TRAINING PLAN

Qualification Electrical Installation and Maintenance

Trainees’ Date
Training Mode of Facilities/Tools Assessment
Training Staff Venue and
Activity/Task Training and Equipment Method
Requirements Time

1. Prepare  Electrical Self-pace UKC Direct October

Electrical power and Builders Observation 1-4,
Power and hydraulic tools , Tablon, 2018
Hydraulic are identified Actual Cagayan Oral
Tools and selected in Demonstration de Oro Questioning 40 hrs
line with job Chariss  Portable
Joy C. Electric City
specification Demonstration
Lacaya Drill
 Tools are (Trainer)  Portable
inspected for Band Saw Oral
Self-pace
damage in line  Angle Questioning
with Actual Grinder
enterprise Demonstration Engr.  Heat Gun Demonstration
requirements Abraham  Jack
G. Hammer
 Damaged tools Telesforo  Hydraulic
are reported to Jr.- UKC Pipe Oral
supervisor and Builders Bender Questioning
repaired Self-pace
Training  PPE
according to Actual Supervisor Actual
manufacturer’s Demonstration Demonstration
specifications

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS Page |9
Training Plan Chariss Joy C. Lacaya Revision No.00
  Electrical  Oil
power and Self-pace  Solid Oral
hydraulic tools Lubricants Questioning
are lubricated  Rust
in line with Actual Remover Demonstration
enterprise Demonstration  Dry
requirements Lubricants
 Penetrating
Lubricants
 Synthetic
Oils
 Gasoline
 Diesoline
 Kerosene
 Thinner
 Auxiliary parts
of power Self-pace Oral
tools/hydraulic Questioning
tools are
inspected and Actual Demonstration
replaced Demonstration
according to
manufacturer’s
specifications

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 10
Training Plan Chariss Joy C. Lacaya Revision No.00
  Electrical
power and Self-pace Oral
hydraulic tools Questioning
are safely Actual
stored in line Demonstration Actual
with enterprise Demonstration
requirements
 Correct
drawings are Self-pace Oral
interpreted Questioning
2. Perform based on job
Roughing-In requirements Lacaya,
Activities for  Correct Chariss
Communicati quantities of  Rigid Steel
Self-pace Joy C. Oral
on and conduit and Conduits
(Trainer) Questioning
Distribution accessories are (RSC)
Systems determined as  Intermediat
per job e Metallic
requirements Conduit UKC October
(IMC) Builders 8-24,
Engr.  Electrical 2018
, Tablon,
Abraham Metallic Cagayan
G. Tubing 90 hrs
de Oro
Telesforo (EMT) City
Jr.- UKC  Entrance
Builders cap
Training  Hacknut
Supervisor and
bushing
 Metal strap

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 11
Training Plan Chariss Joy C. Lacaya Revision No.00
  Tools and  Spirit level
equipment are Self-pace  Hack saw Oral
selected as per  Pipe cutter Questioning
job  Plumb bob
requirements  Pipe reamer
 Pipe
threaded
 Pipe bender
 Bolt cutter

 Conduit is
assembled Self-pace Actual
ensuring that Demonstration
fittings are fully
inserted and Actual
tightened as Demonstration
per job
requirements
 Conduit is bent
with bends not Self-pace Actual
exceeding 90° Demonstration
as per job
requirements Actual
Demonstration
 Conduit
couplings and Self-pace Actual
elbows are Demonstration
installed as per Actual
job Demonstration
requirements
Date Developed: Document No. ONSTS-EIM-01
Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 12
Training Plan Chariss Joy C. Lacaya Revision No.00
  Conduit is Self-pace
threaded in line Actual Actual
with job Demonstration Demonstration
requirements
 Safety
procedures are Self-pace Actual
followed in line Demonstration
with standard Actual
operating Demonstration
procedures
(SOPs)
 Correct
drawings are Self-pace Oral
interpreted to
determine job Questioning
requirements
 Correct
quantities of Self-pace Oral
materials are
selected as per Questioning
job
requirements
 Tools and  Screwdriver
equipment are Self-pace s Oral
selected as per  Pliers Questioning
job  Hickey
requirements Actual  L-Square
Demonstration  Bench Vise Actual
 Metric Rule Demonstration
 Electric
Date Developed: Document No. ONSTS-EIM-01
Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 13
Training Plan Chariss Joy C. Lacaya Revision No.00
 Drill
 Spirit level
 Hack saw
 Pipe cutter
 Plumb bob
 Pipe reamer
 Pipe
threaded
 Pipe bender
 PPE
 Testing
Measureme
nts
 Bolt cutter
 Wire ways and Self-pace Oral
cable trays are Questioning
Actual
installed as per Demonstration Actual
job Demonstration
requirements
 Safety Self-pace Oral
procedures are Actual Questioning
followed in line Demonstration Actual
with SOPs Demonstration
 Correct
drawings are Self-pace Oral
interpreted to
determine job Questioning
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 14
Training Plan Chariss Joy C. Lacaya Revision No.00
  Correct
quantities of Self-pace Oral
materials are
selected as per Questioning
job
requirements
 Tools and Self-pace  Screwdriver Oral
equipment are s Questioning
Actual
selected as per Demonstration  Pliers Actual
job  Hickey Demonstration
requirements  L-Square
 Bench Vise
 Metric Rule
 Electric
Drill
 Spirit level
 Hack saw
 Pipe cutter
 Plumb bob
 Pipe reamer
 Pipe
threaded
 Pipe bender
 PPE
 Testing
Measureme
nts
 Bolt cutter

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 15
Training Plan Chariss Joy C. Lacaya Revision No.00
  Telephone
terminal Self-pace Actual
cabinet is
installed as per Actual Demonstration
job Demonstration
requirements
 Telephone
main Self-pace Actual
distribution is
installed as per Actual Demonstration
job Demonstration
requirements
 Safety
procedures are Self-pace Actual
followed in line
with SOPs Actual Demonstration
Demonstration
 Correct
drawings are Self-pace Oral
interpreted
based on job Questioning
requirements
 Correct
quantities of Self-pace Oral
materials are Questioning
selected as per
job
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 16
Training Plan Chariss Joy C. Lacaya Revision No.00
  Tools and  Screwdriver
equipment are Self-pace s Oral
selected as per  Pliers
job  Hickey Questioning
requirements Actual  L-Square
Demonstration  Bench Vise
Actual
 Metric Rule Demonstration
 Electric
Drill
 Spirit level
 Hack saw
 Pipe cutter
 Plumb bob
 Pipe reamer
 Pipe
threaded
 Pipe bender
 PPE
 Testing
Measureme
nts
 Bolt cutter
 Cable bridge is Self-pace Oral
installed as per Questioning
job Actual Actual
requirements Demonstration Demonstration

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 17
Training Plan Chariss Joy C. Lacaya Revision No.00
  Safety Self-pace
procedures are Actual
followed in line Actual Demonstration
with SOPs Demonstration
 Final checks
are made to Self-pace Direct
ensure that Observation
work conforms
with Actual
instructions Demonstration
and job
requirements
 Supervisor is Direct
notified upon Self-pace Observation
completion of
work
 Tools,  Screwdriver
equipment and Self-pace s Direct
any surplus  Pliers Observation
resources and  Hickey
materials are, Actual  L-Square
where Demonstration  Bench Vise Actual
appropriate,  Metric Rule Demonstration
cleaned,  Electric
checked and Drill
returned to  Spirit level
storage in  Hack saw
accordance
 Pipe cutter
with
 Plumb bob
established
procedures  Pipe reamer
Date Developed: Document No. ONSTS-EIM-01
Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 18
Training Plan Chariss Joy C. Lacaya Revision No.00
  Pipe
threaded
 Pipe bender
 PPE
 Testing
Measureme
nts
 Bolt cutter
 Work area is Direct
cleaned up and Observation
Actual
made safe Demonstration Actual
according to Demonstration
OHSA
regulations
 Drawings are
3. Install read and Self-pace Lacaya, Oral
Wiring interpreted to Chariss Questioning
Devices for determine job Joy C.
Floor and requirements (Trainer)
Ground Fault  Correct type  Pliers
Current and quantity of Engr.  Screwdriver
Self-pace Abraham Oral
Interrupting wiring devices s
G. Questioning
Outlets and other  Electric October
Telesforo UKC
materials are Actual Drill 29-31,
Jr.- UKC Builders
identified in Demonstration  Testing Actual 2018
Builders , Tablon,
line with job Measureme Cagayan Demonstration
requirements Training 30 hrs
nts de oro
Supervisor
 Metric Rule City

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 19
Training Plan Chariss Joy C. Lacaya Revision No.00
  Tools and Self-pace  Hickey/Ben Oral
equipment are ch Questioning
selected in line Vise/Heat Actual
with job Actual Gun Demonstration
requirements Demonstration  Wrenches
 Wire
splicers
 Knives
 Correct PPE Actual  Safety Direct
are identified Demonstration Clothes Observation
and selected in  Gloves Actual
line with safety  Googgles Demonstration
requirements
 Safety Direct
procedures are Observation
Actual
followed based Demonstration Actual
on safety Demonstration
regulations
 Correct Direct
procedures for Observation
Actual
installation of Demonstration Actual
wiring devices Demonstration
are performed
in line with job
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 20
Training Plan Chariss Joy C. Lacaya Revision No.00
  Schedule of
work is Self-pace Oral
followed based Questioning
on agreed time,
quality
standard and
minimum
wastage
 Further
instructions Self-pace Oral
are sought if Questioning
unplanned
events or
conditions
occur
 On-going
checking of Self-pace Oral
quality of work Questioning
are done in
accordance Actual
with Demonstration
instructions
and
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 21
Training Plan Chariss Joy C. Lacaya Revision No.00
  Final checks
are made to Self-pace Direct
ensure that Observation
work conforms
with Actual
instructions Demonstration
and to
requirements
 Supervisor is Direct
notified upon Observation
Self-pace
completion of
work
 Tools,  Pliers
equipment and  Screwdriver Direct
any surplus s Observation
resources and Self-pace  Electric
materials are, Drill
where  Testing Actual
appropriate, Actual
Measureme Demonstration
cleaned, Demonstration
nts
checked and  Metric Rule
returned to  Hickey/Ben
storage in ch
accordance Vise/Heat
with Gun
established  Wrenches
procedures  Wire
splicers
 Knives
 PPE
Date Developed: Document No. ONSTS-EIM-01
Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 22
Training Plan Chariss Joy C. Lacaya Revision No.00
  Work area is Actual Direct
cleaned and Demonstration Observation
made safe Actual
Demonstration
4. Install  Instructions for Novemb
Electrical the preparation er 5-8,
Self-pace Lacaya, Direct
Protection of the work 2018
Chariss Observation
System for activity are Joy C.
Lighting and communicated 30 hrs
(Trainer)
Grounding and confirmed
to ensure clear UKC
understanding Builders
, Tablon,
 Tools,  Screwdriver
Cagayan
equipment and Self-pace s Oral
de Oro
PPE needed to Engr.  Pliers Questioning
City
install Abraham  Electric
electrical wiring Actual G. Drill
are identified, Demonstration Telesforo  Testing Actual
checked to Jr.- UKC Measureme Demonstration
ensure they Builders nt
work correctly Training  Metric Rule
as intended Supervisor  Wire
and are safe to Splicers
use in  Knives
accordance  Hickey/Ben
with ch
established Vise/Heat
procedures Gun
 PPE

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 23
Training Plan Chariss Joy C. Lacaya Revision No.00
  Materials
needed for Self-pace Direct
work are Observation
obtained in
accordance
with
established
procedures
 Safety Actual Actual
procedures are Demonstration Demonstration
followed
 Correct
procedures for Self-pace Oral
installation of Questioning
electrical
protection Actual
system are Demonstration Actual
performed in Demonstration
line with job
requirements
and PEC

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 24
Training Plan Chariss Joy C. Lacaya Revision No.00
  Schedule of
work is Self-pace Oral
followed to Questioning
ensure work is
completed in
an agreed time,
to a quality
standard and
with a
minimum
waste
 Further
instructions Self-pace Oral
are sought Questioning
from a
supervisor if
unplanned
events or
conditions
occur
 On-going
checks of Self-pace Direct
quality of work Observation
are done in
accordance
with Actual
instructions Demonstration
and
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 25
Training Plan Chariss Joy C. Lacaya Revision No.00
  Final checks
are made to Self-pace Oral
ensure the Questioning
work conforms
with
instructions
and
requirements
 Supervisor is
notified upon Self-pace Oral
completion of Questioning
work
 Tools,  Screwdriver
equipment and Self-pace s Direct
any surplus  Pliers Observation
resources and  Electric
materials are, Actual Drill
where Demonstration  Testing Actual
appropriate, Measureme Demonstration
cleaned, nt
checked and  Metric Rule
returned to  Wire
storage in Splicers
accordance  Knives
with  Hickey/Ben
established ch
procedures Vise/Heat
Gun

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 26
Training Plan Chariss Joy C. Lacaya Revision No.00
  Work area is Actual Actual
cleaned and Demonstration Demonstration
made safe
5. Install  Instructions for UKC
Electrical the preparation Builders
Self-pace Direct
Lighting of the work , Tablon, Observation
System On activity are Cagayan
Auxiliary communicated de oro Novemb
Outlets and and confirmed City er 12-
Lighting to ensure clear Lacaya, 23,
Fixtures understanding Chariss 2018
Joy C.
 Tools,
(Trainer) 60 hrs
equipment and Self-pace Oral
personnel Questioning
protective  Pliers
equipment Actual  Screwdriver
(PPE) needed to Demonstration s Actual
install  Wrenches Demonstration
electrical wiring  Wire
are identified, Engr.
 Splicers
checked to Abraham
 Knives
ensure the G.
Telesforo  PPE
work is done as
intended and Jr.- UKC
are safe to use Builders
in accordance Training
with Supervisor
established
procedures

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 27
Training Plan Chariss Joy C. Lacaya Revision No.00
  Materials
needed for Self-pace Oral
work are Questioning
obtained in
accordance Actual
with Demonstration Actual
established Demonstration
procedures
 Materials
needed to do Self-pace Oral
the work are Questioning
estimated
according to Actual
job Demonstration Actual
requirements Demonstration
 Safety Self-pace Direct
procedures are Observation
Actual
followed Demonstration Actual
Demonstration
 Correct
procedures for Actual Direct
installation of Demonstration Observation
lighting fixtures
are performed
in line with job Actual
requirements Demonstration

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 28
Training Plan Chariss Joy C. Lacaya Revision No.00
  Schedule of
work is Self-pace Direct
followed to Observation
ensure work is
completed in
an agreed time,
to a quality
standard and
with a
minimum
waste
 Further
instructions Self-pace Direct
are sought Observation
from a
supervisor if
unplanned
events or
conditions
occur
 On-going
checks of Self-pace Direct
quality of work Observation
are undertaken
in accordance
with
instructions
and
requirements

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 29
Training Plan Chariss Joy C. Lacaya Revision No.00
  Final checks
are made to Self-pace Direct
ensure that Observation
work conforms
with
instructions
and
requirements
 Supervisor is
notified upon Self-pace
completion of
work
 Tools,
equipment and Self-pace Direct
any surplus Observation
resources and
materials are, Actual
where Demonstration Actual
appropriate, Demonstration
cleaned,
checked and
returned to
storage in
accordance
with
established
procedures
 Work area is Actual Actual
cleaned and Demonstration Demonstration
made safe

Date Developed: Document No. ONSTS-EIM-01

Supervise Work Based Learning September 26, 2018 Issued by:
Developed by: ONSTS P a g e | 30
Training Plan Chariss Joy C. Lacaya Revision No.00