BLX

Wireless System

Online user guide for Shure BLX wireless system.

Version: 4 (2019-H)
 Shure Incorporated

Table of Contents
Tips to Improve Wireless System Performance 12
BLXWireless System 3
Getting Good Sound 13
IMPORTANT SAFETY INSTRUCTIONS 3 Correct Microphone Placement 13

Wearing the Headworn Microphone 13

System Components 4

Adjusting Gain 14
Quick Start Guide 4
BLX1 14
Features 6
BLX2 15
Front Panel 6
Batteries 15
Back Panel 7

BLX1 7 Wearing the Bodypack Transmitter 16

BLX2 8
Power Off 16
Single System Set Up 9
Removing and Installing Identification Caps 17
Setting Transmitter Group and Channel 10
Troubleshooting 17
Group (letter) 10

Channel (number) 10 Specifications 18

Multiple System Setup 11 Certifications 21

Manually Setting Receiver Group and Channel 12 Important Product Information 21

Group (letter) 12 LICENSING INFORMATION 22
Channel (number) 12 Information to the user 22

Australia Warning for Wireless 23

Locking and Unlocking Controls 12

Transmitter (lock/unlock) 12 Frequency Range and Transmitter Output Level 23

Receiver (lock/unlock) 12 Frequencies for European Countries 24

2/28
 Shure Incorporated

BLX
Wireless System

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance
with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in­
cluding amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace­
ment of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the
apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec­
tion.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
21. Operate this product within its specified operating temperature range.

3/28
 Shure Incorporated

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accom­
panying this unit.

WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.

System Components
Note: Your system comes with a combination of the following components.

• BLX1 Bodypack Transmitter

• BLX2 Handheld Transmitter (choice of SM58, BETA58A, or PG58)
• BLX4 Wireless Receiver
• BLX88 Dual Wireless Receiver
• PS24 Power Supply
• Lavalier microphone (choice of PG185, WL185 or WL93)
• Headworn microphone (choice of PG30, SM31FH or SM35)
• MX153 Earset microphone
• Instrument microphone (BETA98H/C)
• Guitar cable (WA302)

Quick Start Guide

1. 1. Connect receiver to power source.

2. Connect receiver to mixer or amplifier. Hold power button to turn on.

2. Press group button on receiver to perform a group scan.

4/28
 Shure Incorporated

3. 1. Install batteries and turn on transmitter.

2. On the transmitter, set the group and channel to match the receiver. The audio LED on the receiver should illu­
minate.

If setting up additional systems, leave the first transmitter and receiver on. For each additional receiver, manual­
ly set the group to match the first receiver. Note: The receiver will automatically perform a channel scan to find
an available frequency after the group has been selected. Set the transmitter frequency to match the receiver.

4. If sound is too faint or distorted, adjust the gain accordingly.

5/28
 Shure Incorporated

Features
Front Panel

BLX4

BLX88

① audio LED
Indicates strength of incoming audio signal: green for normal and red for overload.

② ready LED
6/28
 Shure Incorporated

Green light indicates system is ready for use and receiving transmitter signal.

③ LED Display
Displays group and channel setting.

④ group and channel Buttons

Scan: Push and release group button to scan for an open group and channel.
Manual: Push and hold group button to select a group. Push channel button to select a channel in the current group.

⑤ power Button
Push and hold to turn power on or off.

Back Panel

BLX4

BLX88

① DC Power Jack

② Adapter Cord Tie-Off

③ XLR microphone output jack (MIC out)

④ 6.35 mm (1/4") instrument level output jack (instrument out)

BLX1
① LED Indicator
Displays power and battery status (see Transmitter LED Indicators).

② power Switch
Toggles power on or off.

7/28
 Shure Incorporated

③ 4-Pin Microphone Input Jack (TA4 connector)

④ Antenna

⑤ group Button
Changes group setting.

⑥ LED Display
Displays group and channel setting.

⑦ channel Button
Changes channel setting.

⑧ Battery Compartment

⑨ Audio Gain Adjustment

Rotate to increase or decrease transmitter gain.

BLX2
① LED Indicator
Displays power and battery status (see Transmitter LED Indicators).

② power Button
Push to turn power on or off.

③ group Button
Changes group setting.

8/28
 Shure Incorporated

④ channel Button
Changes channel and gain setting.

⑤ LED Display
Displays group and channel setting.

⑥ Identification Cap

⑦ Battery Compartment

Transmitter LED Indicators

LED Indicator Status

Green Ready

Rapidly Flashing Red Controls locked

Solid Red Battery power low (less than 1 hour remaining*)

Flashing Red and shuts off Batteries dead (change batteries to power on transmitter)

*For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.

9/28
 Shure Incorporated

Single System Set Up

Before you begin, turn off all transmitters and turn on any equipment (other microphones or personal monitoring systems) that
could cause interference during the performance.

1. Press and release the group button on the receiver.

The receiver scans for the clearest group and channel.

Note: If you want to stop the scan, push the group button again.

2. Turn on transmitter and change the group and channel to match the receiver (See Setting Transmitter Group and Chan­
nel).

Once the system is set up, perform an audio check and adjust the gain if necessary.

Setting Transmitter Group and Channel

Transmitter group and channel must be manually set to match the receiver.

Group (letter)
1. Press and release the group button on the transmitter to activate the display. Press the group button again and the dis­
play flashes.
2. While the display is flashing, press the group button again to advance to the desired group setting.

Channel (number)
If channel needs to be changed, follow the same procedure using the channel button instead of the group button.

Note:

• When the group and channel correctly match the receiver, the ready LED on receiver illuminates.
• After manual setup, the transmitter alternately displays the group and channel setting for about two seconds.

10/28
 Shure Incorporated

Multiple System Setup

Up to 12 systems can operate simultaneously (band and RF environment dependent).

Important: Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered on.
Otherwise, scans from the other receivers will not detect that channel as occupied. For the BLX88, be sure to setup both transmitters before progressing to the
next receiver.

Turn on any other equipment that could cause interference during the performance so it will be detected during the group and channel scans in the following
steps.

Before you begin system set up, turn all receivers ON and all transmitters OFF.
For the first receiver:

1. Perform a group scan.

This finds the group with the most clear channels.

Note: For the BLX88, the group scan sets up both receivers at the same time.

2. Turn on the first transmitter and change the group and channel to match receiver.
3. Leave the transmitter on and continue with the additional systems.

Note: If the selected group does not contain enough open channels, manually select group "d" when setting up larger systems.

For each additional receiver:

1. Use manual setup to change the receiver to match the group setting of the first receiver. Recall that each time the
group setting is changed, a channel scan is automatically done.
2. Turn on the transmitter and change the group and channel to match the receiver.
3. Leave the transmitter on and continue to the next system.
4. Once all receivers are set up, perform an audio check on all microphones.
11/28
 Shure Incorporated

Manually Setting Receiver Group and Channel

The receiver group may need to be changed as part of a multiple system setup.

Group (letter)
1. Hold the group button on the receiver until the display begins to flash.
2. While the display is flashing, press the group button again to advance to the next group.

Note: Only the group setting will be displayed during the manual setup.

3. Once the desired group is reached, release the group button. The receiver automatically performs a channel scan.

Channel (number)
Always use a channel selected by the channel scan. However, if necessary, the channel can be set manually. Follow the same
steps above using the channel button instead of the group button.

Locking and Unlocking Controls

Lock system controls to prevent accidental setting changes or power off.

Transmitter (lock/unlock)
Turn the transmitter on. Hold the group button, then press the channel button for approximately 2 seconds. The LED indicator
rapidly flashes red when locked.

Receiver (lock/unlock)
Turn the receiver on. Simultaneously hold the group and channel button. The display flashes rapidly.

• When locked, the display flashes rapidly if any key is pressed.

• The BLX88 locks on both sides when locked from either side.

Tips to Improve Wireless System Performance

If you encounter interference or dropouts, try the following suggestions:

• Choose a different receiver channel

• Reposition the receiver so there is nothing obstructing a line of sight to the transmitter (including the audience)
• Avoid placing transmitter and receiver where metal or other dense materials may be present
• Move the receiver to the top of the equipment rack
• Remove nearby sources of wireless interference, such as cell phones, two-way radios, computers, media players, Wi-Fi
devices, and digital signal processors
• Charge or replace the transmitter battery
• Keep transmitters more than two meters (6 feet) apart
• Keep the transmitter and receiver more than 5 meters (16 feet) apart
• During sound check, mark trouble spots and ask presenters or performers to avoid those areas

12/28
 Shure Incorporated

Getting Good Sound

Correct Microphone Placement

• Hold the microphone within 12 inches from the sound source. For a warmer sound with increased bass presence, move
the microphone closer.
• Do not cover grille with hand.

Wearing the Headworn Microphone

• Position the headworn microphone 13 mm (1/2 in.) from the corner of your mouth.
• Position lavalier and headworn microphones so that clothing, jewelry, or other items do not bump or rub against the micro­
phone.

13/28
 Shure Incorporated

Adjusting Gain
Monitor the audio LED indicator on the receiver front panel when setting the transmitter gain.

• Green: normal levels

• Red: excessive sound levels (overload).

The red LED should only illuminate infrequently when you speak loudly or play your instrument loudly.

BLX1
Rotate the audio gain adjustment to increase (+) or decrease (−) the gain until desired level is reached.
For instruments, turn gain to minimum setting. For lavaliers, increase the gain as desired.

14/28
 Shure Incorporated

BLX2
The BLX2 features two gain level settings, default and attenuated (-10 dB). The default setting is used for most situations. If the
receiver audio LED flickers red often, set the microphone to attenuated. Use the channel button to change the gain setting.

1. Hold down the channel button for 5 seconds.

A dot appears on the lower right­hand corner of the LED display, which indicates −10 dB gain setting has been activat­
ed.

2. To change the gain back to default, hold the channel button again for 5 seconds, or until the dot disappears.

Batteries
Expected life for AA batteries is up to 14 hours (total battery life varies depending upon battery type and manufacturer).
When the LED indicator turns red, it signifies "low battery" with approximately 60 minutes of remaining battery life.

For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.

To remove batteries from the handheld transmitter, push them out through the opening in the microphone battery compartment.

15/28
 Shure Incorporated

WARNING: Battery packs shall not be exposed to excessive heat such as sunshine, fire, or the like.

Wearing the Bodypack Transmitter

Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.
For best results, the belt should be pressed against the base of the clip.

16/28
 Shure Incorporated

Power Off
Hold down the power button to power off the BLX2 or BLX4/88. To power off the BLX1, slide the power toggle switch to OFF.

Removing and Installing Identification Caps

The BLX2 is equipped with a black identification cap from the factory (dual vocal systems ship with additional gray cap).
To remove: Remove battery cover. Squeeze sides and pull off cap.
To install: Align the cap and click into place. Replace battery cover.

An Identification Cap Kit containing assorted colored caps is available as an optional accessory.

Troubleshooting
Issue Indicator Status Solution

Verify all sound system connections or adjust gain as

Receiver ready LED on needed (see Adjusting Gain)
Verify that the receiver is connected to mixer/amplifier

No sound or faint sound

Turn on transmitter
Make sure the batteries are installed correctly
Receiver ready LED off
Perform transmitter setup (see Single System Setup)
Insert fresh batteries

17/28
 Shure Incorporated

Issue Indicator Status Solution

Make sure DC adapter is securely plugged into electrical

Receiver LED screen off outlet.
Make sure receiver is powered on.

Transmitter indicator LED

Replace transmitter batteries (see Changing Batteries).
flashing red

Change receiver and transmitter to a different group and/

or channel.
Identify nearby sources of RF interference, and shut­
down or remove source.
Replace transmitter batteries.
Audio artifacts or dropouts Ready LED flickering or off Ensure that receiver and transmitter are positioned with­
in system parameters
System must be set up within recommended range and
receiver kept away from metallic surfaces.
Transmitter must be used in line of sight from receiver for
optimal sound

Audio LED on receiver indi­

Distortion Reduce transmitter gain (see Adjusting Gain).
cates overload (red)

Sound level variations when

Adjust transmitter gain as necessary (see Adjusting
switching to different N/A
Gain).
sources

Receiver/transmitter won't
LED/display flashing rapidly See Locking and Unlocking Controls.
turn off

Specifications
System
Working Range
91 m (300 ft) Line of Sight

Note: Actual range depends on RF signal absorption, reflection and interference.

Audio Frequency Response

50 to 15,000 Hz

Note: Dependent on microphone type

Total Harmonic Distortion

Ref. ±33 kHz deviation with 1 kHz tone

0.5%, typical
18/28
 Shure Incorporated

Dynamic Range
100 dB, A-weighted, typical

Operating Temperature
-18°C (0°F) to 57°C (135°F)

Note: Battery characteristics may limit this range.

Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) pro­
duces positive voltage on pin 2 (with respect to pin 3 of low­impedance output) and the tip of the high im­
pedance 1/4-inch output.

BLX1
Audio Input Level
max -16 dBV maximum

min (0 dB) +10 dBV maximum

Gain Adjustment Range

26 dB

Input Impedance
1 MΩ

RF Transmitter Output
10 mW, typical

varies by region

Dimensions
4.33 in. X 2.52 in. X 0.83 in. (110 mm X 64 mm X 21 mm) H x W x D

Weight
2.6 oz. (75 g), without batteries

Housing
Molded ABS

Power Requirements
2 LR6 AA batteries, 1.5 V, alkaline

Battery Life
up to 14 hours (alkaline)

Audio Input Level

0dB -20 dBV maximum

19/28
 Shure Incorporated

-10dB -10 dBV maximum

Gain Adjustment Range

10 dB

RF Transmitter Output
10 mW, typical

varies by region

Dimensions
8.82 in. X 2.09 in. (224 mm X 53 mm) L x Dia.

Weight
7.7 oz. (218 g) without batteries

Housing
Molded ABS

Power Requirements
2 LR6 AA batteries, 1.5 V, alkaline

Battery Life
up to 14 hours (alkaline)

BLX4 & BLX88

Output Impedance
XLR connector 200 Ω

6.35 mm (1/4") connector 50 Ω

Audio Output Level

Ref. ±33 kHz deviation with 1 kHz tone

XLR connector –27 dBV (into 100 kΩ load)

6.35 mm (1/4") connector –13 dBV (into 100 kΩ load)

RF Sensitivity
-105 dBm for 12 dB SINAD, typical

Image Rejection
>50 dB, typical

Dimensions
BLX4 1.57 in. X 7.40 in. X 4.06in. (40 mm X 188 mm X 103 mm) H x W x D

BLX88 1.50 in. X 12.13 in. X 3.98in. (38 mm X 308 mm X 101 mm) H x W x D

20/28
 Shure Incorporated

Weight
BLX4 8.5 oz. (241 g)

BLX88 15.1 oz. (429 g)

Housing
Molded ABS

Power Requirements
12–15 V DC @ 235 mA (BLX88, 320 mA), supplied by external power supply (tip positive)

Certifications
Meets essential requirements of the following European Directives:

• WEEE Directive 2002/96/EC, as amended by 2008/34/EC

• RoHS Directive 2011/65/EU

Note: Please follow your regional recycling scheme for batteries and electronic waste

This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: [email protected]

Certified under FCC Part 74.

• DD4BLX1A, DD4BLX1B, DD4BLX1C, DD4BLX1D; DD4BLX2A, DD4BLX2B, DD4BLX2C, DD4BLX2D, DD4BLX1W,

DD4BLX1S, DD4BLX2W, DD4BLX2S, DD4BLX1H11, DD4BLX2H11, DD4BLX1J11, DD4BLX2J11

Certified by ISED in Canada under RSS-102 and RSS-210.

• 616A-BLX1A, 616A-BLX1B, 616A-BLX1C, 616A-BLX1D; 616A-BLX2A, 616A-BLX2B, 616A-BLX2C, 616A-BLX2D, 616A-

BLX1H11, 616A-BLX2H11, 616A-BLX1J11, 616A-BLX2J11

Certified by ISED in Canada under RSS-123 and RSS-102.

• 616A-BLX1W, 616A-BLX1S, 616A-BLX2W, 616A-BLX2S

Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.

21/28
 Shure Incorporated

Important Product Information

LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for
possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to
operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de­
pends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the
appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

Information to the user

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa­
tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada Warning for Wireless

This device operates on a no­protection, no­interference basis. Should the user seek to obtain protection from other radio ser­
vices operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Econom­
ic Development Canada’s document Client Procedures Circular CPC­2­1­28, Voluntary Licensing of Licence­Exempt Low­Pow­
er Radio Apparatus in the TV Bands.
Ce dispositif fonctionne selon un régime de non‑brouillage et de non‑protection. Si l’utilisateur devait chercher à obtenir une
certaine protection contre d’autres services radio fonctionnant dans les mêmes bandes de télévision, une licence radio serait
requise. Pour en savoir plus, veuillez consulter la Circulaire des procédures concernant les clients CPC‑2‑1‑28, Délivrance de
licences sur une base volontaire pour les appareils radio de faible puissance exempts de licence et exploités dans les bandes
de télévision d’Innovation, Sciences et Développement économique Canada.
This device contains licence­exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop­
ment Canada’s licence­exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

22/28
 Shure Incorporated

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.

Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)

Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC perfor­
mance.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.

Australia Warning for Wireless

This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating
frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band.
WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.

Frequency Range and Transmitter Output Level

Band Range Output Power

H8 518 to 542 MHz 10 mW

H8E 518 to 542 MHz 10 mW

H9 512 to 542 MHz 10 mW

H10 542 to 572 MHz 10 mW

H10E 542 to 572 MHz 10 mW

H11 572 to 596 MHz 10 mW

H62 518 to 530 MHz 10 mW

J10 584 to 608 MHz 10 mW

J11 596 to 616 MHz 10 mW

K3E 606 to 630 MHz 10 mW

K12 614 to 638 MHz 10 mW

K14 614 to 638 MHz 10 mW

M15 662 to 686 MHz 10 mW

M17 662 to 686 MHz 10 mW

M18 694 to 703 MHz 10 mW

M19 694 to 703 10 mW

Q12 748 to 758 10 mW

Q24 748 to 758 MHz 10 mW

23/28
 Shure Incorporated

Band Range Output Power

Q25 742 to 766 MHz 10 mW

R12 794 to 806 MHz 10 mW

S8 823 to 832 MHz 10 mW

T11 863 to 865 MHz 10 mW

Note: Frequency bands might not be available for sale or authorized for use in all countries or regions.

NOTE: This Radio equipment is intended for use in musical professional entertainment and similar applications. This Radio apparatus may be capable of oper­
ating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power
levels for wireless microphone products.

Frequencies for European Countries

H8E 518-542 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, EST 518 - 542 MHz*

F, GB, GR, H, I, IS, L, LT 518 - 542 MHz*

NL, P, PL, S, SK, SLO 518 - 542 MHz*

DK, FIN, M, N *

HR, E, IRL, LV, RO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

K3E 606-630 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, EST 606 - 630 MHz*

24/28
 Shure Incorporated

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

F, GB, GR, H, I, IRL, L, LT 606 - 630 MHz*

NL, P, PL, S, SK, SLO 606 - 630 MHz*

DK, FIN, M, N *

HR, E, IRL, LV, RO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

K14 614-638 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, EST 614 - 638 MHz*

F, GB, GR, H, I, IS, L, LT 614 - 638 MHz*

NL, P, PL, S, SK, SLO 614 - 638 MHz*

DK, FIN, M, N *

HR, E, IRL, LV, RO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

25/28
 Shure Incorporated

K14 614-638 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, EST 614 - 638 MHz*

F, GB, GR, H, I, IS, L, LT 614 - 638 MHz*

NL, P, PL, S, SK, SLO 614 - 638 MHz*

DK, FIN, M, N *

HR, E, IRL, LV, RO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

Q25 614-638 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, EST 742 - 766 MHz*

F, GB, GR, H, I, IS, L, LT 742 - 766 MHz*

NL, P, PL, S, SK, SLO 742 - 766 MHz*

RO 742 - 743; 750 - 751; 758 - 759 MHz*

HR, E, IRL, LV, TR, DK, RIN, M, N *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

26/28
 Shure Incorporated

R12 796-806 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

N 796 - 806 MHz*

A, B, BG, CH, CY, CZ, D, DK, E, EST *

F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT *

LV, M, NL, P, PL, S, SK, SLO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

S8 823-832 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

BG, CH, D, DK, EST, F, FIN, IS, N, NL, S license free*

A, B, CY, CZ *

E, GB, GR, H, HR *

I, IRL, LV, L, LT, M, P, PL *

SK, SLO, RO, TR *

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

27/28
 Shure Incorporated

T11 863-865 MHz

Country Code Frequency Range

Code de Pays Gamme de frequences

Codice di paese Gamme di frequenza

Código de país Gama de frequencias

Länder-Kürzel Frequenzbereich

A, B, BG, CH, CY, CZ, D, DK, E, EST license free

F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT license free

LV, M, N, NL, P, PL, S, SK, SLO license free

TR 863 - 865 MHz*

* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.

28/28