Safety Cautions Outer Body Parts

Number Pad Lighted

This section contains important information to ensure the user’s Number Pad Unlighted
safety and prevent potential damage to property. Please, read
Warning this section carefully and use the product accordingly.
Number Pad

SHS-H635
• The user shall not install or repair the by engagement of the lock on an
product without authorization. improperly closed door.
• Do not install the product in the place • Please do not hang on the product or
where the gap between the door and the pull it. Enter Number
frame is 5mm or more.
CARD
Button
USER MANUAL • Make sure that no unauthorized person
• Be sure to correctly match the poles
(+/-) when installing the batteries. Install CARD
CARD
Card Reader
has the access to the password. LED Indicator
the batteries with the correct poles (+/-).
• Do not operate the product with wet • Long-term exposure to direct sunlight
hands, and keep liquids such as water may cause a crack on its touch pad.
or drinks away from the product, or
Avoid exposure to direct sunlight during
the product may malfunction or be
damaged. installation. Outer Body Handle

• Do not use the excessive force or sharp • During battery replacement, use a new
one instead of the existing battery. Emergency
objects to push the lockbuttons, as this Keyhole
can damage the product. • Do not use water, benzene or alcohol
when cleaning the product, as these External Power
Convenient Opening • Make sure that the door is completely fluids can cause product malfunction. Port
- User friendly access with
cards and password
closed when going outside. The
manufacturer does not assume the • Replace the batteries within 1 week Inner Body Parts
Graphic Interface responsibility for any harm caused after the battery replacement alarm
- Shows the operation status sounds.
of the doorlock
Double Authorization Product Components
- Requires card & password
combination to open The product components used may vary depending on the installation Battery Cover
CARD

Double Locking environment.

- Prevents opening from outside
(Do not disturb) Sound Control
Switch
Built-in Fire Detection Auto/Manual
- Generates alarm in case of a fire Locking Switch
Security Function Registration CLOSE Button
- Prevents intrusion from the outside Button
Manual Open-
Mortise Strike Inner body and close
CARD (SHS-AML320) Handle Lever
Or
CARD

Mortise
Mortise Strike Strike
Outer Body (SHS-AML220) box Inner Body

Key Tag Handle Shaft • Inner Fastening Bolts

User Manual Handle Shaft Spring • Strike Fastening Bolts
‘AA’ Batteries (LR6) • Support Panel and Inner Deadbolt
Emergency Key (5EA) Body Fastening Bolts
• Support Panel and Outer Latch bolt
Body Fastening Bolts Open-door sensor
www.samsungsds-nss.com/en GC68-02068B ED:01

2 SHS-AML320 SHS-AML220 3

Opening the Door from Outside with a Password Opening the Door from the Inside Initialization (Password, Card, Key Tag)
When purchased, the product is set to Multi-leveled Security Code Entry Mode Pulling down the Door Lock Handle Rotating the Manual Open/Close All registered data (password, card, key tag) are deleted. After initialization, the
initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Lever to the Right or Left password is set to ‘12345’, and the registered card, key tag data are erased.
Common Mode setting. Please register a new password after initialization.
Too~~~t
1. Multi-leveled Security Code Entry Mode 1. Pressing the [Register] Button 2. Entering the Numbers for
(from the inside) Initialization (from the outside)

Success: Too~~~t
Fail: Toot Toot→ Toot, toot
CARD
→ Toot, toot, toot, toot
Rotate the door lock handle of the inner Rotate the manual Open/Close lever
Pressing the [Enter When two arbitrary When the numbers on the body downward. to the right or left to lock the door or
Number] Button will buttons are lighted, number pad are lighted, release the locking.
light up the number press the buttons in enter the password and Press and hold the [Register] button When the number pad is lighted, enter
pad order. for 5 seconds. ‘4560852580’ and then press the [] button.
press the [] button.
- Success: Too~~~t
- Fail: Toot
2. Common Mode Closing the Door from the Outside
Pressing the [Enter Number ] Button
Success: Too~~~t
Password Change
Fail: Toot
CARD

The password can be 5~12 digits number. Only one password can be registered.
Pressing the [Enter Number] Enter the password when the When you come out opening the door from the 1. Pressing the [Register] Button 2. Entering the Current Password
Button will light up the number pad is lighted, and press inside in the Manual Locking mode, press the [Enter
number pad the [] button. Number] Button on the outer body. (from the inside) (from the outside)
CARD

● Password must be entered after the light is on, and if does not, touch Toot Too~~~t,
[Number Pad] and re-enter. toot, toot
Note ● To cancel, press [ ] button and re-enter.
● If the password is wrong 5 times, “Toot~, Toot~, Toot~” warning alarm will
sound 20 times and the system will shut-down for about 3 minutes. When
Closing the Door from the Inside
malfunction happens, “Toot” will sound every 10 seconds, and stop mode will Open the battery cover of the inner Enter the current password (‘12345’ after
be turned off automatically after 3 minutes with multiple ‘beeps’. Closing the Door from the Inside In the Manual Locking Mode body and briefly press the [Register] initialization) when the number pad is lighted,
button. and press the [] button.

3. Entering a New Password 4. Reentering a New Password

Opening the Door from Outside with a Card or (from the outside) (from the outside)
Key Tag
Too, Toot Too~~~t
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.

Placing the Card or Key Tag on the Card Reader

SHS-AML320 SHS-AML220
Enter the new password (5 to 12 digits) Enter the new password again to check if the
and press the [] button. new password is accurately configured, and
The door is automatically locked The door is locked when the [Close] - To prevent burglary, it is recommended then press the [] button.
Success: Too~~~t 2 seconds after the door is closed. button is pressed, or the manual Open/
CARD to use a password of 6 digits or longer.
Fail: Toot Close lever is rotated. (Only numbers between 0 and 9 can
be used.)
Place the card or key tag on the card reader.
The door will be opened after 1 second.
4 5 6
5. Checking New Password Operation (from the outside) Deleting the Card or Key Tag ●T  he setup of double authorization mode only works when the door is open.
● When purchased, the product is not set to double authorization mode initially.
To make sure the password has been Note ●T  o setup the double authorization mode, more than 1 card must be registered.
Too~~~t ●R
 egistered cards cannot be individually deleted. All card information is ●D  ouble authorization mode will automatically be turned off when all cards are
properly registered, check the new
deleted when the card delete function is selected. Previously registered cards deleted.
password and close the door. Warning cannot be used to open the locked door after they are deleted.

●M  anage your password with care so that unauthorized people will not have
1. Pressing the [Register] 2. Entering the Password Setting the Security Function
Button (from the inside) (from the outside)
access to it. Regularly changing your password can reduce the risk of it
being leaked. Setting the Security Function
Warning Too~~~t
● A registered password cannot be deleted. Change the password to a new Toot→ Toot, toot 1. When the door is closed [ ]
one or initialize it to delete all registered data (password, card and key tag)
of the outside body’s number
and then reregister them.
Too~~t pad will light up.
2. Press and hold the [ ] button on the
Open the battery cover of the Enter the password when the number outer body for 3 seconds while the
inner body and press and hold the pad is lighted, and press the [] button. door is locked.
Card and Key Tag Registration [Register] button for 3 seconds. - Success: Too~~~t
- Fail: Toot Releasing the Security Function
Up to 20 cards, including the key tag, can be registered.
(Only ISO14443 A Type is available.) ●R  egister a new card after deleting the card data. Apply the registered card or key tag to
● To open the locked door from outside after deleting card data, use the Or the card reader, or enter the password
1. Pressing the [Register] 2. E
 ntering the Password Note registered password. CARD
and then press the [] button.
Button (from the inside) (from the outside) ● Deleting the card or key tag is available while the door is open.

Too~~~t, toot, toot

Toot
Multi-leveled Security Code Entry Mode Setting ●T
 he security function is automatically released when the locked door is
opened from outside by entering the registered password or applying the
Note card or key tag to the card reader.
You can set the security mode suitable for your use when you open the
door using a password.
Open the battery cover of the Enter the password when the
inner body and briefly press the number pad is lighted, and Setting the Double Locking
[Register] button. press the [] button. Too~~~t
Toot
[7] Button : Multi-leveled Security The double locking function prevents opening of a locked door from outside.
Code Entry Mode
3. Placing the Card or Key Tag 4. C
 onfirming Card or Key Tag [9] Button : Common Mode Setting Double Locking Releasing Double Locking
on the Card Reader (from the Registration (from the outside)
outside) Briefly press the [Register] Press the [] button after pressing the
button on the inner body. [7] or [9] button, and the security mode Too~~~t
will be set.
Too~~~t
CARD CARD
Press the [Close] button for 2 The double locking function is released
Double Authorization Mode Setting seconds or longer from the inside when the inner body handle is rotated
Place the card or key tag to be Place the registered card or key while the door is locked. downward, or the manual Open/Close
registered on the card reader of the tag to the card reader on the Double authorization mode requires both card and password to open the lever is rotated to the right or left.
outer body. You will know the card or outer body.
door, ensuring more security.
key tag has been registered when Activating Double Locking
“Too~~~t” sounds.
Too~~~t Inside : T
 he double locking sound is generated
Toot when the [Close] button is pressed.
Too~~t
● To register multiple cards or key tags, lightly place another card or key tag [4] Button : Double authorization Outside : T he double locking sound is
to the card reader within 20 seconds after registering the previous card or mode on Or Too~~t generated, the double locking display
Warning key tag. [6] Button : Double authorization CARD LED is lighted, and the door cannot
mode off
be opened When the [Enter Number]
Briefly press the [Register] Press the [] button after pressing the Button is pressed, or a card is applied.
button on the inner body. [4] or [6] button, and the authorization
mode will be set.
7 8 9

●P
 lease be cautious when using this function, since the door can only be Replacing the Batteries Intrusion Detection Function
opened from the outside using the emergency key when this function
Warning is set. Please be particularly careful of children accidentally setting this
function from the inside. Battery Replacement Alarm Generation This function generates the alarm sound when an attempt is made to
forcefully open the door from the inside or the outside.
If the melody of “Blues for Elise” sounds when opening the door with the
(This is a basic function of the lock, and cannot be separately set or released.)
password or a card (key tag), it is time to replace the batteries.
Automatic/Manual Locking Setting (The low battery indicator is lighted when the melody sounds.)

The Automatic Locking mode allows for automatic locking of the door Replacing the Battery Built-in Fire Detection Function
when it is closed.
Replace all batteries within a week from the first alarm sound. This function generates the alarm sound when fire is detected so that the
residence can quickly respond. The built-in fire detection function is a basic
Set the [Automatic/Manual Locking] toggle switch of function of the lock, and cannot be released by the user.
● If the poles of the batteries are not placed properly, the lock will not
the Inner Body to the ‘A’/‘M’ position.
operate normally. When fire occurs, the temperature sensor detects it and flashes the [Close] button
Warning ● Liquid leaks from batteries can damage the product. Check the batteries while generating the alarm sound.
- Automatic: The door is automatically locked 2 seconds after being closed. regularly (every 6 months). The door is automatically opened after the alarm sound has stopped.
- Manual: T
 he door does not lock automatically, and [CLOSE] button must be ●A  fter the battery replacement alarm has sounded, password/card (The lock resumes normal operation if the inside temperature returns to a normal
pressed from the inside, press the [Enter Number] Button to close information cannot be registered, changed, deleted, initialized or level.)
the door. configured until the batteries are replaced. The built-in fire detection function is activated when the temperature rises around
● The unit will stop operating suddenly if the batteries are not replaced. 60℃, which may differ depending on the installation environment.

Sound Setting and Releasing

The sound that is generated when the number buttons are pressed, when the Product Specifications
door is locked or when the locked door is unlocked, can be set according to
the user’s preference. The product is set to generate all sounds at the factory.
Using the Emergency Battery
Item Specifications
If the batteries are not replaced after their replacement time comes, they will
WTXTY be completely discharged and the lock will not operate. Voltage 8EA of 1.5V AA Alkaline Batteries(LR6) (6V)
Emergency
Purchase an emergency battery (9V) at the nearest store. Power 9V Battery (6LF22) (Separately sold)
Open the battery cover on the Put the [Sound Control] switch on Source
- As the alkaline batteries offer longer life, they are recommended over the
inner body. one of [0], [1], or [2], and close the manganese batteries or rechargeable ones.
battery cover. Operation Electronic Control Method (Password entry or card or
Method key tag reading)
- [ 0 ] Button: All sounds except the alarm sound are deactivated.
Weight 2.6Kg (including both inner and outer bodies)
- [1] and [2] Buttons: All sounds are activated and the sounds get bigger as the step
become higher. Outer Body
(including 81.2 mm(W) x 306.0 mm(H) x 65.7 mm(D)
CARD CARD

Product the handle)

Alarm Sound (Prank Prevention Function) Or Dimensions Inner Body
(including 79.0 mm(W) × 290.0 mm(H) × 80.3 mm(D)
This function generates an alarm sound and deactivates lock operation the handle)
when it is improperly handled from the outside.
This alarm will sound if an attempt is made to open the door with an invalid card, or if ●T
 he contents of this user guide are subject to change without prior notice
a wrong password is entered five times in a row. to the user in order to enhance performance of the product.
The alarm sound is generated, and the lock is deactivated for 3 minutes. While the Place the card or key tag on the card reader, or enter the password, while
door is in this inactive mode, a single “Toot” sound is generated every 10 seconds the 9V battery is connected to the external power port of the outer body.
and seven consecutive “Toot~, Toot~, Toot~” will sound after 3 minutes. Following
this, the lock is released from inactive mode.)

Releasing the Alarm

Inside Press the [Register] button.

Outside Apply the registered card or key tag to the card reader, or enter
the password and then press the [] button.
10 11 12