35.7 103.0
All dimensions in millimeters.

Ordering Information

Series Designator Spring / Cracking

ƒƒ RV1 : Low Pressure Size Designator
Pressure Designator *
ƒƒ RV2 : High Pressure Inlet / Outlet ƒƒ A : 225 - 750 psig
End Connection Designator
ƒƒ B : 750 - 1500 psig Body Material Designator
ƒƒ H : Both End Hy-Lok Tube Fitting ƒƒ C : 1500 - 2250 psig ƒƒ S316 : 316 Stainless
ƒƒ MH : Male Pipe Thread & Hy-Lok Tube Fitting ƒƒ D : 2250 - 3000 psig Steel
ƒƒ MF : Male Pipe Thread & Female Pipe Thread ƒƒ E : 3000 - 4000 psig
ƒƒ F : 4000 - 5000 psig
ƒƒ G : 5000 - 6000 psig
ƒƒ NPT (ISO/BSP)
Thread (in.) 1/4 3/8 1/2
Designator 4N(R) 6N(R) 8N(R)

ƒƒ Tube
Fractional O.D.(in.) 1/4 3/8 1/2
Tube Designator 4T 6T 8T
Metric O.D.(mm) 6 8 12
Tube Designator 6M 8M 12M
SAFETY in VALVE SELECTION
Note * : No spring/cracking pressure designator is required for RV1 low
pressure series valves. Proper installation, materials compatibility, operation and
maintenance of these valves are the responsibility of the user.
The total system design must be taken into consideration to
ensure optimal performance and safety.

2 An der Autobahn 15 Tel.: +49 4207 6994 - 0 E-Mail: info@[Link]

D-28876 Oyten Fax: +49 4207 6994 - 40 Web: [Link]