UHT-75 - UHT.79 ASME [Link][T.

2O27

Tabl.e UHT-56
Postweld Heat Treatment Requirements for Materials in Tabl.e UHT-23

Spec. No. Grade or Type

P-No,/
Gr. No.
Nominal Thickness
Requiring PWHT,
in. (mm) Notes PWHT Temp., "F ["C)
-,#ÏHk;
f25 mm) hr
Plate Steels
sA-353 9Ni L1A/7 Over 2 (50) .., 1,025-1,085 (ss0-s85) I 2
sA-5 17 Grade A L7B/7 Over 0.58 (15J i1) 1,000-1,100ts4O-ses) 1 lo
sA-5 17 Grade B 718/4 Over 0.58 (15) t1l 1,000 1,100 [s40-s95J L ln
sA-517 Grade E 778/2 Over 0.58 (15) (1) 1,000 '1,100 (s40-s9sJ 1 ln
sA-5 17 Grade F 't-78/3 over 0.58 (15) (1) 1,000 -1,1 00 (s40-s9sJ 1 ln
sA-5 17 Grade J 7LB/6 Over 0.58 (15) (l) 1,000-1,roo(s4o-ses) 1, l*
sA-5 17 Grade P 1-1-B/8 over 0.58 (15) (11 1,000-1,1 00 (s40-s9sl L ln
sA-533 al
Types B, D, Cl. 3 LTA/4 Over 0.58 (15) 1,000- 1,05 0 (s4o-s 6sJ t2 f,
sA-543 Types B, C, Cl. 1 774/s (2) 1,000-1,05 0 (s40-s 6s) 1
sA-543 Types B, C, Cl. 2 1-18/70 (z) 1,000-1,05 0 (s40 s6s) 1
sA-543 Types B, C, Cl. 3 1-14/s (2) 1,000-1,05 0 (s4o-s 6sJ L
sA-553 Types l, Il, lll 1,1,4/1, over 2 (50) 1,025- 1,085 (s s o-s 8sJ 2
sA-645 Grade A 774/2 Over 2 (501 1,025-1,085 (ss 0-s Bs) 2
sA-724 Grade A, B 1/4 None NA NA NA
sA-724 Grade C 7/4 over 1% (38) ... 1,050-1,150 (s6s-620J 7 Ir
Castings
sA-487 Class 48 71-A/3 Over 0,58 (15) ... 1,000-1,050 [s40-s6s) \ '/o
sA-487 Class 4E 1-LA/3 Over 0.58 (15) ... 1,000-1,050 [s40-s6s) r lo
sA-487 Class CA 6NM 6/4 Over 0,58 [15) ... 1,050-1,150 (s6s-620) 1 '/o

Pipes and Tubes

SA-333 Grade B L1A/1 Over 2 (50) ... 1,025-1,085 (sso-s8s] 1
SA-334 Grade 8 1,74/r over 2 [50) .,, 1,025-1,085 (ss0-s8s) 1

Forgings
sA-508 Grade 4N Cl. 1 1,1,4/s (z) 1,000-1,050 (540-565J 1 1
SA-5OB Grade 4N Cl. 2 r7B /10 12) 1,000-1,050 (540 565J 1 7
sA-522 Type I 1,74/7 over 2 (50) ,,, 1,025-1,085[550-585) 1 2
sA-592 Crade A rlB/1 Over 0.58 (15J (11 1,000-1,100 (s40 s9s) 1 7n
sA-59 2 Grade E LIB/z over 0.58 (15) (1) 1,000-1,100 (s40-59s) 7 ln
sA-592 Grade F IIB/3 Over 0.58 f15l f1l 1,000-1,100 f540-5951 7 1/"

GENERAL NOTE: NA = not applicable.

NOTES:
(1) See UHT-82[gJ.
(2) PWHT is neither required nor prohibited, Consideration should be given to the possibility of temper embrittlement. The cooling rate
from PWHT, when used, shall not be slower than that obtained by cooling in still air.

FABRICATION UHT-79 FORMING PRESSURE PARTS

UHT-75 GENERAL The selected thickness of material shall be such that lhe
The rules in the following paragraphs apply specifically forming processes will not reduce the thicl<nessi of lhe
to the fabrication of pressure vessels and vessel parts that
material at any point below the minimum value requir:ed
are constructed of heat-treated steels covered by this Part by the rules.
and shall be used in conjunction with the general require- [aJ Pieces that are formed after heat treatment at a
ments for Fabrication in Subsection A, and, when applica- temperature lower than the final tempering shall be heat
ble, with the specific requirements for Fabrication in treated in accordance with Table UHT-56 when the ex-
Subsection B, Part UW. treme fiber elongation from forming exceeds lj%o as deter-
mined by the equations in Table UG-79-1.
[b.) Pieces that are formed at temperatures equal to or
higher than the original tempering shall be reheat treated
in accordance with the applicable material specifïcation,
either before or after welding into the vessel.

234