INTERNATIONAL ISO
STANDARD 883
This is a preview of "ISO 883:2013". Click here to purchase the full version from the ANSI store.
Fourth edition
2013-09-01
Indexable hardmetal (carbide) inserts
with rounded corners, without fixing
hole — Dimensions
Plaquettes amovibles en métaux-durs (carbures métalliques) avec
arrondi de pointe, sans trou de fixation — Dimensions
Reference number
ISO 883:2013(E)
© ISO 2013
ISO 883:2013(E)
This is a preview of "ISO 883:2013". Click here to purchase the full version from the ANSI store.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@[Link]
Web [Link]
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 883:2013(E)
This is a preview of "ISO 883:2013". Click here to purchase the full version from the ANSI store.
Contents Page
Foreword......................................................................................................................................................................................................................................... iv
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references....................................................................................................................................................................................... 1
3 Types of insert.......................................................................................................................................................................................................... 1
4 Interchangeability............................................................................................................................................................................................... 1
4.1 Tolerances.................................................................................................................................................................................................... 1
4.2 Thickness, s, of inserts with chip breakers...................................................................................................................... 2
5 Designation and marking............................................................................................................................................................................. 2
5.1 Designation................................................................................................................................................................................................. 2
5.2 Marking.......................................................................................................................................................................................................... 2
6 Measurement............................................................................................................................................................................................................ 2
7 Recommended dimensions........................................................................................................................................................................ 2
7.1 General............................................................................................................................................................................................................ 2
7.2 Triangular inserts.................................................................................................................................................................................. 3
7.3 Square inserts........................................................................................................................................................................................... 4
Annex A (informative) Tolerances for d, m and s...................................................................................................................................... 7
Annex B (informative) Method of measurement of “m” dimension...................................................................................... 8
Annex C (informative) Inserts with rounded corners without fixing hole, with shapes covered by
this International Standard.....................................................................................................................................................................10
Annex D (informative) Relationship between designations in this International Standard and
ISO 13399 (all parts)......................................................................................................................................................................................12
Bibliography.............................................................................................................................................................................................................................. 13
© ISO 2013 – All rights reserved iii
ISO 883:2013(E)
This is a preview of "ISO 883:2013". Click here to purchase the full version from the ANSI store.
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. [Link]/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. [Link]/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with
cutting edges made of hard cutting materials.
This fourth edition cancels and replaces the third edition (ISO 883:1985), of which it constitutes a
minor revision.
iv © ISO 2013 – All rights reserved
