GTO Series

1201.1
1201.1II
1 CHANNEL POWER AMPLIFIER

SERVICE MANUAL

JBL Consumer Products

250 Crossways Park Dr.
Woodbury, New York 11797 Rev2aa10/2005

Downloaded from www.Manualslib.com manuals search engine

 Power Amplifier GTO 1201.1/1201.1II
- CONTENTS -

SPECIFICATIONS ………………………………….……..1
FEATURES/TEST CONDITIONS……..…………………2
INSTALLATION………………….……...……..…...…...…3
CONNECTIONS………………….……...……..…...…..…4
SET-UP/CONTROLS ……..………………..…….….…...5
INSTALLING NEON TUBES..…….…….………………..5
BASIC TROUBLESHOOTING..…….…….………………6
TYPICAL SYSTEM WIRING..…….…….……………..…7
EXPLODED VIEW/PARTS LIST…….….….…………....8
MECHANICAL PARTS LIST..…….…….……………......9
AMPLIFIER BLOCK DIAGRAM…………………….……10
P.C.B. DRAWINGS….……………………………….…….11
ELECTRICAL PARTS LIST ..……….……….…….….…14
VERSION II ELECTRICAL PARTS LIST ADDENDUM….……….18
IC/TRANSISTOR PINOUTS..……..….…….….….….…..19
GTO 1201.1 SCHEMATICS………..……………..……...25
GTO 1201.1II SCHEMATICS………..…………………...28
PACKING……..…………………………………………....31

GTO 1201.1/ GTO 1201.1II Specifications

Output Power: 787W RMS x 1 channels @ 4 ohms; ≤1% THD + N

(14.4V supply) 1114W RMS x 1 channels @ 2 ohms; ≤1% THD + N
Signal-to-noise ratio: 70dBA (reference 1W into 4 ohms)
Dynamic power: 1339W @ 2 ohms
Effective damping factor: 6.34 @ 4 ohms
Frequency response: 10Hz – 302Hz (–3dB)
Maximum input signal: 6.1V
Maximum sensitivity: GTO 1201.1 - 140mV
GTO 1201.1II - 75mV
DC Offset <50mV (-50%)
Output regulation: .14dB @ 4 ohms
Idle Current 2.3A
Input Impedance 22kΩ
Max Current Draw 73A @ 4 ohms
125A @ 2 ohms
Dimensions: 18 11/16 x 12 5/16 x 2 3/8” (L x W x D)
(474mm x 313mm x 60mm)
Fuses: 40A x 3

JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in
this and related JBL publications are therefore subject to change without notice.

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

2
Downloaded from www.Manualslib.com manuals search engine
54 PM Page 2

GTO1201.1/1201.1II
INSTALLATION

WARNING: Playing loud music in an • Before drilling or cutting holes, use a POWER CONNECTIONS Speaker Connections
automobile can hinder your ability to hear utility knife to remove unwanted fabric The GTO amplifiers are capable of Refer to the application guides on the
traffic and permanently damage your or vinyl to keep material from snagging delivering extremely high power levels, pages that follow. Speaker connections
hearing. We recommend listening at low or in a drill bit. and require a heavy-duty and reliable should be made using a minimum of
moderate levels while driving your car. JBL • When routing cables, keep input-signal connection to the vehicle’s electrical system 16-gauge wire.
accepts no liability for hearing loss, bodily cables away from power cables and in order to perform optimally. See Figure 1
injury or property damage resulting from speaker wires. for connection location. Please adhere to
the use or misuse of this product. • When making connections, make the following instructions carefully:
certain they are secure and properly
IMPORTANT: To get the best insulated. Ground Connection
performance from your JBL Grand Touring® Connect the amplifier’s Ground (GND)
• If the amplifier’s fuse must be replaced,
Series amplifiers, we strongly recommend terminal to a solid point on the vehicle’s
use only the same type and rating as
that installation be entrusted to a qualified metal chassis, as close to the amplifier
that of the original. Do not substitute
professional. Although these instructions as possible. Refer to the chart below to
another kind.
explain how to install GTO amplifiers in a determine minimum wire-gauge size. Scrape
general sense, they do not show specific away any paint from this location; use a star-
installation methods that may be required CHOOSING A LOCATION type lock washer to secure the connection.
for your particular vehicle. If you do not AND MOUNTING THE
have the necessary tools or experience, AMPLIFIER Power Connection
do not attempt the installation yourself. Choose a mounting location in the trunk Connect a wire (see chart at right for NOTE: When using the high-level inputs,
Instead, please ask your authorized JBL or cargo area where the amplifier will not appropriate gauge) directly to the vehicle’s the AUX outputs can be used to pass a
car audio dealer about professional be damaged by shifting cargo. Amplifier positive battery terminal, and install an line-level signal to another amplifier.
installation. cooling is essential for proper amplifier appropriate fuse holder within 18" of the
operation. If the amplifier is to be installed battery terminal. Do not install the fuse at Wire Gauge Chart
INSTALLATION in an enclosed space, make sure there is this time. Route the wire to the amplifier’s Amplifier Maximum Minimum
WARNINGS AND TIPS sufficient air circulation for the amplifier location, and connect it to the amplifier’s Model Current Draw Wire Gauge
• Always wear protective eyewear when to cool itself. Positive (+12V) terminal. Be sure to use AWG
using tools. appropriate grommets whenever routing AWG
• Turn off the audio system and other When mounting the amplifier under a wires through the firewall or other sheet GTO1201.1 115A #4 AWG
electrical devices before you start. seat, ensure that it is clear of all moving metal. Failure to adequately protect the AWG
Disconnect the (–) negative lead from seat parts and does not affect the seat positive wire from potential damage may These recommendations assume 7' – 10'
your vehicle’s battery. adjustments. Mount the amplifier so it result in a vehicle fire. When you are done wire runs. If your installation differs mark-
is not damaged by the feet of backseat routing and connecting this wire, you may edly, you will need to adjust the wire
• Check clearances on both sides of
passengers. Make sure that the amplifier install the fuse at the battery. gauge accordingly.
a planned mounting surface before
is mounted securely using nuts and bolts
drilling any holes or installing any
or the supplied mounting screws. Remote Connection
screws. Remember that the screws
can extend behind the surface. Connect the amplifier’s Remote (REM)
Mount the amplifier so that it remains terminal to the source unit’s Remote Turn- IMPORTANT NOTE: If you are planning
• At the installation sites, locate and dry – never mount an amplifier outside On lead using a minimum of 18-gauge wire. to use optional neon tubes, install them
make a note of all fuel lines, hydraulic the vehicle or in the engine compartment. before making any electrical connections
brake lines, vacuum lines and electrical
NOTE: When using the speaker level to the amplifier (refer to“Installing Neon
wiring. Use extreme caution when cut-
inputs, connect the remote (REM) terminal Tubes” on page 5).
ting or drilling in and around these areas.
to the source unit. If your source unit does
not have a remote turn-on connection,
connect the amplifier’s (REM) terminal to
Figure 1. Terminal connection end plate. the vehicle’s accessory circuit.

Downloaded from www.Manualslib.com manuals search engine

TO Amp OM 2/3/04 3:54 PM Page 3

GTO 1201.1/1201.1II

CONNECTIONS – GTO1201.1/GTO1201.1II
The GTO subwoofer amplifiers are
single-channel amplifiers. There are
two sets of terminals to make it easy
to connect multiple woofers. Either
set of (+/–) terminals may be used
when connecting woofers.
To the right are two application
diagrams to help plan your subwoofer GTO Amplifier GTO Amplifier
(partial end panel) (partial end panel)
system installation. Figures 2 and 3
show how to configure the GTO
+ – +
subwoofer amplifiers – + –

Subwoofer Subwoofer Subwoofer

NOTE: For simplicity, Figures 2 and 3 Figure 2. GTO subwoofer amplifier with two woofer connections. Figure 3. GTO subwoofer amplifier with one woofer connection.
do not show power, remote and input
connections.

NOTE: Minimum speaker load is

2 ohms.

Downloaded from www.Manualslib.com manuals search engine

:54 PM Page 6

GTO1201.1/1201.1II

INSTALLATION AND SETUP

SETTING THE SETTING INPUT REMOTE LEVEL CONTROL INSTALLING NEON TUBES
CROSSOVER(S) SENSITIVITY All three GTO subwoofer (OPTIONAL)
Determine your system plans and set the 1. Initially turn the INPUT LEVEL control(s) amplifiers have inputs for an optional 1. Using a Phillips screwdriver, remove all
crossover mode switch accordingly. to minimum (counter clockwise). remote level control (RLC). This will allow screws on the amplifier’s output/power
2. Reconnect the (–) negative lead to the the amplifier’s input level to be adjusted end panel and set them aside.
Initially set the crossover frequency vehicle’s battery. Apply power to the from the listening position. Connect the 2. Using a 3 ⁄32-inch Allen wrench, remove
control midway. While listening to music, audio system and play a dynamic music optional remote level control using the only the screws on the amplifier’s (top)
adjust the crossover for the least track. RJ-11 jack on the side of the amplifier. clear cover and set them aside.
perceived distortion from the speakers, 3. On the source unit, increase the volume Install the control module in the front of 3. Remove the end panel and slide the
allowing them to reproduce as much control to 3/4 volume. Slowly increase the vehicle within easy reach of the driver. cover off. Set both parts aside.
bass as possible. the INPUT LEVEL control(s) toward three Under the dash or in the center console 4. Locate the enclosed hardware bag and
o’clock until you hear slight distortion are both suitable locations. remove the four clips. Each clip has a
Systems using a separate subwoofer set in the music. Then reduce the INPUT square end and a larger round end.
the crossover mode to HP (high pass) for LEVEL slightly until distortion is no SETTING THE BASS BOOST Using a round end, press two clips onto
your full-range speakers. Adjust the longer heard. All three GTO subwoofer amplifiers each neon tube (e.g., Street Glow AN9
crossover frequency to limit bass and are all equipped with a bass- or equivalent), as shown in Figure 13.
provide increased system volume with NOTE: After the source unit is on, red LEDs boost control. This allows you to adjust the 5. For each tube, align both clips so the
less distortion. (on the top panel) will light, indicating the bass output of your system at 50Hz up to square ends slide onto an exposed
amplifier is on. If not, check the wiring, 12dB and enhance low frequency. extrusion edge, as shown in Figure 9.
For subwoofers, choose the highest especially the remote connection from the Do not cover any screw holes. When
frequency that removes vocal information source unit. Also refer to “Troubleshooting” AUX OUTPUT installed correctly, each neon tube will
from the sound of the subwoofer. on the next page. All three GTO subwoofer amplifiers are sit under an extrusion and not be visible
equipped with full-range outputs that can when viewed from directly above.
be used to connect additional amplifiers. 6. Route each neon tube’s power cable
through its respective NEON hole on the
NOTE: When using the high-level inputs, end panel (see Figure 13).
the AUX outputs can be used to pass a 7. Slide the cover back into place and re-
line-level signal to another amplifier. install its screws. Then, replace the end
panel and reinstall its screws.
8. Finish the installation of the neon tubes
as instructed in their owner’s manual.
Figure 12.

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II
INSTALLATION AND SETUP

To Neon
Power
Supply

To Neon
Power
Supply

Figure 13. Installing neon tubes in a JBL GTO amplifier.

TROUBLESHOOTING

SYMPTOM LIKELY CAUSE SOLUTION SYMPTOM LIKELY CAUSE SOLUTION

No audio No voltage at BATT+ Check voltages at No audio Voltage more than 16V Check vehicle
(POWER LED or REM terminals, amplifier terminals (PROTECT or less than 8.5V on charging system for
is off) or bad or no ground with VOM LED is on) BATT+ connection defective voltage
connection regulator
No audio DC voltage on Amplifier may need Distorted audio Input sensitivity is Check INPUT
(PROTECT LED amplifier output service; see enclosed not set properly, or LEVEL setting; or
flashes every warranty card for amplifier or source check speaker wires
4 seconds) service information unit is defective for shorts or grounds
No audio Amplifier is Make sure amplifier Distorted audio Short circuit in Remove speaker leads
(PROTECT overheated cooling is not blocked and PROTECT speaker or wire one at a time to locate
LED is on) at mounting location; LED flashes shorted speaker or
verify speaker system wire, then repair
impedance is within Music lacks Speakers are not Check speaker
specified limits (see “punch” connected properly connections for
“Specifications” on proper polarity
the next page)
No audio Voltage less than 9V on Check vehicle
(PROTECT BATT+ connection charging system for
and POWER defective voltage
LEDs flash) regulator

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

Grand Touring

7
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

GTO 1201.1/1201.1II Mechanical Parts List

9
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

GTO 1201.1/1201.1II BLOCK DIAGRAM

10

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

11
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

12
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

13
Downloaded from www.Manualslib.com manuals search engine
 14
Downloaded from www.Manualslib.com manuals search engine
 15
Downloaded from www.Manualslib.com manuals search engine
 16
Downloaded from www.Manualslib.com manuals search engine
 17
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1 Version II Electrical Parts List Addendum

The following chart below represents the only electrical parts

differences in Version I and II models:

MODEL PART NAME PART NO SPEC DESIGNATOR

GTO 1201.1 RESISTOR RES-00-00756 1/5WJ 820 OHM R116
1
GTO 1201.1II RESISTOR RES-00-00474 1/5WF 240 OHM R116
GTO 1201.1 RESISTOR RES-00-00482 1/5WF 2K OHM R117
2
GTO 1201.1II RESISTOR RES-00-00577 1/5WF 750 OHM R117
GTO 1201.1 RESISTOR RES-00-00575 1/5WF 7.5K OHM R118
3
GTO 1201.1II RESISTOR RES-00-00402 1/5WF 10K OHM R118

GTO 1201.1 POWER TERMINAL TER-00-00238 (3P) WT-9842 TER1

4
GTO 1201.1II POWER TERMINAL TER-00-00277 (3P) DK-03B03-AG-1-DN TER1
GTO 1201.1 SPEAKER TERMINAL TER-00-00239 (4P) WT-9321 TER2
5
GTO 1201.1II SPEAKER TERMINAL TER-00-00275 (4P) DK-04A03-AG-1-DN TER2

18
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

19
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

20
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

21

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

22
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

23
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1/1201.1II

24
Downloaded from www.Manualslib.com manuals search engine
 GTO 1201.1 Page1 Schematic

25

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1 Page2 Schematic

26

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1 Page3 Schematic

27

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1II Page1 Schematic GTO 1201.1II

28

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1II Page2 Schematic GTO 1201.1II

29

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1II Page3 Schematic
GTO 1201.1II

30

Downloaded from www.Manualslib.com manuals search engine

 GTO 1201.1/1201.1II

Item Part Number Description Qty

BOX-36-147AB GTO 1201.1 Gift box carton 1

1
BOX-36-147AD GTO 1201.1II Gift box carton 1
2 INN-42-004A0 End Pads 2
GTO 1201.1 Owner’s manual 1
MAN-00-0195A
(USA)
GTO 1201.1II Owner’s manual 1
3 MAN-01-0195Z
(USA)
GTO 1201.1 Owner’s manual 1
MAN-00-0196A
(Europe)
CAR-WA-004A Warranty Card 1
4 FUS-AT-00008 Fuse 40A 3
SC4-NP-40250 Mounting screw STT1 PH 4X25 NI 6
BKT-14-523A0 Bracket lamp SK-5/BK 4
5 BOX-39-158AB Pair Pack carton 1

31
Downloaded from www.Manualslib.com manuals search engine