de

en

fr

es

pt

es

pt

Instructions for use for ENA Micro 1

ru

KE For your safety: read and understand manual before use.

Table of contents

Your ENA Micro 1

IMPORTANT SAFEGUARDS 4
Control elements 8
1  Preparing and using for the first time 10
Setting up the machine......................................................................................................................................... 10
Filling the bean container..................................................................................................................................... 10
First-time use........................................................................................................................................................... 10
First-time use with filter cartridge activation.................................................................................................... 10
First-time use without filter cartridge activation............................................................................................... 11
Adjusting the grinder..............................................................................................................................................12
Filling the water tank..............................................................................................................................................12
Determining the water hardness..........................................................................................................................12
2 Preparation 13
Ristretto, espresso and coffee...............................................................................................................................13
Permanently setting the amount of water for the cup size.............................................................................13
Ground coffee.......................................................................................................................................................... 14
3  Daily operation 14
Switching on the machine.................................................................................................................................... 14
Daily maintenance.................................................................................................................................................. 14
Switching off the machine.....................................................................................................................................15
4  Permanent settings in programming mode 15
Inserting and activating the filter.........................................................................................................................15
Setting the water hardness....................................................................................................................................15
5 Maintenance 16
Cleaning the machine............................................................................................................................................ 16
Descaling the machine ..........................................................................................................................................17
Changing the filter................................................................................................................................................. 18
Descaling the water tank....................................................................................................................................... 19
Cleaning the bean container................................................................................................................................ 19
6  Messages on symbol display 20
7 Troubleshooting 21
8  Transport and environmentally friendly disposal 22
Transport / Emptying the system........................................................................................................................22
Disposal....................................................................................................................................................................22
9  Technical data 22
10 Index 23
11  JURA contact details / Legal information 25

2
 de
Table of contents

en

fr

it

Symbol description en

Warnings
This is the safety alert symbol. lt is used to alert you to potential personal injury
J hazards. Obey all safety messages that follow this symbol to avoid possible injury or
death.
J DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or es
serious injury.
J WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
J CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury. pt

Symbols used
T Prompt to take action. This symbol means that you are being prompted to perform
some action.
E Information and tips to make it even easier to use your ENA.
ru

3
IMPORTANT SAFEGUARDS

IMPORTANT SAFEGUARDS

Follow the basic safety When using electrical appliances, basic safety precautions shall always
precautions be followed, to reduce the risk of fire, electric shock, and/or injury to
persons, including the following:
ZZ Read all instructions.
ZZ Do not touch hot surfaces. Use handles or knobs.
ZZ To protect against fire, electric shock and injury to persons, do not
immerse power cord, plugs, or body of machine in water or other
liquid.
ZZ Close supervision is necessary when any appliance is used by or
near children.
ZZ Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts, and before cleaning the
appliance.
ZZ Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service facil-
ity for examination, repair or adjustment.
ZZ The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or injury
to persons.
ZZ Do not use outdoors.
ZZ Do not let the cord hang over the edge of a table or counter, or
touch hot surfaces.
ZZ Do not place on or near a hot gas or electric burner, or in a heated
oven.
ZZ To disconnect, turn any control to ‘OFF’ then remove plug from
wall outlet.
ZZ Do not use appliance for other than intended use.
ZZ Use extreme caution when dispensing hot steam, hot water or
hot coffee.
ZZ For household use only.

SAVE THESE INSTRUCTIONS.

Pass them on to any subsequent user.

4
 de
IMPORTANT SAFEGUARDS

Intended use The appliance is designed and intended for household use only. It shall
only be used for coffee preparation, according to these instructions. Use
for any other purpose will be deemed improper. JURA Elektroapparate
AG cannot accept any responsibility for the consequences of improper en
use.

People, including children, who

ZZ do not have the physical, sensory or mental capabilities to use the
appliance safely or
ZZ are inexperienced or lack knowledge in how to use the appliance fr
safely
must be supervised by a responsible person when using it, or must be
instructed in how to use it correctly.

Special power cord set ZZ The power cord is provided to reduce the risk resulting from
instructions becoming entangled in or tripping over a long cord.
it
ZZ The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or
tripped over.
ZZ This appliance has a 3-pin grounded plug.
ZZ Do not modify the plug in any way.

Do NOT use extension cords. en

If the user chooses to use an extension cord,
ZZ the marked electrical rating of the extension cord shall be at least
as great as the electrical rating of the appliance, and
ZZ if the appliance is of the grounded type, the extension cord shall
be a grounding type 3-wire cord, and
ZZ the longer cord shall be arranged so that it will not drape over the es
counter top or tabletop where it can be pulled on by children or
tripped over.

J WARNING To reduce the risk of fire or electric shock, DO NOT remove any service
covers. DO NOT modify the appliance in any way that is not described
in these instructions. NO user serviceable parts included. Repair MUST
pt
be done by authorized personnel only.

In the event of signs of damage, for example if there is a smell of

burning, unplug the machine immediately from outlet and contact
JURA customer service.

ru

5
IMPORTANT SAFEGUARDS

J CAUTION This appliance is for household use. Any servicing other than cleaning
and user maintenance shall be performed by an authorized service rep-
resentative:
ZZ Do not immerse base in water or try to disassemble.
ZZ Do not put the appliance or any individual parts in the dishwasher.
ZZ Check voltage to be sure that the voltage indicated on the name
plate complies with your voltage. The name plate is located on
the underside of the appliance.
ZZ Never use warm or hot water to fill the water container. Use cold
water only.
ZZ Keep your hands and the cord away from hot parts of the
appliance during operation.

NOTICE ZZ Never clean with scouring powders or hard implements.

ZZ Ensure that the ventilation slots are not covered.
ZZ Never pull out the drip tray during the brewing process. Only pull
the drip tray when the display instructs you or when the appliance
is ready for use.

NEVER DO ZZ Never fill instant coffee, chocolate mix etc. into the bean container
(or you will void your or ground coffee funnel (filler funnel for ground coffee). It will
warranty protection): damage the functioning of the brewing chamber.
ZZ Never fill sugar coated coffee beans into the bean container. In
case of doubt, call your dealer.
ZZ Never fill anything other than coffee beans into the bean
container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
ZZ Never fill frozen beans into the bean container. If you store beans
in the freezer, let them thaw 3 to 4 hours before filling them into
the bean container.
ZZ Never fill anything but fresh, cold and clean water into the water
tank, except when decalcifying.
ZZ Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
ZZ Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.

6
 de

en

fr

it

– intentionally blank –
en

es

pt

ru

7
Control elements

Control elements

1
5

8
J HOT
3

1 Water tank 5 Bean container with aroma preservation cover

2 Power cord (back of the machine) 6 Ventilation slots
3 Coffee grounds container 7 On/Off button
4 Drip tray 8 Height-adjustable coffee spout
9 Cup platform

8
 de
Control elements

en

1 3

4
2

fr

1 Cover for powder chute for ground coffee 3 Cover cap for grinder adjustment switch
2 Powder chute for ground coffee 4 Grinder adjustment switch

it

1 en

1 Symbol display es
; Coffee strength ‘normal’
& Descaling symbol _ Coffee strength ‘strong’
! Filter symbol Y Ristretto symbol
L Cleaning symbol < Espresso symbol
M Water Tank symbol > Coffee symbol
v Ground Coffee symbol
? Coffee Grounds Container symbol pt

ru

9
1  Preparing and using for the first time

1  Preparing and using for the First-time use

first time When using the machine for the first time, you can
choose whether you want to operate ENA with or
This chapter provides you with the information without the CLEARYL Blue filter cartridge. If the
you need to use your ENA without any problems. water hardness is 10 °dH or more, we recommend
You will prepare your ENA step-by-step to enjoy using the filter cartridge. If you do not know the
your first perfect cup of coffee. hardness of your water, you can find this out first
EE Visit us on the internet. On the JURA (see Chapter 1 ‘Preparing and using for the first
website (www.jura.com) you will find time – Determining the water hardness’).
interesting and up-to-date information on
EE The On/Off button also acts as a power
your ENA and every aspect of coffee.
switch. When the ENA is switched off, the
machine does not consume standby energy.
Setting up the machine
When setting up your ENA, please note the J WARNING
following: If the machine is operated with a defective power
UU Place the machine on a horizontal surface that cord, there is a danger of potentially fatal electric
is not sensitive to water. shock.
UU Choose a spot for your ENA which protects the T  Never use a machine which is damaged.
machine against overheating. Ensure that the T  Never use a machine which has a defective
ventilation slots are not covered. power cord.

Precondition: Bean container is filled.

T Insert the power plug into a power socket.
Q  T  Press the On/Off button to switch the
machine on.
The Descaling symbol & and the Filter
symbol ! are lit up.

EE Now decide whether you want to operate

your ENA with or without a CLEARYL Blue
Filling the bean container filter cartridge.

NOTICE
Coffee beans which have been treated with
First-time use with filter cartridge
additives (e.g. sugar), ground coffee or freeze-dried
activation
coffee will damage the grinder.
T  Only use roasted, untreated coffee beans to !  T  Touch the Filter symbol.
fill the bean container. The Water Tank symbol M lights up.
T Remove the water tank.
T Remove the aroma preservation cover of the T Open the filter holder.
bean container.
T Remove any dirt or foreign objects from
inside the bean container.
T Fill the bean container with coffee beans.
T Close the bean container.
10
 de
1  Preparing and using for the first time

T Insert the filter cartridge into the water tank, hardness. The following water hardness settings
exerting slight pressure. are available:
Water hardness Symbol(s) shown in display
Level 1: 1 symbol illuminated en
1–15 °dH Y
Level 2: 2 symbols illuminated
16–23 °dH Y<
Level 3: 3 symbols illuminated
24–30 °dH Y<>
fr
&  T  Touch the Descaling symbol.
T Close the filter holder. It will click into place The Y, < and & symbols light up.
audibly. T Touch the Y, < or > symbol to set the
water hardness, e.g. symbol Y for ‘level 1’.
EE After two months, the filter will cease to
The Y and & symbols light up.
work. Set the date on the date plate on the
&  T  Touch the Descaling symbol.
filter holder in the water tank. it
The Water Tank symbol M lights up.
T Fill the water tank with fresh, cold water and T Place a receptacle under the coffee spout.
reinsert it. T Remove the water tank.
The Filter symbol ! lights up. T Fill the water tank with fresh, cold water and
!  T  Touch the Filter symbol. reinsert it.
The Y, <, > and ! symbols flash. The filter
is rinsed and the water flows directly into the en
drip tray.
Rinsing of the filter stops automatically. The
machine heats up.
The Y, < and > symbols flash. The
machine is rinsed, water flows out of the
coffee spout. The rinse stops automatically. es
The Coffee Grounds Container symbol ?
lights up. The Y, < and > symbols flash. The system
T Empty the coffee grounds container and fills with water and the water flows directly
drip tray and rinse with warm water. into the drip tray.
T Reinsert the coffee grounds container and The operation stops automatically. The
the drip tray. machine heats up.
The Ristretto Y, Espresso < and Coffee > The Y, < and > symbols flash. The pt
symbols and the symbol for ‘strong’ coffee machine is rinsed, water flows out of the
strength _ light up. Your ENA is ready for coffee spout. The rinse stops automatically.
use. The Ristretto Y, Espresso < and Coffee >
symbols and the symbol for ‘strong’ coffee
strength _ light up. Your ENA is ready for
First-time use without filter cartridge use. ru
activation
If you do not want to use the CLEARYL filter
cartridge Blue, you will need to set the water
11
1  Preparing and using for the first time

Adjusting the grinder Filling the water tank

You can adjust the grinder on a continuous scale to Daily maintenance of the machine and hygiene
suit the degree of roast of your coffee. when handling coffee and water are key to a
perfect coffee result in the cup every time. You
NOTICE should therefore change the water daily.
If you adjust the consistency of grind when the
grinder is not operating, the grinding wheel could NOTICE
be damaged. Milk, sparkling mineral water or other liquids can
T  Only adjust the consistency of grind when damage the water tank or the machine.
the grinder is running. T  Only fill the water tank with fresh, cold water.

T Remove the water tank and rinse with cold

EE For a coarser consistency of grind, turn the water.
switch to the left, for a finer grind, turn it to
the right.

The consistency of grind is correct if the coffee

flows regularly from the coffee spout. In addition a
fine, thick crema forms.
Example: Change the consistency of grind during
the preparation of a ‘strong’ espresso.
T Place a cup under the coffee spout.
T Open the cover of the grinder adjustment T Fill the water tank with fresh, cold water and
switch. reinsert it.

Determining the water hardness

You can find out what the water hardness is by
using the Aquadur® test strip supplied as standard.
T Hold the test strip briefly (for one second)
under running water.
T Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of
_  T  Touch the symbol for ‘strong’ coffee
water hardness from the discoloration of the
strength.
Aquadur® test strip and the description on
The ‘strong’ _ symbol lights up.
the packaging.
<  T  Touch the Espresso symbol to start
preparation.
T Turn the grinder adjustment switch to the
desired position while the grinder is
running.
The preset amount of water flows into the
cup. Preparation stops automatically.

The water hardness can now be set.

12
 de
2 Preparation

2 Preparation Ristretto, espresso and coffee

Ristretto Y, espresso < and coffee > are all
J WARNING prepared following this model.
en
Hot Coffee can cause scalding. Scalding is a serious Example: Proceed as follows to prepare one coffee.
burn. Precondition: Your ENA is ready for use.
T  Use extreme care when handling hot liquid. T Place a cup under the coffee spout.
T  Allow liquid to cool down before drinking. >  T  Touch the Coffee symbol to start prepara-
T  In the event of scalding, rinse affected area tion.
with cold water and seek medical attention. The coffee symbol > and coffee strength
T  Keep children AWAY. fr
symbol (; or _) flash, the preset amount of
water flows into the cup.
EE While a specialty coffee is being prepared, Preparation stops automatically. Your ENA is
you can stop preparation at any time. Simply once more ready for use.
touch the symbol for the product in
question. Permanently setting the amount of water
EE Before and during the grinding operation it
for the cup size
you can select the coffee strength for
ristretto Y, espresso < and coffee >: It is easy to make permanent settings for the
‘normal’ (;), ‘strong’ (_). amount of water for all specialty coffees according
to the cup size. Adjust the amount once as shown
The machine always uses the preset amount of in the following example. Every time you prepare a
water for the type of coffee in question. You can drink in the future, this amount of water will be
change this setting (see Chapter 2 ‘Preparation –
en
dispensed.
Permanently setting the amount of water for the
Example: Permanently adjust the amount of
cup size’).
espresso to the cup size.
Your ENA features an energy-saving mode: Soon Precondition: Your ENA is ready for use.
after the last preparation, the ENA stops heating T Place a cup under the dual spout.
up. To indicate that the machine is in energy- <  T  Touch the Espresso symbol for about 3 es
saving mode, after about 5 minutes the brightness seconds until the Ristretto Y and coffee >
of all the symbols is reduced. The ENA must heat symbols appear again.
back up before the next preparation. <  T  Release the Espresso symbol.
The espresso is prepared. The Espresso
Coffee tastes best served hot. A cold porcelain cup
symbol < and coffee strength symbol (; or
cools the beverage – and impairs the taste. We
_) are flashing.
therefore recommend prewarming the cups. The pt
<  T  Touch the Espresso symbol as soon as there
full coffee aroma can develop only in prewarmed
is enough espresso in the cup.
cups. You can purchase a JURA cup warmer from
Preparation stops. The amount of water for
your specialized dealer.
one espresso is permanently stored.
The Espresso symbol < and coffee strength
symbol (; or _) flash until the machine is
ready for use again. ru
EE You can alter this setting at any time by
repeating the above procedure.

13
3  Daily operation

Ground coffee >  T  Touch the Coffee symbol to start prepara-

tion.
You can choose to use a second coffee variety, for
The Coffee symbol > flashes, the preset
example decaffeinated coffee, with the powder
amount of water flows into the cup.
chute for ground coffee.
Preparation stops automatically. Your ENA is
EE Use ground coffee which is not ground too once more ready for use.
finely. Very fine coffee can block up the
system so that the coffee only comes out in
drips.
3  Daily operation
EE Never add more than one level measuring
spoon of ground coffee.
Switching on the machine
EE The desired specialty coffee must be
prepared within approximately one minute Daily maintenance of the machine and hygiene
after filling with the ground coffee. when handling coffee and water are key to a
Otherwise the ENA stops the operation and perfect coffee result in the cup every time. You
is once more ready for use. should therefore change the water daily.
EE If you did not add a sufficient amount of When the machine is switched on, it will automa-
ground coffee, the Y, <, > and v symbols tically rinse.
flash and the ENA stops the operation. T Place a receptacle under the coffee spout.
Q  T  Press the On/Off button to switch the
All specialty coffees with ground coffee are
machine on.
prepared following this model.
The Y, < and > symbols flash, the
Example: Prepare a cup of coffee using ground machine heats up.
coffee. The machine is rinsed, water flows out of the
Precondition: Your ENA is ready for use. coffee spout. The rinse stops automatically.
T Place a cup under the coffee spout. Your ENA is ready for use.
T Open the powder chute for ground coffee.
The Ground Coffee symbol v lights up.
T Place the filler funnel for ground coffee on Daily maintenance
the powder chute.
To ensure that you get many years of reliable
service out of your ENA and to guarantee the
optimum coffee quality, the machine requires daily
maintenance.
T Remove the drip tray.
T Empty the coffee grounds container and
drip tray and rinse with warm water.
T Reinsert the coffee grounds container and
the drip tray.
T Rinse the water tank with clean water.
T Place one level measuring spoon of ground
T Wipe the surface of the machine with a
coffee into the filler funnel.
clean, soft, damp cloth (e.g. microfiber
T Close the powder chute for ground coffee.
cloth).
The Y, <, > and v symbols flash.
The Y, < and > symbols light up.

14
 de
4  Permanent settings in programming mode

Switching off the machine T Insert the filter cartridge into the water tank,
exerting slight pressure.
When the ENA is switched off, the system is
automatically rinsed if a specialty coffee has been
en
prepared.
T Place a receptacle under the coffee spout.
Q  T  Press the On/Off button.
The Y, < and > symbols flash. The
machine is rinsed, water flows out of the
coffee spout.
The rinse stops automatically. Your ENA is fr
switched off.
T Close the filter holder. It will click into place
EE When the ENA is switched off with the On/ audibly.
Off button, the machine does not consume
EE After two months, the filter will cease to
standby energy.
work. Set the date on the date plate on the
EE If no action is performed on the machine for
2 hours, the ENA will automatically switch
filter holder in the water tank. it
off to save energy. T Fill the water tank with fresh, cold water and
reinsert it.
The Coffee Grounds Container symbol ?
lights up.
4  Permanent settings in T Empty the drip tray and coffee grounds
programming mode container and reinsert them. en
The Filter symbol ! lights up.
Inserting and activating the filter !  T  Touch the Filter symbol to start rinsing of
the filter
Your ENA no longer has to be descaled if you are The Y, <, > and ! symbols flash. The filter
using the CLEARYL Blue filter cartridge. If you did is rinsed.
not activate the filter cartridge the first time you Rinsing of the filter stops automatically. The es
used the machine, you can do this now as follows. Coffee Grounds Container symbol ? lights
up.
EE Perform the ‘inserting the filter’ operation
T Empty the drip tray and coffee grounds
without any interruptions. This will ensure
container and reinsert them.
that your ENA always produces its best.
The Y, < and > symbols flash, the
machine heats up. Your ENA is once more
Precondition: Your ENA is ready for use. ready for use. pt
T Touch the ; and _ symbols for approxi-
mately 2 seconds.
The ;, _, & and L symbols light up brightly. Setting the water hardness
!  T  Touch the Filter symbol for approximately EE If you are using the CLEARYL Blue filter
2 seconds. cartridge and have activated it, there is no
The Water Tank symbol M lights up. need to set the water hardness. ru
T Remove the water tank.
T Open the filter holder. The harder the water is, the more frequently the
ENA needs to be descaled. It is therefore important
to adjust the water hardness.
15
5 Maintenance

The following water hardness settings are available: Your ENA has the following integrated mainte-
Water hardness Symbol(s) shown in display nance programs:
Level 1: 1 symbol illuminated UU Cleaning the machine
1–15 °dH Y UU Descaling the machine

Level 2: 2 symbols illuminated UU Changing the filter

16–23 °dH Y<
Level 3: 3 symbols illuminated Cleaning the machine
24–30 °dH Y<>
After 180 preparations or 80 switch-on rinses, the
Example: Change the water hardness setting from ENA will prompt you to clean it.
‘level 2’ (Y <) to ‘level 3’ (Y < >). J WARNING
Precondition: Your ENA is ready for use.
T Touch the ; and _ symbols for approxi- Non-recommended (e.g. liquid) cleaning agents
mately 2 seconds. may contain substances that could damage the
The ;, _, & and L symbols light up brightly. machine or leave residues.
&  T  Briefly touch the Descaling symbol. T  Use only original JURA cleaning tablets.
The &, Y and < symbols light up. These are specially formulated for your
>  T  Touch the Coffee symbol. machine.
The &, Y, < and > symbols light up. J WARNING
&  T  Touch the Descaling symbol to confirm that
you want to set the water hardness to Harmful and irritating cleaning agent. Harmful if
‘level 3’. swallowed. Irritating to eyes and skin.
Your ENA is once more ready for use. T  Keep children AWAY.
T  Avoid contact with skin and eyes.
T  Avoid generation of dust. Do not inhale dust.
T  After contact with skin, wash immediately
5 Maintenance with plenty of water. In case of skin irritation,
seek medical advice.
J WARNING T  After eye contact, immediately flush eyes
with plenty of water and seek medical
Use of maintenance products that are harmful to
advice.
health and discharge of liquids during mainte-
T  If swallowed, rinse mouth immediately and
nance program. Harmful if swallowed. Irritating to
drink large quantities of water. Do not
eyes and skin.
induce vomiting. Seek medical advice
T  Keep children AWAY.
immediately and show label.
T  Keep children away from the machine while
it is performing a maintenance program.
T  Avoid contact with skin and eyes. EE The cleaning program lasts approximately
T  Avoid generation of dust. Do not inhale dust. 15 minutes.
T  When using do not eat or drink. EE Do not interrupt the cleaning program. The
T  Keep maintenance products away from food, quality of cleaning will be impaired if you do
drink and animal food. so.
T  Keep container tightly closed and dry. Keep EE JURA cleaning tablets are available from
in a cool place. specialized dealers.

16
 de
5 Maintenance

Precondition: Your ENA is ready for use. The Descaling the machine

Cleaning symbol L lights up.
L  T  Touch the Cleaning symbol for approxi- The ENA builds up deposits of limescale over time
and automatically prompts you to descale it when
mately 2 seconds. en
The Coffee Grounds Container symbol ? necessary. The degree of calcification depends on
lights up. the hardness of your water.
T Empty the drip tray and coffee grounds J WARNING
container and reinsert them.
Non-recommended descaling agents (e.g. vinegar)
The Cleaning symbol L lights up.
may contain substances that could damage the
T Place a receptacle under the coffee spout.
machine or leave residues. fr
L  T  Touch the Cleaning symbol.
T  Use only original JURA descaling tablets.
The Y, <, > and L symbols flash, water
These are specially formulated for your
flows out of the coffee spout.
machine.
The operation is interrupted, the Ground
Coffee symbol v lights up. J WARNING
T Open the powder chute for ground coffee
Harmful and irritating descaling agent. Harmful if
and drop in a JURA cleaning tablet. it
swallowed. Irritating to eyes and skin.
T  Keep children AWAY.
T  Avoid contact with skin and eyes.
T  Avoid generation of dust. Do not inhale dust.
T  After contact with skin, wash immediately
with plenty of water. In case of skin irritation,
seek medical advice. en
T  After eye contact, immediately flush eyes
with plenty of water. Remove contact lenses.
Seek medical advice.
T Close the powder chute for ground coffee.
T  If swallowed, rinse mouth immediately and
The Cleaning symbol L lights up.
drink large quantities of water. Do not
L  T  Touch the Cleaning symbol.
induce vomiting. Seek medical advice es
The Y, <, > and L symbols flash, water
immediately and show label.
flows out of the coffee spout several times.
The operation is interrupted, the Coffee NOTICE
Grounds Container symbol ? lights up. If the descaling operation is interrupted, there may
T Empty the drip tray and coffee grounds be damage to the machine.
container and reinsert them. T  Allow the descaling program to run to the
The Y, < and > symbols flash. The end. pt
machine heats up.
Your ENA is once more ready for use. EE The descaling program lasts approximately
Cleaning the machine without a prompt: You can 40 minutes.
initiate the 'Cleaning the machine' operation EE JURA descaling tablets are available from
manually at any time as long as the machine is specialized dealers.
ready for use. Touch the ; and _ symbols at the EE If you use a CLEARYL Blue filter cartridge and ru
same time for approximately 2 seconds. The ;, this is activated, you will not be prompted to
_, L and & or ! symbols light up brightly. descale.
Continue with the first prompt (indicated by T) as
described in this section.
17
5 Maintenance

EE If the descaling agent comes into contact &  T  Touch the Descaling symbol.
with sensitive surfaces (e.g. marble), damage The Y, <, > and & symbols flash and water
cannot be ruled out. Clean up any splashes flows directly into the drip tray.
immediately. The Y, < and > symbols flash and water
flows out of the coffee spout.
Precondition: Your ENA is ready for use. The
The operation is interrupted, the Coffee
Descaling symbol & lights up.
Grounds Container symbol ? lights up.
&  T  Touch the Descaling symbol for approxi-
T Empty the drip tray and coffee grounds
mately 2 seconds.
container and reinsert them.
The Coffee Grounds Container symbol ?
Your ENA is once more ready for use.
lights up.
T Empty the drip tray and coffee grounds EE If the descaling operation stops unexpec-
container and reinsert them. tedly, rinse the water tank thoroughly.
The Water Tank symbol M flashes.
T Remove and empty the water tank. Descaling the machine without a prompt: You
T Completely dissolve the contents of one can initiate the 'Descaling the machine' operation
blister (three JURA descaling tablets) in a manually at any time as long as the machine is
receptacle holding 17 oz (500 ml) of water. ready for use. Touch the ; and _ symbols at the
This may take several minutes. same time for approximately 2 seconds. The ;,
_, L and & symbols light up brightly. Continue
with the first prompt (indicated by T) as described
in this section.

Changing the filter

EE After 2000 oz (60 liters) of water have flowed
through, the filter will cease to work. Your
ENA will automatically prompt you to
T Pour the solution into the empty water tank change the filter.
and reinsert the tank. EE After two months, the filter will cease to
The Descaling symbol & lights up. work. Set the date on the date plate on the
&  T  Touch the Descaling symbol. filter holder in the water tank.
The Y, <, > and & symbols flash and water EE If the CLEARYL Blue filter cartridge is not
flows directly into the drip tray. activated in programming mode, you will
The operation is interrupted, the Coffee not be prompted to change the filter.
Grounds Container symbol ? flashes.
T Empty the drip tray and coffee grounds
container and reinsert them. Precondition: Your ENA is ready for use. The Filter
The Water Tank symbol M lights up. symbol ! lights up.
T Remove the water tank and rinse !  T  Touch the Filter symbol for approximately 2
thoroughly. seconds.
T Fill the water tank with fresh, cold water and The Water Tank symbol M lights up.
reinsert it. T Remove the water tank.
The Descaling symbol & lights up. T Open the filter holder and remove the old
filter cartridge.

18
 de
5 Maintenance

T Insert a new filter cartridge into the water Descaling the water tank
tank, exerting slight pressure.
Limescale deposits may form in the water tank. To
ensure correct function of the machine, descale
en
the water tank from time to time.
T Remove the water tank.
T If you use a CLEARYL Blue filter cartridge,
remove it.
T Descale the tank with a mild conventional
descaling agent in accordance with the
manufacturer's instructions. fr
T Rinse the water tank thoroughly.
T Close the filter holder. It will click into place
T If you use a CLEARYL Blue filter cartridge,
audibly.
reinsert it.
EE After two months, the filter will cease to T Fill the water tank with fresh, cold water and
work. Set the date on the date plate on the reinsert it.
filter holder in the water tank. it
Cleaning the bean container
T Fill the water tank with fresh, cold water and
reinsert it. Coffee beans may be covered with a slight oil film
The Coffee Grounds Container symbol ? which remains on the walls of the bean container.
lights up. These traces may negatively affect the coffee
T Empty the drip tray and coffee grounds result. For this reason clean the bean container
container and reinsert them. from time to time. en
The Filter symbol ! lights up. Q  T  Press the On/Off button to switch the
!  T  Touch the Filter symbol to start rinsing of machine off.
the filter. T Disconnect the power plug.
The Y, <, > and ! symbols flash. The filter T Remove the bean container cover.
is rinsed. Water flows directly into the drip T Remove the coffee beans with a vacuum
tray. cleaner. es
Rinsing of the filter stops automatically. The T Clean the bean container with a soft, dry
Coffee Grounds Container symbol ? lights cloth.
up. T Fill the bean container with fresh coffee
T Empty the drip tray and coffee grounds beans, then close the bean container cover.
container and reinsert them.
The machine heats up. Your ENA is once
more ready for use. pt

Changing the filter without a prompt: If the filter

is activated, you can initiate the 'Changing the
filter' operation manually at any time as long as
the machine is ready for use. Touch the ; and _
symbols at the same time for approximately 2
ru
seconds. The ;, _, L and ! symbols light up
brightly. Continue with the first prompt (indicated
by T) as described in this section.

19
6  Messages on symbol display

6  Messages on symbol display

Message (Symbol(s) Cause/Result Action
shown in display)
The Water Tank symbol M The water tank is empty or not T Fill the water tank (see Chapter 1
lights up. correctly inserted. You cannot ‘Preparing and using for the first
prepare any products. time – Filling the water tank’).
T Insert the water tank.
The Coffee Grounds The coffee grounds container is T Empty the coffee grounds
Container symbol ? lights full. No specialty coffees can be container and the drip tray (see
up. prepared. Chapter 3 ‘Daily operation – Daily
maintenance’).
The Coffee Grounds The drip tray is not inserted T Insert the drip tray.
Container symbol ? flashes. correctly or is not inserted at all.
You cannot prepare any
products.
The Y, <, >, ; and _ The aroma preservation cover T Fit the aroma preservation cover
symbols flash. for the bean container is not correctly.
fitted or not fitted correctly.
The ;, _, L and & or ! You are in programming mode. T Touch the ; or _ symbol to exit
symbols light up brightly. programming mode. Your ENA is
once more ready for use.
The ENA is ready for use and The ENA is prompting you to T Perform cleaning (see Chapter 5
the Cleaning symbol L lights clean it. ‘Maintenance – Cleaning the
up. machine’).
The ENA is ready for use and The ENA is prompting you to T Perform descaling (see Chapter 5
the Descaling symbol & lights descale it. ‘Maintenance – Descaling the
up. machine ’).
The ENA is ready for use and After 2000 oz (60 liters) of water T Replace the CLEARYL Blue filter
the Filter symbol ! lights up. have flowed through the cartridge (see Chapter 5 ‘Mainte-
CLEARYL Blue filter cartridge, it nance – Changing the filter’).
will cease to work.
Preparing ground coffee: There is insufficient ground T The next time you prepare a
After ground coffee is added coffee in the machine; the ENA beverage, add more ground coffee
to the machine, the Y, <, > stops the operation. (see Chapter 2 ‘Preparation –
and v symbols flash briefly. Ground coffee’).

20
 de
7 Troubleshooting

7 Troubleshooting
Problem Cause/Result Action
Coffee only comes out in Coffee or ground coffee has en
T Set the grinder to a coarser setting or
drips when it is being been ground too finely and use coarser ground coffee (see Chapter 1
prepared. is blocking the system. ‘Preparing and using for the first time –
Adjusting the grinder’).
The Water Tank symbol M The water tank float is T Descale the water tank (see Chapter 5
lights up even though the trapped. ‘Maintenance – Descaling the water
tank is full. tank’). fr
The ; and _ symbols flash The system must be filled T Fill the water tank (see Chapter 1
alternately. with water. ‘Preparing and using for the first time –
Filling the water tank’).
T Touch the ; or _ symbol.
The system fills up with water.
it
Grinder is making a very loud There are foreign objects in T Contact customer support in your
noise. the grinder. country (see Chapter 11 ‘JURA contact
details / Legal information’).
When the ENA is switched If the machine was exposed T Warm the machine at room
on, the Cleaning symbol L to the cold for a long temperature.
flashes for 5 seconds. The period of time, heating is
machine then switches off. disabled for safety reasons. en

EE If you were unable to solve the problem,

contact customer support in your country
(see Chapter 11 ‘JURA contact details / Legal
information’).
es

pt

ru

21
8  Transport and environmentally friendly disposal

8  Transport and environmentally 9  Technical data

friendly disposal
Voltage 120 V ~, 60 Hz
Transport / Emptying the system Power 1450 W
Conformity mark
Keep the packaging for your ENA. It should be used
to protect the machine during transport.
Energy consumption approx. 4.0 Wh
In order to protect the ENA from frost during Energy Save Mode ‘on’
transport, the system must be emptied. (display symbols slightly
less bright)
Precondition: Your ENA is ready for use. Pump pressure Static, max. 15 bar
T Place a receptacle under the coffee spout.
Holding capacity of water 37.2 oz
T Touch the ; and _ symbols for approxi-
tank (without filter) (1.1 l)
mately 2 seconds.
The ;, _, L and & or ! symbols light up Holding capacity of bean 4.4 oz
brightly. container (125 g)
T Remove and empty the water tank. Holding capacity of approx. 9 servings
The <, > and M symbols light up. coffee grounds container
<  T  Touch the Espresso symbol Cord length Approx. 43.3 in.
Hot water will continue to flow until the (1.1 m)
system is empty. Weight Approx. 19.6 lb
The Water Tank symbol M lights up. (Approx. 8.9 kg)
Q  T  Press the On/Off button to switch the
Dimensions (W × H × D) 9.0 × 12.7 × 17.5 in.
machine off.
(23 × 32.3 × 44.5 cm)

Disposal Information for testers (repeat test in accordance

with DIN VDE 0701-0702): The central grounding
Please dispose of old machines in an environmen- point (CGP) is located on the underside of the
tally neutral way. machine, right next to the mains cable‘s connec-
H tion point.

Directives
The machine complies with the following
directives:
UU Standard UL 1082
UU Canadian Standard CSA C22.2 No. 64

22
 de
10 Index

10 Index

A Energy Save Mode 13 en

Addresses 25 Errors
Aroma preservation cover Troubleshooting 21
Bean container with aroma preservation cover Espresso 13
8 F
B Filling
Bean container Bean container 10
Water tank 12 fr
Bean container with aroma preservation cover
8 Filter
Cleaning 19 Changing 18
Filling 10 Inserting and activating the filter 15
Bus bar First-time use 10
Technical data 22 With filter cartridge activation 10
Button Without filter cartridge activation 11
it
On/Off button 8 G
C Ground coffee 14
Central grounding point 22 Powder chute for ground coffee 9
Cleaning Grounding point 22
Bean container 19 H
Machine 16 Height-adjustable coffee spout 8
CLEARYL Blue filter cartridge Hotline 25 en
Changing 18
Inserting and activating the filter 15
I
Important safeguards
Coffee 13
Safety 4
Coffee grounds container 8
Instant coffee
Coffee spout
Ground coffee 14
Height-adjustable coffee spout 8
Internet 10 es
Consistency of grind
Adjusting the grinder 12 J
Grinder adjustment switch 9 JURA
Contact details 25 Contact details 25
Cup platform 8 Internet 10
Customer support 25 website 10
D M
Machine pt
Descaling
Machine 17 Cleaning 16
Water tank 19 Descaling 17
Display Setting up 10
Symbol display 9 Switching off 15
Display, messages 20 Switching on 14
Disposal 22 Maintenance
Daily maintenance 14 ru
Drip tray 8
Maintenance 16
E Messages on display 20
Emptying the system 22

23
10 Index

P U
Permanently setting the water for the cup size Use, First-time 10
13 V
Permanent settings in programming mode 15 Ventilation slots 8
Powder chute
Powder chute for ground coffee 9 W
Power cord 8 Water hardness
Preparation 13 Determining the water hardness 12
Coffee 13 Setting the water hardness 15
Espresso 13 Water tank 8
Ground coffee 14 Descaling 19
Ristretto 13 Filling 12
Problems website 10
Troubleshooting 21
Programming mode 15
Setting the water hardness 15
R
Ristretto 13
S
Safety
Important safeguards 4
Settings
Permanent settings in programming mode
15
Setting up
Setting up the machine 10
Switching off 15
Switching on 14
Symbol
Cleaning 9
Coffee 9
Coffee Grounds Container 9
Coffee strength 9
Descaling 9
Espresso 9
Filter 9
Ground Coffee 9
Ristretto 9
Water Tank 9
Symbol description 3
Symbol display 9
Messages 20
T
Technical data 22
Tel 25
Transport 22
Troubleshooting 21

24