Scribd
Upload
182 views5 pages

Configure VLAN and TFTP on Cisco Switch

The document discusses configuration and troubleshooting of a network device. It logs into the device, checks interface and IP configurations, pings an IP to check connectivity, copies a new software image to flash, and verifies the boot configuration.

Uploaded by

Juan Cordoba
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
182 views5 pages

Configure VLAN and TFTP on Cisco Switch

The document discusses configuration and troubleshooting of a network device. It logs into the device, checks interface and IP configurations, pings an IP to check connectivity, copies a new software image to flash, and verifies the boot configuration.

Uploaded by

Juan Cordoba
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd

Format FAT32

allocation unit size 2048 or 4096

login as: Jef3.S1stemas


Using keyboard-interactive authentication.
Password:

CFBE31>enable
Password:
CFBE31#sh file sys
File Systems:

Size(b) Free(b) Type Flags Prefixes


- - opaque ro bs:
* 57931776 42637312 flash rw flash:
- - opaque rw system:
- - opaque rw tmpsys:
524288 512797 nvram rw nvram:
- - opaque rw null:
- - opaque ro tar:
- - network rw tftp:
- - opaque ro xmodem:
- - opaque ro ymodem:
- - network rw rcp:
- - network rw http:
- - network rw ftp:
- - network rw scp:
- - network rw https:
- - opaque ro cns:
- - usbflash rw usbflash0:

CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#sh run int vlan 10
Building configuration...

Current configuration : 62 bytes


!
interface Vlan10
ip address [Link] [Link]
end

CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#sh run int vlan 10
Building configuration...

Current configuration : 62 bytes


!
interface Vlan10
ip address [Link] [Link]
end

CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
CFBE31#sh ip int br
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned YES NVRAM administratively down down
Vlan10 [Link] YES manual up up
Vlan50 [Link] YES NVRAM up up
FastEthernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 unassigned YES unset up up
GigabitEthernet0/2 unassigned YES unset down down
GigabitEthernet0/3 unassigned YES unset up up
GigabitEthernet0/4 unassigned YES unset down down
GigabitEthernet0/5 unassigned YES unset down down
GigabitEthernet0/6 unassigned YES unset up up
GigabitEthernet0/7 unassigned YES unset down down
GigabitEthernet0/8 unassigned YES unset up up
GigabitEthernet0/9 unassigned YES unset down down
GigabitEthernet0/10 unassigned YES unset up up
GigabitEthernet0/11 unassigned YES unset up up
GigabitEthernet0/12 unassigned YES unset down down
GigabitEthernet0/13 unassigned YES unset down down
GigabitEthernet0/14 unassigned YES unset up up
GigabitEthernet0/15 unassigned YES unset up up
GigabitEthernet0/16 unassigned YES unset up up
GigabitEthernet0/17 unassigned YES unset down down
GigabitEthernet0/18 unassigned YES unset down down

CFBE31#sho ip arp | i [Link]


CFBE31#sho ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet [Link] 119 0081.c408.ef42 ARPA Vlan50
Internet [Link] - d0c7.89fc.63c1 ARPA Vlan50
Internet [Link] - d0c7.89fc.63c2 ARPA Vlan10
CFBE31#sh run int gig1/0/1
^
% Invalid input detected at '^' marker.

CFBE31#sh run int gi1/0/1


^
% Invalid input detected at '^' marker.

CFBE31#sh ip int br
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned YES NVRAM administratively down down
Vlan10 [Link] YES manual up up
Vlan50 [Link] YES NVRAM up up
FastEthernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 unassigned YES unset up up
GigabitEthernet0/2 unassigned YES unset down down
GigabitEthernet0/3 unassigned YES unset up up
GigabitEthernet0/4 unassigned YES unset down down
GigabitEthernet0/5 unassigned YES unset down down
GigabitEthernet0/6 unassigned YES unset up up
GigabitEthernet0/7 unassigned YES unset down down
GigabitEthernet0/8 unassigned YES unset up up
GigabitEthernet0/9 unassigned YES unset down down
GigabitEthernet0/10 unassigned YES unset up up
GigabitEthernet0/11 unassigned YES unset up up
GigabitEthernet0/12 unassigned YES unset down down
GigabitEthernet0/13 unassigned YES unset down down
GigabitEthernet0/14 unassigned YES unset up up
GigabitEthernet0/15 unassigned YES unset up up
GigabitEthernet0/16 unassigned YES unset up up
GigabitEthernet0/17 unassigned YES unset down down
GigabitEthernet0/18 unassigned YES unset down down

CFBE31#sh run int gi0/1


Building configuration...

Current configuration : 88 bytes


!
interface GigabitEthernet0/1
switchport access vlan 998
switchport mode access
end

CFBE31#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CFBE31(config)#int vlan 998
CFBE31(config-if)#exit
CFBE31(config)#no int vlan 10
CFBE31(config)#int vlan 998
CFBE31(config-if)#ip add
CFBE31(config-if)#ip address [Link] [Link]
CFBE31(config-if)#exit
CFBE31(config)#exit
CFBE31#ping [Link]

Type escape sequence to abort.


Sending 5, 100-byte ICMP Echos to [Link], timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/203/1007 ms
CFBE31#copy tftp: flash:
Address or name of remote host []? [Link]
Translating "[Link]"

?Invalid host address or name


%Error parsing filename (Invalid IP address or hostname)
CFBE31#copy tftp: flash:
Address or name of remote host []? [Link]
Source filename []? [Link]
Destination filename [[Link]]?
Accessing t[Link]
Loading [Link] from [Link] (via Vlan998): !!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 16800768 bytes]

16800768 bytes copied in 218.518 secs (76885 bytes/sec)


CFBE31#sh flash:
4194288K bytes of USB Flash usbflash0 (Read/Write)

Directory of flash:/

2 -rwx 3518 Feb 28 1993 [Link] -05:00 [Link]


3 -rwx 2116 Mar 1 1993 [Link] -05:00 [Link]
4 -rwx 4120 Feb 28 1993 [Link] -05:00 multiple-fs
5 -rwx 3825 Feb 28 1993 [Link] -05:00 [Link]
586 -rwx 16800768 Mar 1 1993 [Link] -05:00 c2960s-universalk9-mz.152-
[Link]
6 drwx 512 Feb 28 1993 [Link] -05:00 c2960s-universalk9-mz.122-
55.SE7

57931776 bytes total (25700864 bytes free)


CFBE31#sh flash:
4194288K bytes of USB Flash usbflash0 (Read/Write)

Directory of flash:/

2 -rwx 3518 Feb 28 1993 [Link] -05:00 [Link]


3 -rwx 2116 Mar 1 1993 [Link] -05:00 [Link]
4 -rwx 4120 Feb 28 1993 [Link] -05:00 multiple-fs
5 -rwx 3825 Feb 28 1993 [Link] -05:00 [Link]
586 -rwx 16800768 Mar 1 1993 [Link] -05:00 c2960s-universalk9-mz.152-
[Link]
6 drwx 512 Feb 28 1993 [Link] -05:00 c2960s-universalk9-mz.122-
55.SE7

57931776 bytes total (25700864 bytes free)


CFBE31#sh run | i boot
boot-start-marker
boot-end-marker
CFBE31#sho boot
BOOT path-list : flash:/c2960s-universalk9-mz.122-55.SE7/c2960s-universalk9-
[Link]
Config file : flash:/[Link]
Private Config file : flash:/[Link]
Enable Break : no
Manual Boot : no
HELPER path-list :
Auto upgrade : yes
Auto upgrade path :
NVRAM/Config file
buffer size: 524288
Timeout for Config
Download: 0 seconds
Config Download
via DHCP: disabled (next boot: disabled)
CFBE31#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CFBE31(config)#boot system flash:[Link]
CFBE31(config)#do wr mem
Building configuration...
[OK]
CFBE31(config)#exit
CFBE31#sh boot
BOOT path-list : flash:[Link]
Config file : flash:/[Link]
Private Config file : flash:/[Link]
Enable Break : no
Manual Boot : no
HELPER path-list :
Auto upgrade : yes
Auto upgrade path :
NVRAM/Config file
buffer size: 524288
Timeout for Config
Download: 0 seconds
Config Download
via DHCP: disabled (next boot: disabled)
CFBE31#reload
Proceed with reload? [confirm]

You might also like