API Std 650 Storage Tank
GENERAL Special Documentation Package Requirements:
Measurement Units to be used in API Std 650: US
1. Manufacturer* Contract No.* TBD
Address*
Mfg. Serial No.* Year Built* Edition & Addendum to API 650*
2. Purchaser Contract
Address
Tank Designation
3. Owner Operator Locatio
4. Size Limitations* Tank Diameter ft Shell Height
Capacity: bbl Net Working* bbl Criteria:*
Maximum*
Liquid Max. S.G.: at deg
Blanketing Gas Vapor Pressure PSIA at Max. Operating Temp.
% Aromatic Suppl. Spec. H2S Service? Suppl. Spec.
Other Special Service Suppl.
DESIGN AND Purchaser to Review Design Prior to Ordering
6. Applicable API Standard 650
7. Max. Design Temp. deg Design Metal Temp.* deg Design Liquid Level
Design Pressure External Pressure Pressure Combination Factor
Maximum Fill Rate Maximum Emptying Rate
Floatation Flot. Suppl. Spec.* Applied Suppl. Load Spec.
8. Seismic Design? Appendix E Alt. Seismic Criteria Seismic Use Group
MBE Site Class Vertical Seismic Design? Vertical Ground Motion Accelerator Av:
Basis of Lat. Accel. (Select one):
Mapped Seismic Parameters Ss S1 So
Site-Specific MCE Design
Other (Non-ASCE)
Freeboard Required for SUG 1 Design Roof Tie Rods at Outer Ring?
9. Wind Velocity for non-U.S. sites, 50-yr wind speed (3-sec mp
Top Windgirder Style* Dimensions* Use Top WG as a Walkway?
Intermediate Wind Girders?* Intermediate Windgirder Dimension
Check Buckling in Corroded
10. Shell Design: 1-Ft Mthd?* Variable-Des-Pt Mthd?* Elastic Anal. Mthd?*
Plate Stacking Criteria* Centerline Stacked? Flush-Stacked?
Plate Widths (in.) (Shell course heights) and Thicknesses (in.)* Numbers Below Indicate Course Number
1. x 2. x 3. x 4.
5. x 6. x 7. x 8.
9. x 10. x 11. x 12.
13. x 14. x 15. x 16.
Joint Efficiency* % Shell-to-Bottom Weld Type* Shell-to-Bottom Weld Insp Mthd*
Approvals: Revisions (no./date) Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 1 of 10
API Std 650 Storage Tank
*If box is blank, Mfr. shall determine and submit as per Appendix L.
11. Open-Top and Fixed Roofs: (See Sheet 6 for Floating Roofs) Open Top?*
Fixed Roof Type* Roof Support Columns*
Cone Slope* : Dome or Umbrella IS Radius* in Weld
Seal Weld Underside of Lap Joints? ; Seal Weld Underside of Windgirder Joints?
Gas Tight? Joint Efficiency* % Roof Thickness* in
Minimum Roof Live Load psf Balanced Snow Load psf Unbalanced Snow Load psf
App. Suppl. Load Spec.* Column Lateral Load
Normal Venting Devices*: Qty Ty
Emergency Venting Devices*: pe
For Non-Frangible Roofs: Seal Weld Roof Plates to Top Angle IS ; Weld Rafters to Roof Plates
Roof-to-Shell Detail* Radial Projection of Horizontal Component*
12. Bottom: Thickness* in Style* Slope* : Weld Joint*
Provide Drip Ring? Alternate Spec.
SK/Ann. Ring? Annular Ring: Minimum Radial Width* in. Thickness*
13. Foundation Furnished By* Type*
Soil Allow. Bearing Press.* psi Per Spec. Anchor: Size Dia Qty
Design Loads: Base Shear: Wind* Seis.* Moment: Wind* Seis.*
Internal
Partial Vacuum* Wind* Siesmic*
Btm Forces: Flr Wt. Corr.* Prod. Wt.* Water Wt.* Int. Press.*
Partial Vacuum* Other Found. Loads* Min. Proj. of Found. Above Grade:
14. Responsibility for Heating Water, if Required?
Hydro-test Fill Height* Settlement Measure Req'd? Extended Duration of Hydro-test:
Predicted Settlement Profile is Attached
Responsibility for Setting Water Quality Suppl. Test Water Quality Spec.
Test Water Source & Disposal Tie-in Locations Hydro-test Appendix J Tank
Post-Press.-Test Activities Req'd of Mfr: Broom Clean Potable Water Rinse Dry Interior Other
List Other
15. Inspection by: Shop
Supplemental NDE Responsibility Supplemental NDE Spec.
Positve Material Identification? PMI
Max. Plate Thickness for Shearing
Must Welds not exceeding .25" be Multi-Pass? Must Welds greater than .25" be Multi-Pass?
Bottom* Floating Roof
Modify or Waive API Dimensional Tolerances (see 7.5) Specify:
Specify additional Tolerances, if any, and Circumferential and Vertical Measurement Locations:
Allowable Plumbness: Measure and Record at a Min. of Locations or Every ft around the
Tank , at the Following Heights: Specify Other:
Allowable Roundness:** Measure Radius and Record at a Min. of Locations or Every ft
around the Tank, at the Following Shell Heights: Specify Other:
** See Data Sheet Instructions for the Maximaum Allowable Additional Tolerance
Approvals: Revisions (no./date) Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 2 of 10
API Std 650 Storage Tank
16. Coatings:
Internal Linings Per
by: Spec.*
Under-Bottom Coating Per
by:
Per
17. Cathodic Protection
System? Per
Per
20. Tank Measurement Require Remote Capability
By: Required? Per Spec.*
21. Weight of Tank:
Full of Water* lbs Empty* lbs Shipping* lbs Brace/Lift Spec.
22. References*:
23 Remarks*:
Approvals: Revisions (no./date) Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 3 of 10
API Std 650 Storage Tank
Data Sheet
Data Sheet Status:
Page
4
of
10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
Table 1 MATERIALS OF CONSTRUCTION
Component Material* C.A. (in.) Component Material* C.A. (in.)
Shell Course to Manhole Necks
Shell Course to Nozzle Necks
Shell Course to Manhole Flanges
Shell Course to Nozzle Flanges
Shell Course to Manhole Covers
Roof Nozzle Covers
Bottom Manhole Gaskets
Annular Ring Nozzle Gaskets
Anchor Attachments Internal Piping
Reinforcing Pads Wetted Structurals+
Non-Wetted Struct.+
Table 2 BOLTS and ANCHORS
Flange Bolts Head Type* Material* Nut Material* Thread Series* C.A. (in.)
Flange Bolting++
Structural Bolting++
Misc. Bolting++
Anchor Bolts++
Remarks:
Approvals: Revisions Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 4 of 10
Data Sheet Status:
API Std 650 Storage Tank
Data Sheet Page
5 of 10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
Table 3 NOZZLE and MANHOLE SCHEDULE*
Bottom
Mark
Service
Diameter
(in)
Depth (in)
Thk (in)
Hor Rad(in)
"x" Dim
"y" Dim
Azimuth (deg)
Notes
Shell
Mark
Service
Nom.
Dia.
Wall
Thk
Flange Type
Flg Cl. or Thk
Hillside
Offset (in)
Elev.
(in.)
Azimuth (deg)
Proj.
(in)
Trim
Flush
Notes
Notes:
Approvals:
Revisions (no./date)
Title:
1
2
3
4
5
6
By Ckd Date
Draw. No.: Sheet 5 of 10
API Std 650 Storage Tank
Data Sheet
Data Sheet Status:
Page
6 of
10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
Table 3 NOZZLE and MANHOLE SCHEDULE* (cont'd)
Roof
Mark
Service
Nom.
Dia.
Wall
Thk
Flange Type
Flg Cl. or Thk
Vert or Radial
Horz Rad(in)
Slope Dim(in)
Azimuth (deg)
Proj.
(in)
Trim
Flush
Notes
Notes:
Approvals:
Revisions (no./date)
Title:
1
2
3
4
5
6
By Ckd Date
Draw. No.: Sheet 6 of 10
API Std 650 Storage Tank
Data Sheet
Data Sheet Status:
Page
7
of
10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
OTHER TANK APPURTENANCES
24. Platform: Top: Roof: Inter. Other Specify Other
Platform Material Walk. Surface Finish
Stairs: Type Specify Other Min. Width (in)
Min. Tread Max. Rise Tread Surface Tread Nose
IS Rail HR Height (in) HR Type Spec. Other Finish
Handrail: Type Spec. Other HR Height (in) Finish
Architectural/Structural Specs* National Safety Standards
Gauger's Platform Req'd? Qty. Req'd* Per Spec.*
Jacket Req'd?* Other Heaters/Coolers Req'd?*
21.
Suppl. Jacket, Heater or Cooler Specs.*
25. Mixer/Agitator: Quantity Size Per Spec.*
26. Insulation: Roof Req'd? Thick Mat'l Per Spec.
Shell Req'd? Thick Mat'l Per Spec.
Purchased By: Installation By:
27. Struct. Attachments: Lifting Lugs?* Description*
Shell Anchorage?* Type* Specify Other Scaffold Cable Support?
28. Other Items: Flush Drain? Type Specify Other Size
Flush Cleanout? Size Specify Other
Ground. Lugs? Qty Type Mat'l
Waive Application of Appendix P?
Miscellany #1 Miscellany #2
Miscellany #3 Miscellany #4
Miscellany #5 Miscellany #6
Table 4 OTHER TANK APPURTENANCES*
Mark
Qty
Service or Description
Size
Orientation
Elevation
Material
Remarks
Remarks:
Approvals:
Revisions (no./date)
Title:
1
2
3
4
5
6
By Ckd Date
Draw. No.: Sheet 7 of 10
API Std 650 Storage Tank
*If box is blank, Mfr. shall determine and submit as per Appendix L.
FLOATING ROOF
30. Floating Roof Selection:
Design Basis: Appendix C Appendix H
Type of Roof: (External or Internal): Sgl. Deck Pontoon* Double Deck*
(Internal Tubular Pontoon* Metallic Sandwich Panel* Other
Specify Other Suppl. Spec.:
31. Seals:
Primary Seal: Shoe Envelope Wiper/Comp Plate Other Specify Other
Shoe Mfg. Std. Other Specify Other
Electrically Isolate Mechanism from Wax Scrapers
Shoes? Carbon Steel Shoes to be
Secondary Shoe Envelope Wiper None Other Specify
32. Data for All Floating Roofs:
Overflow Openings in Shell Shell Extension Roof Drain Check Valves Required?
Acceptable?
Freeze Protection for Roof Drains Req'd? Suppl. Req.
Roof Drain to Ext. Noz.: Mfg. Std. Arm. Flex Pipe Swivel/Rig. Pipe Other
Foam Dam Supplemental Spec.
Nominal Deck Thick. (in) Bulkhead Top Edges to be Liquid-Tight Seal-weld Underside of
Electrical Bonding: Shunts Cables Supplemental Spec.
Qty of Non-Guide Pole Gauge Qty of Sample
Guide Pole for Gauging? Slots in Guide Pole? Datum Plates? Striking Plates?
GP Emmis.-Limit. Devices: Sliding Cover Pole Wiper Float Float Wiper Pole Cap
Qty of Roof Manholes*
Removable Leg Storage Minimum High Roof Clearance above Bottom
33. Additional Data for External Floating
Roofs:
Rolling Ladder Field Adjustable
Design Rainfall Intensity In/Hr Based on a Minute Duration Associated with the Storm
Design Accumulated 24-Hour Rainfall in Based on the Storm
Distortion and Stability Determinations Required? Suppl. Spec.
Landed Live Load* lbs
Remarks:
Approvals: Revisions (no./date) Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 8 of 10
API Std 650 Storage Tank
Data Sheet
Data Sheet Status:
Page
9
of
10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
34. Additional Data for Internal Flaoting
Two Position Legs? Cable
Internal Roof Drain Required? Corrosion Gauge Required? Modified Minimum Point Load?
Mfr To Leak Test* % of
Roofs:
SupportedRoof?
Fixed Ladder Supplemental Compartments w/Tank Hydro Product
Fixed Omit Distribution required? Specification in Assembly
WaterQuality:FilHeight
Fill:
Pads Type
Yardatcompletion
RoofInspection
Supporting of Roof
Hatches Required?
Uniform Live Loads?
Vent:*
of
Potable
in
Erected Position Unknown++
roof Not Req'd
at later date
Other Specify Other
List Attached
Other
Roof Erector's Floatation Test:
Floatation Test Media: Water
Floatation Test : Test Duration
Flotation Test Items provided by Purchaser Responsible Party for Inspecting Roof
(seeH.6.7):duringInitial
None
Purchaser
Table 5 FLOATING ROOF MATERIALS
Component
Mat'l/Thick.*
C.A./Coat.*
Component
Mat'l/Thick.*
C.A./Coat.*
Deck Plate
Datum Plate
Inner Rim Plate
Tubular Pontoon
Outer Rim Plate
Pontoon Bulkhead
Foam Dam
Submerged Pipe
Sandwich Panel Face Plate
Guide Pole
Sandwich Panel Core
Secondary Seal
Gauge Well
Secondary Seal Fabric
Drain Sumps
Wiper Tip
Opening Sleeves
Wax Scraper
Floating Suction Lines
Weather Seal
Primary Fabric Seal
Envelope Fabric
Foam Log Core
Shoe Mechanisms
Landing Legs
Primary Seal Shoe
Landing Leg Bottom Pads
Removable Covers
Manhole Necks
Rolling Ladder
Vents
Inlet Diffusers
Approvals:
Revisions (no./date)
Title:
1
2
3
4
5
6
By Ckd Date
Draw. No.: Sheet 9 of 10
*If box is blank, Mfr. shall determine and submit as per Appendix L.
Tank Plan and Sketches:
Notes:
Approvals: Revisions (no./date) Title:
1 2 3 4 5 6 By Ckd Date
Draw. No.: Sheet 10 of 10
