Code No: 133BJ R16
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
B.Tech II Year I Semester Examinations, November/December - 2017
NETWORK ANALYSIS
(Electronics and Communication Engineering)
Time: 3 Hours Max. Marks: 75
Note: This question paper contains two parts A and B.
Part A is compulsory which carries 25 marks. Answer all questions in Part A.
Part B consists of 5 Units. Answer any one full question from each unit.
Each question carries 10 marks and may have a, b, c as sub questions.
PART- A
(25 Marks)
1.a) Define Graph, Tree, Basic Cut set and Basic Tie set. Illustrate with an example.
[2]
b) Explain Active elements in detail. [3]
c) Derive the relation between voltage and current in a series connected RL Circuits.
[2]
d) Draw a power triangle in series connected RLC networks. [3]
e) Derive the relation between RMS and maximum value. [2]
f) Define form factor and peak factor. [3]
g) Define characteristic impedance. [2]
h) Define image and iterative impedance. [3]
i) Draw and explain T section network. [2]
j) Explain about LC Filters. [3]
PART-B
(50 Marks)
2.a) What is an electric circuit? What is a magnetic circuit? Make a comparison
between electric circuit and magnetic circuit.
b) Coil 1 of a pair of coupled coils has a continuous current of 5A, and the
corresponding fluxes ϕ11 and ϕ12 are 0.2 and 0.4 mWb respectively. If the turns
are N1 = 500 and N2 = 1500, find L1, L2, M and k. [5+5]
OR
3.a) For the network shown in below Figure 1 find Zab and Io.
Figure: 1
WWW.MANARESULTS.CO.IN
b) Find the input impedance of the circuit shown in Figure 2. Assume that the circuit
operates at ω = 50 rad/s. [5+5]
Figure: 2
4.a) Obtain the current locus of a fixed resistance and a variable capacitance.
b) Given a series RLC circuit with R = 10 ohms, L = 1 mH and C = 1 μF is
connected across a sinusoidal source of 20 V with variable frequency. Find: i) The
resonant frequency ii) Q factor of the circuit at resonant frequency iii) Half power
frequencies [5+5]
OR
5.a) Derive and draw the response of a series RLC circuit for step input.
b) An impedance Z1 = 10 + j10 Ω is connected in parallel with another impedance of
resistance 8.5 Ω and a variable capacitance connected in series. Find C such that
the circuit is in resonance at 5 KHz. [5+5]
6. A series-connected RLC circuit has R = 4 and L = 25 mH:
a) Calculate the value of C that will produce a quality factor of 50.
b) Find ω1, ω2, and B.
c) Determine the average power dissipated at ω = ω0, ω1, ω2. Take Vm = 100 V.
[3+3+4]
OR
7.a) Obtain the current locus of a series circuit having a fixed resistance and a variable
inductance.
b) Given a series RLC circuit with R = 100 ohms, L = 0.5 H and C = 40 μF,
Calculate the resonant, lower and upper half – power frequencies. [5+5]
8. Explain clearly the terms:
a) Characteristic Impedance and
b) Image Transfer Constant. [5+5]
OR
9.a) Define Hybrid parameters of a Two Port network. Establish the relation between
Hybrid Parameters and ABCD Parameters.
b) A symmetrical T-section has an inductance of 0.47H in each series arm and a
300 μF capacitor in the shunt arm.
i) Find the characteristic impedance at frequencies of 50 Hz and 100 Hz.
ii) If the T-section is terminated in the characteristic impedance, find the ratio of
load current to input current at both the frequencies. [5+5]
WWW.MANARESULTS.CO.IN
10.a) What is a high pass filter? In what respects it is different from a low pass filter?
b) Derive the equations to find the inductances and capacitances of a constant K high
pass filter. [5+5]
OR
11.a) What is an LC immittance function? State the properties of such functions.
b) Design a constant ‘K’ T-section low pass filter having cutoff frequency of 2 kHz
and nominal characteristic impedance of 600 ohms. [5+5]
---oo0oo---
WWW.MANARESULTS.CO.IN
