Scribd
Upload
226 views2 pages

Painting Inspection Test Plan

This document is an inspection and test plan for painting. It outlines 5 activities to be inspected before, during, and after surface preparation and paint application. Each activity lists the inspection method, applicable standards, acceptance criteria, who will verify inspections, and whether the client will conduct their own inspections. Inspections include checking surface cleanliness, abrasives, rust grade, paint thickness, bond strength, and porosity.

Uploaded by

daha333
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
226 views2 pages

Painting Inspection Test Plan

This document is an inspection and test plan for painting. It outlines 5 activities to be inspected before, during, and after surface preparation and paint application. Each activity lists the inspection method, applicable standards, acceptance criteria, who will verify inspections, and whether the client will conduct their own inspections. Inspections include checking surface cleanliness, abrasives, rust grade, paint thickness, bond strength, and porosity.

Uploaded by

daha333
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Doc.

INS/AH/2017

Page
INSPECTA MIDDLE EAST No.
Page 1 of 2

Rev. 0

INSPECTION AND TEST PLAN

FOR PAINTING

ITP

Owner :
Job No :
Document No:

Revision Date Issued by Checked Approved

Page 1 of 2
Doc. INS/AH/2017

Page
INSPECTA MIDDLE EAST No.
Page 2 of 2

Rev. 0

Act Description of of Q/C method Standard and Acceptance Verifying Cont. Client
No Q/ C Activity specification criteria Dotcom. Q/C Q/C
1 Before Surface Preparation

1.1 visual Free from weld Spec no H M


Steel work spatter, sharp edges
and contamination
1.2 Abrasive Lab analysis ISO 11126- Table3&4 H R
ISO11127 SPX
ASTM D4940
1.3 Oil leakage from compressor White Rag ASTM D4285 Oil free H R
1.4 Pressure at nozzle Hypodermic 7 bar H R
Needle gauge
1.5 Rust grade visual ISO 8501-1,2 H R
1.6 Airless pressure ratio Min 1:45 H R
1.7 Oil and grease Water break test Oil free H M
2 During surface preparation

2.1 Climatic condition Sling hygrometer ISO 8502-4 RH < 85% H R


and thermometer
S.T-D.P.T >3ºC
S.T< 47ºC
3 After Surface preparation

3.1 Preparation grade Visually ISO 8501-1,2 H R


3.2 Anchor Pattern Testex tape ASTM D4417 40-75 MICRONS H R
3.3 Salt contamination Besle test ISO8502-6,9 Max 50 mg/m2 H R
Dust On Substrate Pressure sensitive ISO 8502-3 Rating No-2 H R
tape
Climatic condition Sling hygrometer ISO 8502-4 RH < 85% H R
and thermometer
S.T-D.P. T >3ºC
S. T< 47ºC
4 Paint Application

Wet film thickness Comb gauge ASTM D4414 TDS H R

Dry Film Thickness Eddy current SSPC-PA 2 Specified DFT H W


method
5 Final test

5.1 Bond strength Pull off ASTM D4541 3 MPa H W


5.2 Porosity tests Wet sponge ASTM D 5I62 Min 3 points in m2 H W

INSPECTION CLASSIFICATION MARK –UP CODES

H= Hold Inspection and signature required before further operation can progress
W= Full Witness inspection –physical inspection for compliance, approved
R = Review check reports test sheet etc…for accuracy and authenticity
M= Monitor spot check /inspection for compliance

Page 2 of 2

You might also like