MasterProtect® 300
Pigmented, elastomeric and protective waterproof and anti-carbonation coating for
concrete and concrete structures
DESCRIPTION TYPICAL PROPERTIES
MasterProtect 300 is an elastomeric coating
based on acrylic co-polymers. Applied as a liquid Relative density: 1.3±0.1 at 25°C
it cures to form a durable, protective, waterproof
Tensile strength as >2.0MPa
membrane.
It is a single component emulsion containing inert per ASTM D412
pigments suitable for application by brush, spray Elongation as per >250%
or roller. ASTM D412
MasterProtect 300 prevents chloride ion ingress.
Reduction in chloride 97%
And exceeds all the requirements of a coating that
resists carbonation. ion ingress @ 28
days
PRIMARY USES Bond strength ASTM >2 MPa
MasterProtect 300 is designed for the protection D4541
of concrete structures against carbonation, Water absorption <1%
chloride water ingress. The product is also
suitable as a seamless and elastomeric Application 5°C to 35°C
waterproofing coating for timber, asbestos / fibre temperature
cement and zinc sheets, asphalt, built-up felt and Chemical resistance: Resistant to spillage of
tiles.
gasoline, diesel, sewage,
Areas of application are: weak acids and alkalis
• Concrete repairs.
• Marine environments Colours: Light Ivory, Grey and
• Bridge and highway structures White. Also available in
• Underpasses. other colours upon
• Multi storey car parks.
request
• Commercial buildings.
• Industrial buildings. Appearance after No colour change,
• Waterproofing a variety of substrates. 300hrs accelerated cracking, chalking or
• Flat roofs and sloping roofs weathering blistering observed
ADVANTAGES
APPLICATION PROCEDURE
• Elastomeric - capable of bridging cracks.
• Easily applied by roller, brush or airless spray. MasterProtect 300 can be applied by brush, roller
• Provides barrier against salts and atmospheric or airless spray equipment. For airless spray
gases. application dilute with 7% (1.4 litre/20 litre unit) by
volume of potable water. Use a tip size of 19-23
• Waterproof - protects concrete from
thou.
waterborne salts.
• U.V. stable - maintains its appearance.
SURFACE PREPAATION: CONCRETE
PACKAGING All concrete surfaces should be treated to achieve
a sound, clean surface free from laitance, oil,
MasterProtect 300 is supplied in 20 litre pails.
grease, mould release agent, residual curing
MasterProtect FL 100: 25kg bags
compound, dust or other contaminants that could
impair adhesion.
MasterProtect® 300
PRIMING APPLICATION:
All external surfaces should be primed with MasterProtect 300 is applied to the prepared
MasterKure 181 applied at approximate rate of surface in two coats, the first being allowed to dry,
5m²/litre, to eliminate excessive suction and before the second is applied.
promote adhesion. In temperatures >25°C,
application should be made a minimum of three In hot dry climates, application will be assisted by
hours before applying the MasterProtect 300 dampening brushes.
coating. In cold, humid conditions 24 hours is Where the roof is in poor condition, or where
required to ensure full solvent release. substantial movement is expected in the roof
For internal surfaces such as car park walls, structure, apply a sandwich system incorporating
columns and soffits PCI Primer Gisogrund may be reinforcing fabric.
used as an alternative primer. Please go to the In this application, the fabric is bedded into the wet
latest PCI Primer Gisogrund datasheet for film of the first coat of MasterProtect 300 using a
application rates and details. charged brush. Ensure that full contact is
Coating the concrete at an early stage prevents achieved and there is no air entrapped. Apply a
penetration of deleterious salts. MasterKure 181 second coat of MasterProtect 300 when the first
is recommended for metal decks. has dried, at right angles to the first.
FILLER/SCRAPE COAT WEATHER CONDITIONS
Surface depressions, blow holes, aggregate pop- MasterProtect 300 is not resistant to rain until the
outs etc., may be rectified with film has dried. This may take less than 30 minutes
MasterProtect FL 100. in hot dry climates and up to 24 hours in
temperate humid conditions. Generally the
The filler is tightly scraped onto the surface to be product should not be applied in rain or if rain is
overcoated, paying particular attention to ensure forecast. Similarly, MasterProtect 300 will freeze
blemishes are filled. Deeper aggregate pop-outs in its wet state so should not be applied to frozen
may require filling in two layers. substrates or when the temperature is below 5°C
or likely to fall during application.
The treated surface should be left to cure until the
deepest depressions are dry to the touch before COVERAGE
overcoating. Approximately 0.64Lt/m² to achieve a DFT of 400
microns (applied in a minimum of two coats).
Minimum coverage: 0.40 litre / m² to achieve a
APPLICATION: DFT of 250 microns.
Apply in one or more coats ensuring a continuous
even film. The finish may be textured if desired. STORAGE
Store under cover out of direct sunlight and protect
SURFACE PREPARATION: ROOF from extremes of temperature. If stored at high
WATERPROOFING temperatures or high humidity levels, the shelf life
Surfaces to be treated should be clean and dust of this product may be reduced. Shelf life is 6
free. All traces of oil, grease, mould release agent months.
and residual curing compounds should be
removed together with any other contaminant that Failure to comply with the recommended storage
could impair adhesion. Previous waterproofing conditions may result in premature deterioration of
treatments should be either completely removed the product or packaging. For specific storage
or put in order. Cracked, broken, slipped or advice consult BASF's Technical Services
missing tiles, sheets, slates or other forms of Department.
covering must be replaced or refixed. Cracks in
asphalt or built-up felt systems should be filled
with mastic and allowed to cure.
MasterProtect® 300
SAFETY PRECAUTIONS
As with all chemical products, care should be
taken during use and storage to avoid contact with
eyes, mouth, skin and foodstuffs. Treat splashes
to eyes and skin immediately. If accidentally
ingested, seek medical attention. Reseal
containers after use. Use in well ventilated areas
and avoid inhalation.
NOTE
Field service, where provided, does not constitute
supervisory responsibility. For additional
information contact your local BASF
representative.
BASF reserves the right to have the true cause of
any difficulty determined by accepted test
methods.
QUALITY AND CARE
All BASF Products are manufactured under a
management system independently certified to
conform to the requirements of the quality,
environmental and occupational health and safety
standards of ISO 9001 and BASF ESHQ
recommendations.
* Properties listed are based on laboratory controlled tests.
® = Registered trademark of the BASF-Group in many countries.
BASF_CC-UAE/Pr_300_06/12/v1/12_13-rev-04-2017
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by
NOTE BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not BASF, are responsible for carrying out procedures appropriate to a specific application.
Saudi BASF for Building Materials Co. Ltd.
P.O. Box 1884, Al Khobar, KSA
Tel: +966 13 8538600, Fax: +966 13 8328671
www.master-builders-solutions.sa
