Dry Bath
User Manual
HB120-S LED Digital Dry Bath
Please read the User Manual carefully before use, and follow all
operating and safety instructions!
Technical specifications and outline are subject to change without prior
notice.
[Link]
Contents
Preface ................................................................................. 1
Service ................................................................................. 1
Warranty .............................................................................. 1
1. Safety Instructions ....................................................... 3
2. Proper Use ................................................................... 4
3. Inspection .................................................................... 4
3.1 Receiving Inspection .............................................. 4
3.2 Listing of Items....................................................... 4
4. Control ......................................................................... 5
4.1 Control elements ................................................... 5
4.2 Display ................................................................... 6
5. Trial Run...................................................................... 6
6. Function: Heating ........................................................ 7
7. Function: timing .......................................................... 7
8. Faults ........................................................................... 8
9. Maintenance and Cleaning .......................................... 8
10. Associated Standards and Regulations ........................ 9
11. Specifications ............................................................ 10
12. Ordering Information ................................................ 10
Preface Please provide the customer care representative with the
following information：
Welcome to the “ Dry Bath User Manual ” . Users should ・ Serialnumber（on the rear panel）
read this Manual carefully, follow the instructions and ・Certification
procedures, and be aware of all the cautions when using this ・ Description problem
of (i.e., hardware or software)
instrument. ・ Methods and procedures adopted to resolve the problems
・ Your contact information
Service
When help needed, you can always contact the Service Warranty
Department of manufacturer for technical support in the Changes or modifications not expressly approved by the
following ways: party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
DLAB Scientific Instrument Inc.
comply with the limits for a Class A digital device, pursuant
2311 E. Locust Court, Ontario, CA 91761 United States.
Office: +1-747-230-5179 to Part 15 of the FCC Rules. These limits are designed to
Fax: +1-909-230-5275 provide reasonable protection against harmful interference
Sales contact: info@[Link] when the equipment is operated in a commercial
Service contact: service@[Link]
environment. This equipment generates, uses, and can
[Link]
radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of
1
this equipment in a residential area is likely to cause
harmful interference in which case the user will be required
to correct the interference at his own expense.
This instrument is warranted to be free from defects in
materials and workmanship under normal use and service,
for a period of 24 months from the date of invoice. The
warranty is extended only to the original purchaser. It shall
not apply to any product or parts which have been damaged
on account of improper installation, improper connections,
misuse, accident or abnormal conditions of operation.
For claims under the warranty please contact your local
supplier. You may also send the instrument directly to
manufacturer, enclosing the invoice copy and by giving
reasons for the claim
2
substances or under water.
1. Safety Instructions • Temperature must always be set at least 50℃ lower than
Warning! the fire point of the media used.
• Read the operating instructions carefully • Be aware of hazards due to:
before use. - Flammable materials or media with a low boiling
• Ensure that only trained staff works with the temperature
instrument. - Overfilling of media
Risk of burn! - Unsafe container
• Caution when touch the housing parts and • Process pathogenic materials only in closed vessels.
the dry bath which can reach temperature of • Check the instrument and accessories prior to each use.
120°C. • Do not use damaged components. Safe operation is only
• Pay attention to the residual heat after guaranteed with the accessories provided by the
switching off. manufacturer. Accessories must be securely attached to
Protective ground contact！ the device and can’t come off by themselves. Always
• Make sure that socket must be grounded disconnect the plug before fitting accessories.
(protective ground contact) before use. • The instrument can only be disconnected from the main
• When working wear personal safety guards to avoid the power supply by pulling out the main or the connector plug.
risk from: • The voltage stated on the label must correspond to the
- Splashing and evaporation of liquids main power supply.
- Release of toxic or combustible gases • Ensure that the main power supply cable does not touch
• Set up the instrument in a spacious are on a stable, clean, the dry bath. Do not cover the device.
non-slip, dry and fireproof surface. Do not operate the • The instrument may only be opened by experts.
instrument in explosive atmospheres, with hazardous
3
2. Proper Use 3. Inspection
The instrument is designed for heating liquids in schools, 3.1 Receiving Inspection
laboratories or factories.
Unpack the equipment carefully and check for any damages
• Observe the minimum distances between the devices,
which may have arisen during transport. Please contact
between the device and the wall and above the assembly
manufacturer/supplier for technical support.
(min. 100 mm)
Note:
If there is any apparent damage to the system,
>100mm please do not plug it into the power line.
3.2 Listing of Items
The package includes the following items:
Items Qty
Main unit 1
Power cable 1
User Manual 1
Figure 1
Table 1
This device is not suitable for using in residential areas or
other constraints mentioned in Chapter 1.
4
4. Control Items Descriptions
4.1 Control elements Temperature Press the button, can set the target
switch button temperature
Time switch
Press the button, can set the target time
LED display button
LED light LED displays the real working state
LED Display
and all settings.
Power switch
The LED light shows green when the
LED Light
Parameter
parameter is set
Temperature switch setting knob Rotate the knob to set the target
button Parameter setting
Time switch button
parameters, press the knob to turn on
knob the settings.
Power Switch Switch ON or OFF the instrument.
Figure 2 Dry bath
Table 2
5
4.2 Display flashing, and then rotate the parameter
setting knob to set the target time, press
the parameter setting knob to turn on the
setting. The LED time light will turn
green, then start countdown.
Table 3
Temperature display area Time display area
Figure 6 Digital hotplate model 5. Trial Run
• Make sure the required operating voltage and power
Characters Descriptions
supply voltage match.
Temperature Press the temperature switch button, the
• Ensure the socket must be properly grounded.
display area characters in temperature display area will
• Add the medium into the vessel
be flashing, and then rotate the parameter
• Place vessel on the work plate.
setting knob to set the target temperature,
• Plug in the power cable，ensure the power is on and begin
press the parameter setting knob to turn on
initializing.
the setting.
• Set the target temperature and begin.
When the heating function is switched
• Set the time, if not, the machine will work continuously
ON, the LED temperature light will turn
• Observe the LED display
green, and the temperature display area
• Stop the heating and stirring functions.
displays the temperature real value until
If these operations above are normal, the device is ready to
real temperature reaches the set point.
operate. If not, the device may be damaged during
Time display Press the time switch button, the
transportation, please contact manufacturer/supplier for
area characters in time display area will be
technical support
6
6. Function: Heating 7. Function: Timing
The device can work in accordance with the timing mode or
The device is controlled by digital temperature control
continuous operation mode.
technology, and it has a over temperature protection, the
Timing Mode: Press the time switch button, the characters
safety temperature is 140℃
in time display area will be flashing, and then rotate the
Press the temperature switch button, the characters in
parameter setting knob to set the target time, press the
temperature display area will be flashing, and then rotate
parameter setting knob to turn on the setting.
the parameter setting knob to set the target temperature,
During operation, motion can be stopped at any time by
press the parameter setting knob to turn on the setting.
pressing the speed/timer control knob. If the knob is
Note:
pressed again, motion will start again and the timer will
• Set the temperature via rotating the parameter setting
restart countdown. When the timer reaches zero, the unit
knob slowly to the target value.
• When the heating function is switched on, the LED
will be automatically halted.
displays the temperature value on the left-hand side. Continuous Mode: Press the time switch button, the
• The heating function is switched on or off by pushing
characters in time display area will be flashing, make sure
the setting time is zero, press the parameter setting knob to
heating knob.
turn on the continuous operation mode.
The instrument automatically displays the last running
speed and temperature parameters once turned on.
Generally, the LED screen cannot display the actual
temperature of sample in the vessel or dry bath surface,
temperature differences as following:
- Dry bath center and outer edge.
- The sample in the vessel and dry bath surface.
7
8. Faults / Isopropyl alcohol
Foodstuffs Water containing tenside
• Instruments can’t be power ON
Fuels Water containing tenside
- Check whether the power line is unplugged
• Before using other method for cleaning or
- Check whether the fuse is broken or loose
decontamination, the user must ascertain with the
• Fault in power on self test
manufacturer that this method will not harm the
- Switch OFF the unit, then switch ON and reset
instrument. Wear the proper protective gloves during
the instruments to factory default setting.
cleaning of the instrument.
If these faults are not resolved, please contact
Note:
manufacturer/supplier.
• Electronic device can not clean with
cleanser.
9. Maintenance and Cleaning • If you require maintenance service, must be
cleaned the instrument in advance to avoid
• Proper maintenance can keep instruments working
pollution of hazardous substances, and to
properly and lengthen its lifetime.
send back into original packing.
• Do not spray cleanser into the instrument when
• If the instrument will not use for a long time,
cleaning.
please switch off and place in a dry, clean,
• Unplug the power line when cleaning.
room temperature and stable location.
• Only use recommended cleansers:
Dyes Isopropyl alcohol
Construction materials Water containing tenside
/ Isopropyl alcohol
Cosmetics Water containing tenside
8
10. Associated Standards and interference when the equipment is operated in a
commercial environment. This equipment generates, uses,
Regulations and can radiate radio frequency energy and, if not installed
Construction in accordance with the following safety and used in accordance with the instruction manual, may
standards: cause harmful interference to radio communications.
EN 61010-1 Operation of this equipment in a residential area is likely to
UL 3101-1 cause harmful interference in which case the user will be
CAN/CSA C22.2(1010-1) required to correct the interference at his own expense.
EN 61010-2-10
Construction in accordance with the following EMC
standards:
EN 61326-1
Associated EU guidelines:
EMC-guidelines: 89/336/EWG
Instrument guidelines: 73/023/EWG
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
9
11. Specifications Protection class according to
IP 21
DIN EN 60529
Items Specifications
Voltage [VAC] 100~120/200~240 Table 4
Frequency [Hz] 50/60
Power [W] 160 12. Ordering Information
Dimension of blocks[mm] 150×95 Cat No. Descriptions
Room temp. +5°- HB120-S, LED digital dry bath, USA
Heating temperature range 521111017777
120 °C plug, 100-120V, 50Hz/60Hz
Temperature display LED HB120-S, LED digital dry bath,, Cn
Control accuracy ±0.5°C 521111127777
plug, 200-240V, 50Hz/60Hz
Safety temperature 140 °C HB120-S, LED digital dry bath,, Euro
Timer yes 521111227777
plug, 200-240V, 50Hz/60Hz
Time setting range 1 -99h59min HB120-S, LED digital dry bath,, UK
Continuous/ timed 521111327777
Operation type plug, 200-240V, 50Hz/60Hz
operation Table 5
Dimensions[W×D×H mm] 175×290×85
1.6（without heating
Weight[kg]
block）
Permissible ambient
5 - 40 °C
temperature
Permissible relative humidity 80%
10
DLAB Scientific Instrument Inc.
2311 E. Locust Court, Ontario, CA 91761 United States.
Office: +1-747-230-5179
Fax: +1-909-230-5275
Sales contact: info@[Link]
Service contact: service@[Link]
[Link]
