Relays Extension Box REB-16
Installation Guide
~ N GND
CL D COM
COM D
R
E
L
ROTEM A
CONTROLLER Y
S
O
U
T
[Link] 19/06/2001 Rev:1.0 1
Relays Extension Box REB-16
Installation Guide
~ N GND
CL D COM
COM D
R
E
L
ROTEM A
CONTROLLER Y
S
O
U
T
[Link] 19/06/2001 Rev:1.0 2
Installation
The REB-16 must be installed by an authorized [Link]
must be disconnected to avoid electrical shock and damage.
To avoid exposing the REB-16 to harmful gases or high humidity,
it is recommended to install it in the service room.
Insttallation Categoty (Overvoltage Category) III
The power supply to the REB-16 should be protected by 5Amps circuit breaker.
1. Open the enclosure lid by unfastening the two screws to the left-hand side
in the front.
2. Place the required cables through the cable holders at the bottom of the
unit. Connect the wires according to the wiring diagrams:
3. Close the REB-16 enclosure lid carefully and tightly. Use RTV silicon or
equivalent sealant to seal the cable holders.
4. After installation is completed, operate the REB-16 for a few hours and re-
check for proper operation.
Specifications
Input Voltage Supply:
Single phase 110 VAC (USA & CANADA).
Single phase 240 VAC (Outside the US & CANADA).
0.315 Amp, 50 - 60 Hz.
Relays Outputs:
5 Amp. Normally Open Relays .
Alarm Output:
NO and NC Pilot Duty.
Operating Temperature Range:
-10°C to 50 °C ( 14 to 122 F° )
Enclosure :
Water and dust tight. (IP55)
Fuses:
Main Fuse: 0.315 Amp Slow.
Relays Fuse: 5 Amp. Slow.
ROTEM Computerized Controllers Ltd. 972-3-9206200 FAX: 972-3-9249834 ISRAEL
Web site [Link] Email- rotem@[Link]
[Link] 19/06/2001 Rev:1.0 3
Installation
The REB-16 must be installed by an authorized [Link]
must be disconnected to avoid electrical shock and damage.
To avoid exposing the REB-16 to harmful gases or high humidity,
it is recommended to install it in the service room.
Insttallation Categoty (Overvoltage Category) III
The power supply to the REB-16 should be protected by 5Amps circuit breaker.
5. Open the enclosure lid by unfastening the two screws to the left-hand side
in the front.
6. Place the required cables through the cable holders at the bottom of the
unit. Connect the wires according to the wiring diagrams:
7. Close the REB-16 enclosure lid carefully and tightly. Use RTV silicon or
equivalent sealant to seal the cable holders.
8. After installation is completed, operate the REB-16 for a few hours and re-
check for proper operation.
Specifications
Input Voltage Supply:
Single phase 110 VAC (USA & CANADA).
Single phase 240 VAC (Outside the US & CANADA).
0.315 Amp, 50 - 60 Hz.
Relays Outputs:
5 Amp. Normally Open Relays .
Alarm Output:
NO and NC Pilot Duty.
Operating Temperature Range:
-10°C to 50 °C ( 14 to 122 F° )
Enclosure :
Water and dust tight. (IP55)
Fuses:
Main Fuse: 0.315 Amp Slow.
Relays Fuse: 5 Amp. Slow.
ROTEM Computerized Controllers Ltd. 972-3-9206200 FAX: 972-3-9249834 ISRAEL
Web site [Link] Email- rotem@[Link]
[Link] 19/06/2001 Rev:1.0 4
