Scribd
Upload
28 views5 pages

TP Voice+Routage

The document describes the configuration of two routers to set up VLANs, assign IP addresses to each VLAN interface, configure DHCP pools for each VLAN network, and exclude certain IP addresses from being assigned by DHCP. On Router1, VLANs 10, 20 and DHCP pools are configured for VLAN networks 10 and 20. On Router2, VLANs 30, 40 and DHCP pools are configured for VLAN networks 30 and 40, along with options to exclude addresses and provide the VLAN gateway address via DHCP option 150.

Uploaded by

yassine rezgui
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
28 views5 pages

TP Voice+Routage

The document describes the configuration of two routers to set up VLANs, assign IP addresses to each VLAN interface, configure DHCP pools for each VLAN network, and exclude certain IP addresses from being assigned by DHCP. On Router1, VLANs 10, 20 and DHCP pools are configured for VLAN networks 10 and 20. On Router2, VLANs 30, 40 and DHCP pools are configured for VLAN networks 30 and 40, along with options to exclude addresses and provide the VLAN gateway address via DHCP option 150.

Uploaded by

yassine rezgui
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

Router1 :

Router>ena
Router>enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int
Router(config)#interface f0/1
Router(config-if)#no sh
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#int
Router(config-if)#int
Router(config-if)#exit
Router(config)#int
Router(config)#interface f0/1.10
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.10, changed state to


up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.10.1 255.255.255.0
Router(config-subif)#no sh
Router(config-subif)#no shutdown
Router(config-subif)#exit
Router(config)#int
Router(config)#interface f0/1.20
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.20, changed state to


up

Router(config-subif)#enc
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.20.1 255.255.255.0
Router(config-subif)#no sh
Router(config-subif)#no shutdown
Router(config-subif)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip dhcp pool lanvoice
Router(dhcp-config)#netwo
Router(dhcp-config)#network 192.168.10.0 255.255.255.0
Router(dhcp-config)#def
Router(dhcp-config)#default-router 192.168.10.1
Router(dhcp-config)#exit
Router(config)#ip dhc
Router(config)#ip dhcp exc
Router(config)#ip dhcp excluded-address 192.168.10.1 192.168.10.5
Router(config)#ip dhc
Router(config)#ip dhcp pool landata
Router(dhcp-config)#net
Router(dhcp-config)#network 192.168.20.0 255.255.255.0
Router(dhcp-config)#defr
Router(dhcp-config)#defa
Router(dhcp-config)#default-router 192.168.20.1
Router(dhcp-config)#exit
Router(config)#ip dh
Router(config)#ip dhcp exc
Router(config)#ip dhcp excluded-address 192.168.20.1 192.168.20.5
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Router con0 is now available


Press RETURN to get started.

Router>ena
Router>enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip dhcp pool lanvoice
Router(dhcp-config)#op
Router(dhcp-config)#option 150 ip 192.168.10.1
Router(dhcp-config)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#
Router2 :
Press RETURN to get started!

Router 1 :

Router>ena
Router>enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int
Router(config)#interface f0/1
Router(config-if)#no sh
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int
Router(config)#interface f0/1.30
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.30, changed state to


up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 30
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.30.1 255.255.255.0
Router(config-subif)#no sh
Router(config-subif)#no shutdown
Router(config-subif)#exit
Router(config)#int
Router(config)#interface f0/1.40
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.40, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.40, changed state to


up

Router(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 40
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.40.1 255.255.255.0
Router(config-subif)#no sh
Router(config-subif)#no shutdown
Router(config-subif)#exit
Router(config)#ip dhcp pool lanvoice
Router(dhcp-config)#net
Router(dhcp-config)#network 192.168.30.0 255.255.255.0
Router(dhcp-config)#def
Router(dhcp-config)#default-router 192.168.30.1
Router(dhcp-config)#exit
Router(config)#ip dh
Router(config)#ip dhcp ex%DHCPD-4-PING_CONFLICT: DHCP address conflict: server
pinged 192.168.30.1.

% Incomplete command.
Router(config)#ip dh
Router(config)#ip dhcp ex
Router(config)#ip dhcp excluded-address 192.168.30.1 192.168.5
^
% Invalid input detected at '^' marker.
Router(config)#ip dhcp excluded-address 192.168.30.1 192.168.30.5
Router(config)#ip dh
Router(config)#ip dhcp pool landata
Router(dhcp-config)#netw
Router(dhcp-config)#network 192.168.40.0 255.255.255.0
Router(dhcp-config)#def
Router(dhcp-config)#default-router 192.168.40.1
Router(dhcp-config)#exit
Router(config)#ip dhc
Router(config)#ip dhcp exc
Router(config)#ip dhcp excluded-address 192.168.40.1 192.168.40.5
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip dh
Router(config)#ip dhcp pool lanvoice
Router(dhcp-config)#op
Router(dhcp-config)#option 150 ip 192.168.30.1
Router(dhcp-config)#exi
Router(dhcp-config)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

You might also like