Master Epoxy Finish
Material Safety Data Sheet
A two pack epoxy hi-build coating.
Research and Development Department
Master Paint Industries (Pvt) Ltd. 14 Egerton, Lahore.
Phone : 0 4 2 – 111 -333 – 465,
E-Mail :
[email protected]WWW.MASTERPAINTS.COM
MASTER’S Epoxy Finish
Data Sheet
PRODUCT INFORMATION
Description: Product Description
A two pack epoxy hi-build coating.
ALSO AVAILABLE IN SOLVENT FREE
Product Features
High build coating.
For use in industrial and corrosive marine service.
Areas subject to heavy wear and tear.
Portable water storage tanks.
Technical Information
VOC Content Less than 150G/LTR
Color White and Grey, other colors on request.
Finish Semi-Gloss
Generic Type Epoxy
Vol Solid 52 %
Mixing Ratio 4: 1
Spreading Rate 5.2 m2/ L. @100 µm dft.
Drying Time 2 -4 hrs. at 30 ºC.
Recoating Time 8 – 12 hrs.
Induction Time 15 mins.
Pot Life 8 hrs.
Curing Time Attains maximum hardness and chemical resistance 4 - 7 days.
Thinner / cleaner Epoxy
Weight / Litre 1.20 – 1.30 kg.
Flash Point 23 ᵒC, 73 ᵒF
2
Page
ISSUE 2018
Further coat Coat on coat
Packing size 4 litrs kit.
Surface Preparation
New plaster, Concrete brick work:
The concrete must be fully cured, e.g. 28 days for normal Portland
cement, and completely dry with humidity content in the surface below
4%. Primed/Sealed with 2-pack Epoxy Clear.
Steel:
Primed with 2-Pack Epoxy Primer.
Application
Brush or airless spray (preferable). Airless spray tip 13 thou, 2000 P.S.I. Not to be applied below 1
C. Mix individual components to uniform consistency ,then combine in recommended ratio,
allow to stand 15 min. before use. Thin as required For brush or spray application
with recommended thinner. Do not thin separately packed components. Use of thinner other than
that specified or recommended may adversely affect the product performance. Mix only that
quantity which is supposed to be consumed within the pot life of paint.
Conditions during application
The temperature of the substrate should be min. 3°C above the dew point of the air, temperature and
relative humidity not more than 70% measured in the vicinity of the substrate. Good ventilation is
necessary when the paint is used in confined spaces. Mix the paint to uniform consistency before
application.
3
Page
ISSUE 2018
Typical Painting System
On Concrete.
Mster Epoxy Clear/sealer 1 x 30 µm
Master Epoxy Coating 2 x 100 µm
On Steel
Master Epoxy Primer 1 x 50 µm
Master Epoxy Coating 2 x 100 µm
Storage
The product should be kept in well-ventilated place, protected from heat and direct sunlight.
The containers must be kept tightly closed.
Health and Safety
Ensure proper ventilation during application and drying of paint. Avoid inhalation of paint mist and
vapours and skin contact. Spillage of paint on skin should immediately be removed with suitable cleanser
soap and water. Eyes should be well flushed with water and immediate medical attention should be
sought.
============== OTHER INFORMATION ====================
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA BELIEVED TO BE RELIABLE.
IT IS TRUE & ACCURATE TO THE BEST OF OUR KNOWLEDGE, BUT IS NOT INTENDED TO
BE ALL INCLUSIVE. USERS SHOULD CONSIDER THIS INFORMATION AS A SUPPLEMENT
TO OTHER INFORMATION GATHERED BY THEM & MUST MAKE THEIR OWN
DETERMINATION OF SUITABILITY & COMPLETENESS TO ASSURE PROPER USE &
DISPOSAL.
================ END OF THE REPORT ================== 4
Page
